1. business and industrial
2. chemicals industry
3. adhesives

CIVIL & INTERIOR FURNISHING WORKS
TENDER - CIVIL & INTERIOR FURNISHING WORKS
FOR
BRANCH
AT
APMC MARKET VASHI – TURBHE BRANCH
Shop No. 1001 to 1004, 2001 to 2002 and 3001 to 3002,
B wing, Mayuresh Trade Center (City Mall)
Vashi, Navi Mumbai 400 703.
ARCHITECTS:
M/s Prakash Walavalkar & Associates
102, Ameya Tower,
1139 Pavwala Street, Grant Road
Mumbai 400 004
Tel: 28822143 / 23855343
Mobile: 9869015343
Email: [email protected]
[email protected]
PART II– FINANCIAL BID
Page 0
CIVIL & INTERIOR FURNISHING WORKS
CONTENTS
INDEX
INSTRUCTION
BILL OF QUANTITIES
DRAWINGS
PART II– FINANCIAL BID
PAGE NO
2
3 – 14
15
Page 1
CIVIL & INTERIOR FURNISHING WORKS
INSTRUCTIONS
1. The Bill of Quantities shall be read in conjunction with the Drawings, Conditioners of Contract
and Specifications, as these documents are jointly explanatory and descriptive of the works
included in the Contract.
2. General directions and descriptions of work and materials given elsewhere in the Contract
documents are not necessarily repeated in the Bill of Quantities. Reference is to be made to
the other documents for information.
3. The Contractor shall be deemed to have visited the site before preparing his Tender and to
have examined for himself the conditions under which the work will be priced and all other
factors affecting the execution of the work and the cost thereof.
4. The Quantities of work and material in the Bill of Quantities are not to be considered as
limiting or extending the scope of work to be done and materials to be supplied by the
Contractor. The quantities in the Bill of Quantities are an estimate of the amount work but
the work will be measured on complete and the contractor will be paid on the actual
measurement of work approved by the Architect.
5. Any special methods of measurements used are stated at the head of or in text of the Bills of
Quantities for the items affected. All other items are measured net in accordance with the
drawings and no allowance has been made for wastage. Unless otherwise specified
measurements shall be as per relevant Indian Standard.
6. A price or rate in figures is to be entered against the item in the Bill of Quantities, whether
quantities are stated or not. Item against which no price is entered will be considered as
covered by other prices or rates in the Bills.
7. The prices and rates interested are to be the full inclusive value of the works described under
the various items, including all costs and expenses which may be required for the completion
of the work described, together with all cost and obligations set forth or implied in the
conditions of Contract, Specifications and the Drawings.
8. Some finishing items may be quantity wise completely altered (either added or omitted) and
the same shall not affect any rates quotes.
9. Where prices have been entered against Lump sum items, payment for such affected items
shall be made in proportion to the extent of which works have been done at the time of billing
and the same is at discretion of the Architect.
10. “Providing and Fixing” shall mean that the Contractor has to provide such materials not being
procured and borne by the Bank, but which are required for the item and if no materials need
be provided by the Contractor, the rate shall be only for fixing of the component covered in
the item.
PART II– FINANCIAL BID
Page 2
CIVIL & INTERIOR FURNISHING WORKS
BILL OF QUANTITIES
Sr.
No.
A
Description
Unit
Qty
A1
Dismantling Existing Flooring / Ceiling / Partition /
Loft / Walls / Plaster / Doors / Windows etc as
directed by the architects. Rate Including removal of
debris from site and dumping the same in the
nearest municipal dump.
L.S.
1.00
A2
Making small holes in internal/external brickwork,
chiselling etc. and making good the same, if required
to enable the Allied Contractors, for ex AC,
PLUMBING , ELECTRICAL AND LAN etc.to carry
out their installation work during the course of the
project.
Nos
5.00
A3
Providing and Laying plain cement concrete PCC of
1:3:6 of thickness of 75mm to100mm over the
entire floor area in line and level as indicated by the
Architect with vibrator for compaction inclusive of
curing etc.The finished surface to be smooth and
level in power trowel finish without any undulation.
Cost to include finishing of edges near junctionboxes, etc. Complete with all relevant debris, etc. to
be removed from the site, on a day-to-day basis.
Sq.Ft.
