the JFL213 Spec Sheet

JFL213 Specifications
2-WAY FULL-RANGE LOUDSPEAKER 110° × 15°
See NOTES TABULAR DATA for details
CONFIGURATION
Subsystem:
Transducer Loading
LF 2× 10 in cone HF 3× .75 in exit, 1.75 in voice coil Horn-loaded
compression driver
Vented
Operating Mode:
Amplifier Channels
Single-amp LF/HF Bi-amp LF,HF External Signal Processing
High pass filter
DSP w/2-way filters
PERFORMANCE
Operating Range: 65 Hz to 20 kHz
FEATURES
• Two-way, constant curvature line array module
• Compact and light; a “one-person lift”
• Easy to mount, fly or ground stack
• Two-module, pole-mounted arrays or up to five modules flown
• Classic EAW output, pattern control and fidelity
DESCRIPTION
The JFL213 compact, two-way line array module features a range of EAW’s
most innovative line array technologies within a mobile, light-weight package
appropriate in a wide range of small- to medium-sized venues. With its
companion subwoofer, the JFL118, this easy-to-use system solves problems in
both portable and permanently installed applications.
Nominal Beamwidth:
Horz110°
Vert15°
Axial Sensitivity (whole space SPL):
LF/HF 95 dB 65 Hz to 20 kHz
LF 96 dB 65 Hz to 1520 Hz
HF 102 dB 1320 Hz to 20 kHz
Input Impedance (ohms):
Nominal
Minimum
LF/HF 8 6.4 @ 200 Hz
LF 8 6.5 @ 630 Hz
HF 16 11.9 @ 20 kHz
High Pass Filter: High Pass =>60 Hz, 12 dB/octave Butterworth
Accelerated Life Test:
LF/HF 79.9 V 800 W @ 8 ohm
LF 79.9 V 800 W @ 8 ohm
The JFL213’s two-way design mounts dual 10-in cone transducers in an
optimally vented enclosure and spaced to extend pattern control into the
low frequency range. Three horn-loaded, 0.75-in exit / 1.75-in voice coil
compression drivers deliver even dispersion of high frequency information
over the entire 110° horizontal coverage area.
HF 35.7 V 80 W @ 16 ohm
EAW engineers optimized the JFL213’s size, shape and weight for easy transport
and setup by a single person, with side handles designed as part of the rigging
system and aligned with the enclosure’s center of balance. Users can mount up
to two JFL213s on a loudspeaker stand with a 35mm/1.38-in diameter pole. The
cleverly-designed, dual-angle pole mount cup allows the bottom enclosure to
be aimed 0° or -15°. (A two-module array with the lower modules aimed at -15°
aims the upper module at 0°.) The JFL118 features an integrated pole mount
cup, letting it serve as a large, stable base for pole mounting.
The JFL213’s ultra-strong rigging system allows users to hang up to five modules
with a 10:1 safety factor, which meets or exceeds all standards enforced
throughout the world. A single person can easily connect the modules to the
accessory FB221 Fly Bar as well as to each other. The FB221 also doubles as
a ground stack base for up to four JFL213s. For permanent installation, each
JFL213 provides a pair of M10 threaded mounting points.
Calculated Axial Output Limit (whole space SPL):
Average
Peak
LF/HF 124 dB
130 dB
LF 125 dB
131 dB
HF 124 dB 130 dB
ORDERING DATA
Description
Part Number
EAW JFL213 Black
2039855-90
EAW JFL213 White
2041840-90
Optional Accessories
Eye Bolt Forged Shoulder M10 X 1.5 X 37mm
0029818
Flybar JFL & HDA Black [FB221]
2036411
The JFL213 allows users to switch between single- or bi-amp powering modes.
The JFL213 delivers optimal performance when operated in bi-amp mode
with an EAW UX Series digital processor. In addition to the HF shading filters,
UX Series digital processor deliver EAW Focusing™ setting, which correct for
anomalies that occur in the time domain of any loudspeaker or transducer.
Enclosures are protected by our tough, scratch-resistant RoadCoat™ finish and
durable, foam-backed steel grilles protect the transducers. Six year warranty.
Eastern Acoustic Works | One Main Street | Whitinsville, MA 01588 USA | tel 800 992 5013 / +1 508 234 6158 | fax 508 234 8251 | www.eaw.com
EAW products are continually improved. All specifications are therefore subject to change without notice.
Part Number: RD0732 Rev C00
APR2015
EAW products are continually improved. All specifications are therefore subject to change without notice.
