1. No category

3045
Hand Held Programmer
USER OPERATING INSTRUCTIONS
FEATURES
FEATURES CODE
MANAGER CODE (Factory set to 1-2-3-4-5-6) ...................
• Add/Remove Second User
• Enable/Disable Second User
TIME DELAY OVERRIDE ......................................................
• Ability to add second combination to override delay period
DUAL CODE .........................................................................
• Two combinations required to open
SILENT SIGNAL ALARM (Optional Alarm Box Required)
...
• Duress signal if last number of code(s) is entered using one
number higher or one number lower
DISABLE LOCK (Optional Alarm Box Required)
.................
• Input signal disables opening of lock by valid code
TIME DELAY .........................................................................
• Delay period 1 - 99 minutes
• Open period 1 - 19 minutes
0
1
2
3
7
01:01
SET PROGRAMMER SWITCHES AND FEATURE TRANSMISSION
(See Switch Diagram on back page)
When adding features via the Hand Held Programmer, all features required must be added at the same time.
Adding an additional feature later will re-program the lock to only that feature.
Manager Code
The lock is sent from the factory with the Manager code set to 1-2-3-4-5-6. If no other features will be added to the
lock, the Manager can add a User on the keypad. If other features are added after the User has been set-up on the
keypad (please see Manager Instructions for your lock), the User will be deleted and have to re-added after new setup is complete.
Setting Switches
The COMBOGARD and SAFEGARD locks are set by turning switches ON or OFF via the Hand Held Programmer.
Follow the steps below to set the lock to the features required.
1 Turn switch(s) to the ON position to select features.
• Only Silent Signal Alarm and Time Delay may be used with other features.
2 Connect Programmer to the lock via the port marked ENT.
• INITIAL SET-UP: Enter the factory pre-set Manager Code (1-2-3-4-5-6)
• FIELD SET-UP: Enter the valid Manager Code
During the code entry display will show
• The top number shows the software version in the lock.
• The bottom number will change as each number in the code is entered.
© copyright 2006
12-210v3
LA GARD INC - A Member of The Kaba Group
• If code is invalid, LCD will display “Err” then go blank. If four (4) consecutive invalid codes are entered, LCD
displays “Pen” and a five (5) minute penalty starts.
• If code is valid, LCD displays Programmer switch settings as follows: (See Page 1 for feature codes.)
• If an incorrect feature is selected the applicable feature codes will flash. Press 9 to escape, reset switches and
restart the procedure.
3 Press and hold the 0 key to transmit the setting to the lock. Once the programming has been received
by the lock, the display will show:
• If the transmission to the lock does not go through, the display will show:
• If the transmission fails, check all connections, switch settings, batteries and restart procedure.
VERIFY SWITCH SETTINGS
1 Connect Programmer to the lock. Enter lock’s Manager Code. LCD will display Programmer Setting
2 Press 1 and LCD will display lock setting.
• If Programmer is not connected to the lock, Press 33. LCD will display Programmer switch
settings.
S3
S4
E
OD
E
M
ID
R
RR
DE
GE
E
A
M
CO
OV
AN
L
AR
Y
A
M
AL
LA
DU
E
T
D
N
E
LE
M
SI
TI
S5
S2
Sw
itc
h
“O
PE
N
Sw TIM
Sh
itc E”
h
ow
P
n i Valu ER
IO
nM
e
8
D
inu s
tes
1
2
(M
4
IN
UT
ES
)
S6
Nu
mb
er
s
(S
wi
tch
es
sh
ow
n
S1
(M
IN
UT
ES
)
(M
IN
UT
ES
)
“D
EL
AY
S8
in
OF
F
1
2
4
(M
IN
UT
ES
)
po
sit
ion
)
TIM
RE
E”
MO
Sh
PE
TE
ow
R
OV
ni
IO
ER
D
nM
RI
Sw
i
DE
n
8
itc
ute
hV
s
alu
e
S7
Ma
xim
um
=9
12-210v3
10
20
40
(M
IN
80
UT
ES
)
mi
nu
tes
Ma
xim
um
© copyright 2006
10
=9
0M
inu
tes
LA GARD INC - A Member of The Kaba Group
SAMPLE SET-UP - DUAL CODE
1 Turn the #3 switch in the S3 switch block to the ON position.
2 Connect Programmer to the lock via the port marked ENT.
• INITIAL SET-UP: Enter the factory pre-set Manager Code (1-2-3-4-5-6)
• FIELD SET-UP: Enter the valid Manager Code
During the code entry display will show
• The top number shows the software version in the lock.
• The bottom number will change as each number in the code is entered.
3 Press and hold the 0 key to transmit the setting to the lock. Once the programming has been
received by the lock, the display will show:
© copyright 2006
12-210v3
LA GARD INC - A Member of The Kaba Group