QRO
A4
6" THK BRICK WALL WITH PLASTER
Constructing 4.5” thk. Brick wall in 1:5 cement
mortars. Brick used shall be of best quality kiln burnt,
having sharp edges & giving clear ringing sound
when struck against each other. Necessary RCC
lintels of depth 4 ½” above door opening to be
provided. A 4 ½” R.C.C. Patli Beam shall run
horizontally @every 3’-0” c/c height of the wall. The
walls should be extended up to the ceiling height by
leaving space for return air for A/C ducting as
directed by Bank / Architect. The walls to be
plastered ¾” thick C.M.1:4 on both sides. The walls
should be finished in proper workmanship and with
neat finish.
Sq.Ft.
QRO
A5
VITRIFIED TILES FLOORING & SKIRTING 600mm
X 600mm Providing and fixing VITRIFIED Tiles
approved make, shade and pattern as shown in the
drg. / As approved by the bank / Architect. In CM1:4
in proper line and level without spacers for
maintaining the grid lines. 3 of 7. Rate shall be
inclusive of providing and laying necessary PCC and
Cement Mortar for a thickness of 3" and joint filling
compound of the same shade of the tiles
Sq.Ft.
25.00
Rate
Amount
Civil Works
PART II– FINANCIAL BID
Page 3
CIVIL & INTERIOR FURNISHING WORKS
A6
GRANITE SLAB FLOORING Providing and fixing
20mm thick machine cut and mirror polished Granite
slabs of approved colour in length upto 2400mm, set
in 20mm thick cement mortar 1:4, joint finished with
neat cement slurry with matching colour including
dressing the nosing and sides to the required shape
etc. as directed for Flooring, Jambs, Cills, Trims etc.
with sizes as per drawing. Rate to include final mirror
polish after installation.
Sq.Ft.
50.00
A7
PANTRY PLATFORM IN BLACK GALAXY
GRANITE (WITH SINK & COCK) Providing and
laying platform of 2’-0” width (clear) and at 2’-8”
height (top finished level) above floor level with
23mm thick granite slab ( Black Galaxy) with
champhered and machine polished Bull Nosed
edge. It shall be supported on vertical Brick wall 4.5"
& Horizontal RCC slab 3" thick. Necessary cut outs
to be made in the RCC slab and Granite slab with
polishing the edges and providing 18" x 18" size S.
S. Nirali sink without drain board (Nirali or equivalent
make). The waste line to be connected through a
Nahni Trap with necessary fittings. One jaguar
continental C. P. Sink cock with swinging cast spout
(no. 347) also to be provided
R.ft.
6.00
A8
Providing/Applying on external/internal walls, Floors
etc at all levels where water leakage is an issue
25mm thick Waterproof Cement Plaster Internal in
line, level and plumb including "Roff" Liquid
Chemical to be used or alternate chemical to be
approved by Architect complete as directed including
scaffolding, finishing & removing of existing plaster
etc.
Sq.Ft.
25.00
A
Total Civil Works
B
Fabrication & Window Works
B1
Collapsible Gate – P&F collapsible gate, with
interlocked arrangement in heavy approved
sections, including 2" frames on sides, top and
bottom guide rails with first quality enamel paint. For
Branch Entrance
Sq. Ft.
60.00
B2
M.S.GRILLS - Providing and fixing MS Grills for
windows / ventilators etc. using 12mm M. S. round
or square bar grills at 4" C/C fixed as per design /
drawings or as directed by Bank / Architects. The
works should be done with all necessary fittings etc
with proper workmanship and with 2 coats of anti
rust paint and 2 coats of Synthetic Enamel paint.
Sq. Ft.
50.00
PART II– FINANCIAL BID
Page 4
CIVIL & INTERIOR FURNISHING WORKS
B3
Rolling Shutter – P&F rolling shutter of 20
gauge MS sheet, including floor locks, guide rail,
first quality enamel paint
B
Total Fabrication Works
C
Furnishing Works
C1
Partly Glazed Partition for Cash Cabins
Sq. Ft.
QRO
Sq. Ft.
300.00
Sq. Ft.