A
12.37 11.37
[314.2] [288.8]
TSC
B
POLE
MOUNT
CUPS
1
8.95
11.74 [227.3]
[298.1]
GRILLE
PARTIALLY
SHOWN
11.87
[301.5]
15.64 TSC
[397.2]
C
TOP
VIEW A-A
21.14[537.0]
FRONT
(24.84 [631.0])
0.18[4.5]
1
THIRD ANGLE PROJECTION
(X.XX) = REF DIMS
NO TOLERANCE IMPLIED
TOLERANCE IN INCHES
LINEAR ± 0.13 in / ± 3.3 mm
ANGLES ± 1°
UNLESS OTHERWISE SPECIFIED:
ALL DIMENSIONS ARE IN INCHES
DUAL [MM] DIMENSIONS
FOR REF ONLY
3
DIMENSIONS ACROSS CENTERLINES
TO BE SYMMETRICAL
4
INPUT
PANEL
5.0
[128]
A
PRO ENGINEER
A
B
C
ENCLOSURE
Material Exterior-grade Baltic birch plywood
Finish Wear resistant textured black paint
Grille Powder-coated perforated steel
Part Number: RD0732 Rev C00
2039856-CD-A_DWG_CUSTOMR_JFL213
4
REVISION:
0.088
SCALE:
2039856-CD
SHEET 1 OF 1
DRAWING NUMBER:
A
DWG CUSTOMER JFL213
[MECHANICAL SPECIFICATION]
BACK
DATE
9/17/12
www.eaw.com
JFL213
ECOWHT8923
19.41[493.0]
A
REV CHANGE NUMBER
TITLE:
10.43
[265.0]
TSC = THEORETICAL SHARP CORNER
RIGHT SIDE
A
6.89
[175.0]
2X HANDLES,
PROPRIETARY
RIGGING SYSTEM
DIMENSIONS APPLY
TO BOTH SIDES
6.22
[158.0]
THE INFORMATION CONTAINED
HEREIN IS PROPRIETARY AND
CONFIDENTIAL PROPERTY OF
LOUD TECHNOLOGIES, INC.
ALL RIGHTS RESERVED
A
6.39
[162.2]
15°
6.22
[158.0]
9.73
[247.3]
2
3
NOTES:
1. SYMBOL
INDICATES MOUNTING POINT,
M10 X 1.5 THREADED HOLE (PI ANGLE).
2. SYMBOL
INDICATES CENTER OF BALANCE.
3. WEIGHT APPROX. 62 lb [28 kg].
4. SHIPPING WEIGHT APPROX. 75 lb [34 kg].
2X STACK PAD ROUTS
2
JFL213 Specifications
NOTE: This drawing has been reduced. Do not scale.
Eastern Acoustic Works | One Main Street | Whitinsville, MA 01588 USA | tel 800 992 5013 / +1 508 234 6158 | fax 508 234 8251 | www.eaw.com
APR2015
JFL213 Specifications
PERFORMANCE DATA
See NOTES GRAPHIC DATA for details
Frequency Response: Processed
Frequency Response: Unprocessed Single-amp
Single Box = green, Multi Box = orange, Long Throw = black
10
120
0
110
-10
100
SPL (dB)
SPL (dB)
LF = green, HF = black, Complete = blue
-20
90
-30
80
-40
70
-50
10
100
1000
Frequency (Hz)
60
20000
Frequency Response: Unprocessed
10
100
1000
20000
Frequency (Hz)
Impedance
LF = green, HF = black, Complete = blue
LF = green, HF = black, Complete = blue
120
100
110
Ohms
SPL (dB)
100
90
10
80
70
60
10
100
1000
1
20000
10
Frequency (Hz)
Beamwidth
1000
Frequency (Hz)
20000
Phase Linearity
Horizontal = orangeVertical = black
Complete = blue
360
180
100
90
Degrees
Degrees
100
10
-0
-90
1
100
1000
20000
-180
10
Frequency (Hz)
100
1000
Frequency (Hz)
20000
Eastern Acoustic Works | One Main Street | Whitinsville, MA 01588 USA | tel 800 992 5013 / +1 508 234 6158 | fax 508 234 8251 | www.eaw.com
EAW products are continually improved. All specifications are therefore subject to change without notice.
Part Number: RD0732 Rev C00
APR2015
JFL213 Specifications
HORIZONTAL POLAR DATA
See NOTES GRAPHIC DATA for details
90˚
90˚
135˚
135˚
45˚
180˚
0˚
-135˚
100Hz
125Hz
160Hz
200Hz
45˚
180˚
-135˚
-45˚
-90˚
90˚
90˚
135˚
45˚
180˚
0˚
-135˚
250Hz
315Hz
400Hz
500Hz
45˚
180˚
-135˚
-45˚
-45˚
-90˚
-90˚
90˚
90˚
135˚
135˚
45˚
180˚
0˚
-135˚
-45˚
630Hz
800Hz
1000Hz
1250Hz
0˚
4000Hz
5000Hz
6300Hz
8000Hz
-45˚
-90˚
135˚
0˚
1600Hz
2000Hz
2500Hz
3150Hz
45˚
180˚
0˚
-135˚
-90˚
10000Hz
12500Hz
16000Hz
-45˚
-90˚
Eastern Acoustic Works | One Main Street | Whitinsville, MA 01588 USA | tel 800 992 5013 / +1 508 234 6158 | fax 508 234 8251 | www.eaw.com
EAW products are continually improved. All specifications are therefore subject to change without notice.
