Shimaden, Temperature and Humidity Control Specialists °C %RH Series GAT10 SHIMADEN COMMUNICATION ADAPTOR GAT10-DN GAT10-CC • DeviceNet is a registered trademark of ODVA (Open DeviceNet Vendor Associations, Inc.). • The CC-Link is the open field network of the CC-Link Association. BASIC FEATURES Best solution for PLC-Shimaden application! Up to 8 Shimaden Controllers can be controlled through DeviceNet / CC-Link. Enables easy (programless) access to all parameters from Master PLC. No manual configuration required. Quick response - Scan time for 8 Controllers: approx. 1.5 sec. Provides cost-effective "Less Wiring" networking and "Application Flexibility" solution to total system integration, especially, to wide spread device installation. DeviceNet/RS-485 Protocol Converter GAT10-DN GAT10-DN • A programless communication between any controller using the Shimaden standard protocol and the DeviceNet is made possible. • It allows measured values and set values of temperature and the parameters of a maximum of eight Shimaden products having the RS-485 communication function to be read and written through the DeviceNet Master PLC. • When various units are installed separately in different devices, the amount of wiring for an entire system can be reduced. ORDERING INFORMATION Items SERIES NETWORK SYSTEM CODE GAT10DN9008- POWER SUPPLY 0 9 REMARKS SPECIFICATIONS Protocol Converter DeviceNet 100~240V AC 10% (50/60Hz) 24V AC (50/60Hz) / DC 10% Without With (Please consult before ordering.) EXAMPLE SYSTEM CONFIGURATIONS DeviceNet Master PLC GAT10-DN Other slave stations of DeviceNet Scan times average 1.5 seconds or shorter (when connected with 8 controllers) RS-485 (Shimaden standard protocol) Up to 8 controllers Supported Models List Digital controller: Programmable controller: SR90, SR80, SR253 FP93 Digital indicator: SD16 Servo controller: EM70 DeviceNet is a registered trademark of ODVA (Open DeviceNet Vendor Associations, Inc.). SPECIFICATIONS Model • GAT10-DN Display (LED) • Confirmation of power 'on' • DeviceNet Status : DeviceNet Protocol Converter : POWER (Green) : MS (Green/Red: module status) : NS (Green/Red: network status) • RS-485 Communication : RX (Green: during receiving) : TX (Green: during transmission) DeviceNet/Setting of communication speed • Setting system : by front dip switches • Station No. : 0~63 Communication speed : 125k, 250k, 500k bps Network • DeviceNet applicable specifications : Volume 1 Release 2.0 : Volume 2 Release 2.0 • RS-485 Communication speed : 19,200bps fixed Data format : Data 7 bits Even parity Stop 1 bit Communication protocol : Shimaden standard protocol Connectable products : SR90, SR80, SR253, SD16, FP93, EM70 The number of connectable products : Max. 8 (excluding this instrument) General Specification • Environmental conditions for instrument operation, Ambient Temperature : –10~50˚C Ambient Humidity : 90% RH (no dew condensation) Altitude : 2000m from the sea level or lower Category : II Degree of pollution :2 • Storage temperature : –20~65˚C • Supply voltage : 100~240V AC±10% 50/60Hz 24V AC±10% 50/60Hz 24V DC±10% • Power consumption : 5VA (100~240V AC) : 4VA (24V AC) : 3W (24V DC) • Conformity with standards : IEC61010-1 and EN61010-1 • Insulation resistance Between input/output terminals and power terminal : 500V DC 20 MΩ or above Between input/output terminals and ground terminal : 500V DC 20 MΩ or above • Dielectric strength Between input/output terminals and power terminal : 2300V AC 1 minute (Faradic current 3mA) Between power terminal and ground terminal : 1500V AC 1 minute (Faradic current 3mA) • Material of case : PPO resin molding • Color of case : Black • External dimensions : H80 × W50 × D120mm (including base, excluding front connector) • Mounting : DIN rail/fixed by screw • Weight : Approx. 250g CC-Link/RS-485 Protocol Converter GAT10-CC GAT10-CC • A programless communication between any controller using the Shimaden standard protocol and the CC-Link is made possible. • It allows measured values and set values of temperature and the parameters of a maximum of eight Shimaden products having the RS-485 communication function to be read and written through the CC-Link. • When various units are installed separately in different devices, the amount of wiring for an entire system can be reduced. ORDERING INFORMATION Items SERIES NETWORK SYSTEM CODE GAT10CC9008- POWER SUPPLY 0 9 REMARKS SPECIFICATIONS Protocol Converter CC-Link 100~240V AC 10% (50/60Hz) 24V AC (50/60Hz) / DC 10% Without With (Please consult before ordering.) EXAMPLE SYSTEM CONFIGURATIONS CC-Link master station PLC (Product of Mitsubishi Electric) GAT10-CC Other slave stations of CC-Link SR-83 (specified for use in CC-Link system) Scan times average 1.5 seconds or shorter (when connected with 8 controllers) RS-485 (Shimaden standard protocol) Up to 8 controllers Supported Models List Digital controller: Programmable controller: SR90, SR80, SR253 FP93 Digital indicator: SD16 Servo controller: EM70 The CC-Link is the open field network of the