235.00
R. Ft.
12.00
Providing and fixing in position 7’-7” high partly
glazed partition for Cash Cabins including door
frame work at 2’ x 2 ‘grid (horizontally and vertically)
comprising of 2” x 1½” T.W. Section and / or as per
frame work shown in the drawings with 6mm
plywood on both sides finished with 1 mm thick
laminates of approved shade and colour as shown in
drawings. Item to include 8 mm thick glass with
etching and frosting as per design and 2”x 2” T.W.
member for door sides and glass sides and T.W.
door frame to take 8 mm thick glass with etching and
frosting. The door will be provided with T.W. louvers
finished in melamine polish of matching laminate
colour. The doors are also to be provided with
Godrej Night Latch. Two wooden trays are also to
be provided as per drawing. Necessary cut-outs are
to be provided in the glass and the edges of the
glass cut-outs are to be finished in mirror polish. All
exposed T.W. surfaces to be finished in melamine
polish of matching laminate colour as directed
including all necessary Stainless Steel finish fittings/
hardware, door closers, Godrej locks and wood
preservative paint etc. as per list of approved
material and as approved by the Project Consultant/
Bank complete in all respects
C2
P & F non-transparent white film:
On glazed surfaces from inner side in pattern as
directed.
C3
Cash Counter:
Providing and fixing in position Cash Counter
the following :
2’-9” wide comprising of
Working top made with 25mm thick plywood finished with 1mm thick
laminate. Outside edge of the working top shall be provided with 1¼”X1”
Teak Wood moulding finished with melamine polish. Inside edge will be
provided with ½ “x 1” T.W. beading Patti with melamine polish.
Vertical fascia (Apron) made with 18mm thick plywood finished with 1mm
thick laminate with 1mm thick groove at the joint of laminates of two
different shades.
PART II– FINANCIAL BID
Page 5
CIVIL & INTERIOR FURNISHING WORKS
Vertical drop (horizontal band) shall be provided on the fascia below the
working top made with 18mm thick plywood finished with 1mm thick
laminate with provision for concealed light, 1 mm thick groove shall be
provided at the joint of two different shades of laminate.
Glazed partition of 1’-4” height above working top provided with 12mm
thick toughened and frosted glass besides non-transparent film from
inside fixed to partition as per fixing details and to boxing with concealed
S. S. finished ‘D’ brackets as shown in the drawing. The exposed edges
of the glass shall be finished in mirror polish.
Transaction top shall be provided with 12mm thick toughened glass
(partly glazed partly frosted) fixed horizontally with concealed Stainless
Steel D bracket. Both exposed edges (inside and outside) shall be
moulded and finished in mirror polish.
Glazed partition provided with 12mm thick glass (Clear) above the slit to
be fixed to partition as per fixing details and to boxing with concealed S.
S. finished ‘D’ brackets as shown in the drawing. The exposed edges
shall be finished in mirror polish.
7’-7” high Boxing (10”x 10”) made with 18mm thick plywood as per
drawing with 1-6” horizontal extension at the top including providing and
fixing 6 mm thick square frosted glass at a height of 5'-11” above Finished
Floor level.
1’-9” high boxing (5”x 5”) made with 12 mm thick plywood finished with 1
mm thick laminate are to be provided.
Telescopic CPU Stand / ready- made Keyboard tray shall be provided of
approved model and make.
Footrest made with T.W. section of size 4”X1 ½ “finished with French
polish.
Drawer units as per drawing shall be provided and each drawer should
have vertical partitions for keeping the currency notes and multipurpose
Godrej locks. Fascia of drawer unit shall be finished with 1mm thick
laminate and all other sides shall be finished with white enamel paint. The
drawers will be provided with handles (Stainless Steel finish) and
channels as per approval of the Project Consultant / Bank
Boxing as per drawing made with 12mm thick plywood finished with
Synthetic enamel paint shall be provided below the table top for electrical
conduiting and at the bottom for the LAN cabling/Telephone wire
conduiting. The item to include all necessary hardware and fittings in
Stainless Steel finish, lipping to all edges and making provision only for
electrical fitting behind the Vertical drop and also in the 10”x10” boxing as
shown in the drawing. Necessary beadings with matching melamine
polish for fixing the glass are to be provided as per drawing/ as directed.
C4
Front Office Counter:
R. Ft.
Providing and fixing in position Front Office Counter
comprising of the following complete in all respects:PART II– FINANCIAL BID
16.00
2’-6” wide
Page 6
CIVIL & INTERIOR FURNISHING WORKS
Working top made with 25mm thick plywood finished with 1mm thick
laminate. Outside edge of the working top shall be provided with1¼”X1”
Teak Wood moulding finished with melamine polish. Inside edge will be
provided with ½ “x1” T.W. beading Patti with melamine finish.