Part Number: RD0732 Rev C00
APR2015
JFL213 Specifications
VERTICAL POLAR DATA
See NOTES GRAPHIC DATA for details
90˚
90˚
135˚
135˚
45˚
180˚
0˚
-135˚
100Hz
125Hz
160Hz
200Hz
45˚
180˚
-135˚
-45˚
-90˚
90˚
90˚
135˚
45˚
180˚
0˚
-135˚
250Hz
315Hz
400Hz
500Hz
45˚
180˚
-135˚
-45˚
-45˚
-90˚
-90˚
90˚
90˚
135˚
135˚
45˚
180˚
0˚
-135˚
-45˚
630Hz
800Hz
1000Hz
1250Hz
0˚
4000Hz
5000Hz
6300Hz
8000Hz
-45˚
-90˚
135˚
0˚
1600Hz
2000Hz
2500Hz
3150Hz
45˚
180˚
0˚
-135˚
-90˚
10000Hz
12500Hz
16000Hz
-45˚
-90˚
Eastern Acoustic Works | One Main Street | Whitinsville, MA 01588 USA | tel 800 992 5013 / +1 508 234 6158 | fax 508 234 8251 | www.eaw.com
EAW products are continually improved. All specifications are therefore subject to change without notice.
Part Number: RD0732 Rev C00
APR2015
JFL213 Specifications
REVISIONS
INPUT PANEL
REV:
DESCRIPTION:
A00
NEW ISSUE PER ECOWHT8897 MJC
SIGNAL DIAGRAM
2-Way, Single-Amp (LF/HF)
NLT4MP
JFL213
SINGLE-AMP
PIN 1
PIN 1
PIN 2
PIN 2
HF
HPF
OPERATING MODE
AMP
XVR
BI-AMP
LF
NC
NC
BI-AMP
PIN 1
PIN 1
PIN 2
PIN 2
NLT4MP
LF
LF
HF
HF
SINGLE-AMP
HF SHADING
SINGLE-AMP
PIN 1
PIN 1
PIN 2
PIN 2
MULTI BOX
NC
NC
LF
LF
HF
HF
2-Way, Bi-Amp (LF, HF)
SINGLE BOX
BI-AMP
PIN 1
PIN 1
PIN 2
PIN 2
LONG THROW
DESIGNED IN WHITINSVILLE, MA, USA. MANUFACTURED IN CHINA. ©2012 LOUD
TECHNOLOGIES, INC. “EAW” IS A REGISTERED TRADEMARK OF LOUD TECHNOLOGIES, INC.
THIS PRODUCT HAS M10 MOUNTING POINTS. SEE OWNER’S MANUAL.
SERIAL NUMBER
REVISION
JFL213 = 30 KG / 65 LB
JFL213 RIGGING WORKING LOAD LIMIT (WLL): FIVE(5)
JFL213 IN SUCCESSION. 148 KG / 325LB
FAILURE TO FOLLOW MANUFACTURER’S
INSTRUCTIONS CAN RESULT
IN DAMAGE, INJURY, OR DEATH.
DSP
EQ
DELAY
HPF/LPF
OR
“EAW FOCUSING”
AMP
HF
AMP
LF
TITLE:
LOUD Technologies Inc.
LEGEND
ONE MAIN STREET, WHITINSVILLE, MA 01588 USA
HPF:
LPF:
LF/MF/HF:
AMP: XVR:
EAW Focusing:
ADOBE ILLUSTRATOR
DWG SPEC/INPUT JFL213
DRAWN BY:
MJC
DATE:
09/14/11
SCALE:
REV:
DRAWING NUMBER:
1:1
2038890-SD
LOUD TECHNOLOGIES INC, ALL RIGHTS RESERVED
High Pass Filter for crossover –or– Recommended High Pass Filter.
Low Pass Filter for crossover.
Low Frequency / Mid Frequency / High Frequency.
User Supplied Power Amplifier –or– Integral Amplifier for NT products.
Passive LPFs, HPFs, and EQ integral to the loudspeaker.
Digital Signal Processor capable of implementing EAW Focusing.