CC-Link Association. SPECIFICATIONS Model • GAT10-CC Display (LED) • Confirmation of power 'on' • CC-Link Status : CC-Link Protocol Converter : POWER (Green) : LRUN (Green: establishing communication link) : LERR (Orange: communication error) : RD (Green: during receiving) : SD (Green: during transmission) • RS-485 Communication : RX (Green: during receiving) : TX (Green: during transmission) CC-LINK Station No./Setting of communication speed • Setting system : by 3 front rotary dip switches • Setting range, Station No. : 1~61 Communication speed : 156k, 625k, 2.5M, 5M, 10M bps Network • CC-Link Version : 1.10 Type of station : Remote device station The number of occupying stations :4 • RS-485 Communication speed : 19,200bps fixed Data format : Data 7 bits Even parity Stop 1 bit Communication protocol : Shimaden standard protocol Connectable products : SR90, SR80, SR253, SD16, FP93, EM70 The number of connectable products : Max. 8 General Specification • Environmental conditions for instrument operation, Ambient Temperature : –10~50˚C Ambient Humidity : 90% RH (no dew condensation) Altitude : 2000m from the sea level or lower Category : II Degree of pollution :2 • Storage temperature : –20~65˚C • Supply voltage : 100~240V AC±10% 50/60Hz 24V AC±10% 50/60Hz 24V DC±10% • Power consumption : 10VA (100~240V AC) : 5VA (24V AC) : 4W (24V DC) • Conformity with standards : IEC61010-1 and EN61010-1 • Insulation resistance Between input/output terminals and power terminal : 500V DC 20 MΩ or above Between input/output terminals and ground terminal : 500V DC 20 MΩ or above • Dielectric strength Between input/output terminals and power terminal: : 2300V AC 1 minute (Faradic current 3mA) Between power terminal and ground terminal : 1500V AC 1 minute (Faradic current 3mA) • Material of case : PPO resin molding • Color of case : Black • External dimensions : H80 × W50 × D130mm (including base) • Mounting : DIN rail/fixed by screw • Weight : Approx. 260g Series GAT10 20 GAT10-DN DeviceNet status LED 80 MS NS RX TX V– CAN_L Drain CAN_H RESET POWER V+ SHIMADEN RS-485 Communitation status LED 7.8 0.2 Hole of 4.5 in diameter 35.4 MS: Module status LED Lit in green when the module is functioning normally. NS: Network status LED Lit in green when the module is communicating with the network normally. 8-M3.5 7 Approx. 2 100 Transmission rate setting switch (SW6, SW7) 81 maximum 120 (NA0~NA5) 40 0.2 51 maximum Approx. 4 50 Mountable on DIN rail GAT10-DN EXTERNAL DIMENSIONS AND TERMINAL ARRANGEMENT DIAGRAM Front View Node address setting switch Transmission rate setting Unit: mm Transmission rate SW6 SW7 RX: Blink in green when the module is receving data from controller. TX: Blink in green when the module is sending data to controller. 125kbps OFF OFF 250kbps ON OFF 500kbps OFF ON Inhibition of setting ON Terminal Layout 6 5 4 3 ON Reset switch (for resetting the module) 7 8 1 2 Signal No. 1 2 3 4 5 6 7 8 RS-485 FG N L Power supply SG RS-485 DeviceNet connector Note: A set value becomes effective upon applying power or resetting. For details, see "DeviceNet Specification" issued by ODVA. GAT10-CC EXTERNAL DIMENSIONS AND TERMINAL ARRANGEMENT DIAGRAM Front View ×1 30 This apparatus is of the 4 possessory station type. Set the number of the first station. The setting range is from 01 to 61. The factory set value is 00. 7.8 0.2 Approx. 2 100 51 maximum Hole of 4.5 in diameter 81 maximum ×10 130 35.4 GAT10-CC B.RATE 11-M3.5 7 Switch for setting CC-Link station numbers. Mountable on rail 50 CC-Link transmission rate setting switch 80 RESET POWER RX SD TX SHIMADEN Operating condition of CC-Link is displayed. Transmission rate setting Position Transmission rate Operating condition of RS-485 communication is displayed. 0 156kbps 1 625kbps 2 2.5Mbps 3 Reset switch (for resetting the module) Approx. 4 LRUN LERR RD 4 5Mbps 10Mbps Factory set value is 156kbps. 40 0.2 Unit: mm Terminal Layout 8 7 6 5 4 9 3 10 11 1 2 No. Signal 1 2 3 4 5 6 7 8 9 10 11 RS-485 SG FG Power N supply L FG SLD DG CC-Link DB DA Note: A set value becomes effective upon applying power or resetting. For details, see "CC-Link Specification" issued by the CC-Link Association Warning • The GAT10 series is designed to control temperature, humidity and other physical quantities of general industrial equipment. (It should not be used to control any object which might seriously affect the safety of personnel.) Caution • In case it is feared that a failure of this apparatus will impair or damage the system or any other property, take appropriate measures for failure prevention before use of the apparatus is begun. The names of the companies and products described in this brochure are their registered trademarks. (The contents of this brochure are subject to change without notice.) Temperature and Humidity Control Specialists ISO 9001 Head Office: 2-30-10 Kitamachi, Nerima-Ku, Tokyo 179-0081 Japan Phone: +81-3-3931-7891 Fax: +81-3-3931-3089 E-MAIL: [email protected] URL: http://www.shimaden.co.jp 03LGAT10300ILC
© Copyright 2024