Vertical fascia (Apron) made with 18mm thick plywood finished with 1mm
thick laminate with1mm thick groove at the joint of laminates of two
different shades.
Vertical drop (horizontal band) shall be provided on the fascia below the
working top made with 18mm thick plywood finished with 1mm thick
laminate with provision for concealed light, 1 mm thick groove shall be
provided at the joint of two different shades of laminate.
Glazed partition above working top to be provided with 12mm thick clear
glass cut to the standard shape fixed to partition as per fixing details and
to boxing with concealed S. S. finished ‘D’ brackets as shown in the
drawing. The exposed edges of the glass shall be finished in mirror
polish.
3’-10” high Boxing (10”x10”) made with 18 mm thick plywood finished with
1 mm thick laminate including providing and fixing 6 mm thick square
frosted glass at a height 3’-2” above finished floor level.
1’-9” high Boxing (5”x5”) made with 12 mm thick plywood finished with 1
mm thick laminate.
Vertical supports made with 18 mm thick plywood finished with white
enamel paint.
Telescopic CPU Stand/ readymade Keyboard tray shall be provided of
approved model and make.
Footrest made with T.W. Member of size 4”X1 ½ “finished with French
polish.
Drawer units as per drawing shall be provided with multipurpose Godrej
locks in
Each drawer. Fascia of drawer unit shall be finished with 1mm thick
laminate and all other sides shall be finished with white enamel paint. The
drawers will be provided with handles (Stainless Steel finish) and
channels as per approval of the Project Consultant / Bank
Boxing as per drawing made with 12mm thick plywood finished with
Synthetic enamel paint shall be provided below the table top for electrical
conduiting and at the bottom for the LAN cabling/Telephone wire
conduiting.
The item to include all necessary hardware and fittings in Stainless Steel
finish, lipping to all edges and making provision only for electrical fitting
behind the front. Vertical drop and also in the 10”x10” boxing as shown in
the drawing. Necessary beadings with melamine or fixing the glass are to
be provided.
PART II– FINANCIAL BID
Page 7
CIVIL & INTERIOR FURNISHING WORKS
C5
Partly Glazed Full Height Partition Providing and
fixing in position including door as shown in the in
frame work at 2’ x 2 ‘grid (horizontally and vertically)
comprising of 2” x 1½” T.W. Section and / or as per
frame work shown in the drawings with 6mm
plywood on both sides finished with 1 mm thick
laminates of approved shade and colour as shown in
drawings.
Sq. Ft.
535.00
Item to include 8 mm thick glass with etching and frosting as per design
and 2”x 2” T.W. member for door sides and glass sides and T.W. door
frame to take 8 mm thick glass with etching and frosting. All exposed
T.W. surfaces to be finished in melamine polish of matching laminate
colour as directed including all necessary Stainless Steel finish fittings/
hardware, door closers, Godrej locks and wood preservative paint etc. as
per list of approved material and as approved by the Project Consultant/
Bank complete in all respects.
(Note: In case of false ceiling, the vertical T.W. members to be fixed with
pucca ceiling but the area of partition payable will be below the false
ceiling only).
C6
Partly Glazed Low Height Partition Providing and
fixing in position partly glazed low height partition
(21/2” thick) in frame work with T.W vertical
members at 2’ c/c and 3 horizontal members at
equal distance comprising of 2”x 1½” T.W. Section
with 6 mm plywood on both sides finished with 1 mm
thick laminates of approved make and .Item to
include 12 mm thick glass (clear/frosted) to be fixed
as shown in drawing. The exposed edges of the
glass to be finished in mirror polish. T.W runner
should be melamine polished in matching colour of
laminate etc complete in all respects.
Sq. Ft.
85.00
C7
Solid Full Height Partition - Providing & fixing in
position solid Full Height Partition in frame work
including door in 2’x 2’ grid (horizontally and
vertically) comprising of
2”x 1½” T.W. Section
with 6 mm thick plywood on both sides finished with
1 mm thick laminates of approved make and colour.
Item to include 2” x 2” T.W. member for door-frame.
All exposed T.W. surfaces to be finished in
melamine polish of matching laminate colour as
directed including all necessary Stainless Steel finish
fittings/ hardware, door closers, Godrej locks and
wood preservative paint etc. as per list of approved
material and as approved by the Project Consultant/
Bank complete in all respects.