A00
SHEET:
1 of 1
NOTES
TABULAR DATA
1. Measurement/Data Processing Systems: Primary - FChart: proprietary EAW software; Secondary - Brüel & Kjær 2012.
2. Microphone Systems: Earthworks M30; Brüel & Kjær 4133
3. Measurements: Dual channel FFT; length: 32 768 samples; sample rate: 48 kHz; logarithmic sine wave sweep.
4. Measurement System Qualification (includes all uncertainties): SPL: accuracy +/-0.2 dB @ 1 kHz, precision +/-0.5 dB 20 Hz to 20 kHz, resolution 0.05 dB; Frequency: accuracy +/-1 %, precision +/-0.1 Hz, resolution the larger of 1.5 Hz or 1/48 octave; Time: accuracy +/-10.4 μs, precision +/-0.5 μs, resolution 10.4 μs; Angular: accuracy +/-1°, precision +/-0.5°, resolution 0.5°.
5. Environment: Measurements time-windowed and processed to eliminate room effects, approximating an anechoic environment. Data processed as anechoic or fractional space, as noted.
6. Measurement Distance: 7.46 m. Acoustic responses represent complex summation of the subsystems at 20 m. SPL is referenced to other distances using the Inverse Square Law.
7. Enclosure Orientation: For beamwidth and polar specifications, as shown in Mechanical Specification drawing.
8. Volts: Measured rms value of the test signal.
9. Watts: Per audio industry practice, “loudspeaker watts” are calculated as voltage squared divided by rated nominal impedance. Thus, these are not True Watt units of energy as defined
by International Standard.
10. SPL: (Sound Pressure Level) Equivalent to the average level of a signal referenced to 0 dB SPL = 20 microPascals.
11. Subsystem: This lists the transducer(s) and their acoustic loading for each passband. Sub = Subwoofer, LF = Low Frequency, MF = Mid Frequency, HF = High Frequency.
12. Operating Mode: User selectable configurations. Between system elements, a comma (,) = separate amplifier channels; a slash (/) = single amplifier channel. DSP = Digital Signal Processor.
IMPORTANT: To achieve the specified performance, the listed external signal processing must be used with EAW-provided settings.
13. Operating Range: Range where the processed Frequency Response stays within -10 dB SPL of the power averaged SPL within this range; measured on the geometric axis. Narrow band
dips are excepted.
14. Nominal Beamwidth: Design angle for the -6 dB SPL points, referenced to 0 dB SPL as the highest level.
15. Axial Sensitivity: Power averaged SPL over the Operating Range with an input voltage that would produce 1 W at the nominal impedance; measured with no external processing on the geometric axis, referenced to 1 m.
16. Nominal Impedance: Selected 4, 8, or 16 ohm resistance such that the minimum impedance point is no more than 20% below this resistance over the Operating Range.
17. Accelerated Life Test: Maximum test input voltage applied with an EIA-426B defined spectrum; measured with recommended signal processing and Recommended Protection Filter.
18. Calculated Axial Output Limit: Highest average and peak SPLs possible during the Accelerated Life Test. The Peak SPL represents the 2:1 (6 dB) crest factor of the Life Test signal.
19. High Pass Filter: This helps protect the loudspeaker from excessive input signal levels at frequencies below the Operating Range.
GRAPHIC DATA
1. Resolution: To remove insignificant fine details, 1/12 octave cepstral smoothing was applied to acoustic frequency responses and 1/3 octave cepstral smoothing was applied to the beamwidth and impedance data. Other graphs are plotted using raw data.
2. Frequency Responses: Variation in acoustic output level with frequency for a constant input signal. Processed: normalized to 0 dB SPL. Unprocessed inputs: 2 V (4 ohm nominal impedance), 2.83 V (8 ohm nominal impedance), or 4 V (16 ohm nominal impedance) referenced to a distance of 1 m.
3. Processor Response: The variation in output level with frequency for a constant input signal of 0.775 V = 0 dB reference.
4. Beamwidth: Average angle for each 1/3 octave frequency band where, starting from the rear of the loudspeaker, the output first reaches -6 dB SPL referenced to 0 dB SPL as the highest level. This method means the output may drop below -6 dB SPL within the beamwidth angle.
5. Impedance: Variation in impedance magnitude, in ohms, with frequency without regard to voltage/current phase. This means the impedance values may not be used to calculate True Watts (see 9 above).
6. Polar Data: Horizontal and vertical polar responses for each 1/3 octave frequency band 100 Hz to 16 kHz or Operating Range.
Eastern Acoustic Works | One Main Street | Whitinsville, MA 01588 USA | tel 800 992 5013 / +1 508 234 6158 | fax 508 234 8251 | www.eaw.com
EAW products are continually improved. All specifications are therefore subject to change without notice.
Part Number: RD0732 Rev C00
APR2015