Sq. Ft.
575.00
(Note: In case of false ceiling, the vertical T.W. members to be fixed with pucca
ceiling but the area of partition payable will be below the false ceiling only).
PART II– FINANCIAL BID
Page 8
CIVIL & INTERIOR FURNISHING WORKS
C8
Full height Storage / Low Height Storage / Back
Storage(Credenza)
Sq. Ft.
250.00
R.ft.
6.00
Providing and fixing in position Full height Storage /
Low Height Storage/ Back Storage(Credenza) as
shown in Drawing respectively using Plywood of
required thickness finished with 1mm thick laminates
as shown in the drawing and all other sides shall be
finished with white enamel paint as detailed therein.
The Storage Units shall be provided with handles
(Stainless Steel finish) as per approval of the Project
Consultant / Bank.
All exposed plywood surfaces
to be finished with 1mm thk. Laminate of approved
make & shade and all exposed edges of plywood to
have 1" x 1/4" T.W. lipping. All exposed T.W.
sections to be melamine in matching colour laminate
and internal surfaces to have white enamel paint as
directed. Item to include all necessary hardware and
fittings in Stainless Steel finish, Godrej multi-purpose
locks including magnetic ball catcher etc., complete
in all respects
C9
Manager’s Table
Providing and fixing in position Manager’s Table of
size 6’x 2'-9" as per drawing / Officer’s Table of size
4’-6” x 2’-3” as per drawing
including Side
Storage(Credenza) by using 25mm thick plywood
for top and 18 mm thick plywood for all other
horizontal and vertical members. Telescopic CPU
Stand/ ready -made Keyboard tray shall be provided
of approved model and make. Footrest made with
T.W. Member of size 4”x 1 ½ “finished with French
polish.
Side Storage (Credenza) as per drawing shall be
provided. Fascia of Side Storage (Credenza) shall
be finished with 1mm thick laminates as shown in
the drawing and all other sides shall be finished with
white enamel paint. The Side Storage (Credenza)
shall be provided with handles (Stainless Steel
finish) and channels as per approval of the Project
Consultant / Bank. All exposed plywood surfaces to
be finished with 1mm thk. Laminate of approved
make & shade, and all exposed edges of table top &
ply verticals to have 1" x 1/4" T.W. lipping. All
exposed T.W. sections to be melamine polished and
internal surfaces to have white enamel paint as
directed. Item to include plywood boxing, all
necessary hardware and fittings in Stainless Steel
finish, lipping to all edges etc. complete in all
respects
PART II– FINANCIAL BID
Page 9
CIVIL & INTERIOR FURNISHING WORKS
C10
Officer’s Table
Rft.
20.00
Rft.
16.00
Providing and fixing in position Manager’s Table of
size 6’x 2'-9" as per drawing / Officer’s Table of size
4’-6” x 2’-3” as per drawing including Side Storage
(Credenza) by using 25mm thick plywood for top
and 18 mm thick plywood for all other horizontal and
vertical members. Telescopic CPU Stand/ ready made Keyboard tray shall be provided of approved
model and make. Footrest made with T.W. Member
of size 4”x 1 ½ “finished with French polish.
Side Storage (Credenza) as per drawing shall be
provided. Fascia of Side Storage (Credenza) shall
be finished with 1mm thick laminates as shown in
the drawing and all other sides shall be finished with
white enamel paint. The Side Storage (Credenza)
shall be provided with handles (Stainless Steel
finish) and channels as per approval of the Project
Consultant / Bank. All exposed plywood surfaces to
be finished with 1mm thk. Laminate of approved
make & shade, and all exposed edges of table top &
ply verticals to have 1" x 1/4" T.W. lipping. All
exposed T.W. sections to be melamine Polish and
internal surfaces to have white enamel paint as
directed. Item to include plywood boxing, all
necessary hardware and fittings in Stainless Steel
finish, lipping to all edges etc. complete in all
respects
C11
Staff Table / May I Help U Table
Providing and fixing in position Staff Table of size 4'
0" x 2' 0" as per drawing by using 25mm thick
plywood for top and 18 mm thick plywood for all
other horizontal and vertical members. Telescopic
CPU Stand/ readymade Keyboard tray shall be
provided.
Drawer units as per drawing shall be provided with
multipurpose Godrej locks in each drawer. Fascia of
drawer unit shall be finished with 1mm thick laminate
and all other sides shall be finished with white
enamel paint. The drawers will be provided with
handles (Stainless Steel finish) and channels as per
approval of the Project Consultant / Bank.
PART II– FINANCIAL BID
Page 10
CIVIL & INTERIOR FURNISHING WORKS
All exposed plywood surfaces to be finished with
1mm thk. Laminate of approved make & shade, and
all exposed edges of table top & ply verticals to have
1" x 1/4" T.W .lipping. All exposed T.W. sections to
be melamine an internal surface to have white
enamel paint as directed. The item to include
plywood boxing, all necessary hardware and fittings
in Stainless Steel finish, lipping to all edges etc.
complete in all respects.
C12
Aluminium Heavy Duty Front Glazing with
powder coated sections
Sq. Ft.
50.00
Sq. Ft.
1150.00
Sq. Ft.
375.00
Sq. Ft.
490.00
Sq. Ft.
75.00
Providing and fixing fully glazed heavy duty
aluminium sections (14 Gauge) at the main entrance
as shown in the drawing. Glazing shall consist of
approved make heavy duty 6" x 2" sections for the
top & bottom rails and 2" x 2" sections for the vertical
styles. 10mm thk. Approved make clear float glass
shall be provided and fixed in the framing. Rate shall
include necessary etching film / LOGO, and any
necessary hardware items. (Heavy Duty 6" & 2" thick
frames(14 Gauge) - approved make)
C13
Wall & Column Panelling In Branch:
P & F 1 ½” x 1” T.W. frame work covered with
12mm commercial plywood & laminating as per new
brand image to mate and match rest of décor.
Laminate 3 - ‘Silicon 9850SF’
Laminate 4 - ‘Greenlam 9001’
C14
Wall / Column Panelling (Silver laminate):
Framing in 2” x 1” T.W. covered with 12 mm comm.
ply & finished with Silver laminate (Greenlam 9001
Silver)
C15
Wall & Column Panelling In E- Lobby
P & F 1 ½” x 1” T.W. frame work covered with 12mm
commercial plywood & laminating as per new brand
image to mate and match rest of décor.
Lamination inside the E- lobby as per new brand
image for E-lobby. Lamination in the branch area
to mate and match existing laminate in the
banking hall.
C16
Glazed Divider at E_LOBBY
Providing and fixing fully glazed divider in 12mm
thick toughened glass, fixed with approved SS
bracket as directed
PART II– FINANCIAL BID
Page 11
CIVIL & INTERIOR FURNISHING WORKS
C17
Roller Blinds: Providing & fixing approved Roller
blinds as directed.
Sq. Ft.
100.00
Sq. Ft.
50.00
Nos.
3.00
Sq. Ft.
60.00
Sq. Ft.
200.00
Nos.
1.00
‘MAC’ ‘Vista’
C18
Soft Boards:
P & fixing soft board panelling directly on wall /
column [basic fabric cost Rs.150/-Mtr.]
P & F 12mm thk soft boards covered with approved
with fabric on 12 mm thick comm. plywood back as
directed. Work includes frame out of 1” x ½” TW
moulding with melamine polish to match rest of the
décor.
C19
Providing & Fixing 35mm Solid flush single door:
(Overall size 3'-0" x 7' 0" ht.) Finished in laminate
completely with hardware such as Dead lock,
handles, floor springs.
Laminate 3 - ‘Silicon 9850SF’
Laminate 4 - ‘Greenlam 9001’
C20
Branch & E-Lobby Entrance Door
Providing and fixing Entrance Door (glazed) in Silver
Anodized aluminium door section (Jindal make) in
top and bottom, glazed with 12 mm thick glass of
approved make with etching and frosting. Item to
include floor springs, lock, all necessary hardware of
Stainless Steel finish as approved by the Project
Consultant/ Bank complete in all respects.
C21
Door size: 8’ x 3’6” each. X 1 doors
P & F Composite panel on Entrance Façade:
Out of aluminium composite panel boxing with PVDF
coating & LDPE core laminated ‘Eurobond’/
‘Altobond’ / ‘Alukbond’ Exterior grade 4mm thick with
composite of (0.5mm-3mm-0.5mm) including
fabrication for the same with aluminium sections,
required hardware, silicon sealant (Dow, Corning
789) masking tape, etc. Complete in all respect.
C22
KEY BOX
Providing and fixing key box of size 1' 6"x1' 6"x 6"
with all sides and back with 18mm thick comm. Ply
wood and lockable glass shutters in 18mm ply , with
5 mm glass. Necessary hooks to be provided inside
the box. All exposed areas and inside to be finished
with 1 mm thick laminate of approved shade.
PART II– FINANCIAL BID
Page 12
CIVIL & INTERIOR FURNISHING WORKS
The edges of shutter and box to be lipped with
steam beach beading polished with melamine. Rate
shall be inclusive of all necessary approved fittings
like hinges, locks, hooks etc. and any necessary
hardware items.
C23
WALL MOUNTED WRITING TABLE 1'- 3" TO 1'6" WIDE
Nos.
2.00
Providing and Fixing wall mounted writing table as
per design. The top and central partitions should be
with 12mm thick float glass (approved make) with
champhered edge (Bevelled edges) for top piece
and verticals with edge polish. The glass should be
supported on 18mm thick comm. ply base, rear and
sides fixed to the wall. The bottom ply piece to be
supported additionally with 2 Nos. of SS Brackets.
The exposed faces should be finished with 1 mm
thick approved laminate and the edges of ply wood
to be provided with steam beach lipping finished with
melamine.
C
Total Furnishing Works
D
False Ceiling Works
D1
Providing & fixing in position gypsum board:6”X6”
COVE for Diffused lighting
R. Ft.
100.00
D2
False Ceiling (Gypsum Board) Providing & fixing in
position false ceiling in Gypboard 12mm thick for
horizontals & verticals fixed over G.I. framework as
specified by India Gypsum Co. Ltd. Including trap
doors for A.C unit in 18mm thick M.R. Grade
Plywood with Stainless Steel hinges & locks with
moulding 1” x 1” for edges including finishing with 2
Coats of White Plastic Emulsion Paint etc. complete
in all respects.
Sq. Ft.
1750.00
Sq. Ft.
720.00
(Note: Only the plan area will be measured for
payment. No extra payment will be made for cutouts, grooves, mouldings etc.)
D3
False Ceiling (Armstrong)
Providing & fixing in position false ceiling in
Armstrong 600 x 600 mm x 15/16 mm Dune
Supreme RH 99 Prima tile with Regular edge
framework as specified by Armstrong Co. With
Suspenders wherever required. Making necessary
framework for A.C. ducting, if any, and necessary
cut-outs for diffusers and light fittings, taping and
finishing to proper line & level, including making
PART II– FINANCIAL BID
Page 13
CIVIL & INTERIOR FURNISHING WORKS
Grooves and trap doors for A.C unit in 18mm thick
M.R. Grade Plywood with Stainless Steel hinges &
locks with moulding 1” x 1” for edges including
finishing with White Plastic Emulsion Paint etc.
complete in all respects.
(Note: Only the plan area will be measured for
payment. No extra payment will be made for cutouts, grooves, mouldings etc.)
D
Total False Ceiling Works
E
Painting Works
E1
Painting Providing & applying White Plastic
Emulsion paint of Asian Paints/ ICI Dulux / Berger
and Sporty Yellow-X104 shade of Royal Luxury
Emulsion of Asian Paints in minimum 2 coats
including scrapping, opening of existing cracks,
filling up of “V” cracks with epoxy expandable putty
to required depths, making good weak plastered /
un-plastered surfaces with cement plaster wherever
required. Item to include Plaster of Paris, primer,
palti & making good existing surface to receive new
paint including cleaning on completion of painting
work etc. complete in all respects.
Sq. Ft.
2500.00
E2
Enamel paint to grills, metal surfaces, wooden
sections etc., as directed.
Sq. Ft.
100.00
E
Total Painting Works
F
Municipal Formalities
L.S.
1
Total Amount [A+B+C+D+E+F]
Discount
Total After Discount
Total Amount In Words :
Rate inclusive of all Material charges, Transportation, Local levies as applicable, Loading, Unloading, Lifting- Shifting,
Erection, Testing , Commissioning, Scaffolding, VAT, Sales tax, any additional/ duties, excise, custom duty etc. as applicable.
Contractor Name :
Address
PART II– FINANCIAL BID
Sign & Seal
Page 14
CIVIL & INTERIOR FURNISHING WORKS
DRAWINGS – GENERAL LAYOUT
PART II– FINANCIAL BID
Page 15