.hmc equipments private limited.
Contact us : +91 7752 323755,261202, 261015/ +91 94252 19536
Auto Control Dust Suppression Unit ‐ Code‐100
.hmc. code‐100 Auto‐Fog Dust Suppression System operates without compressed air at pressure ranging upto maximum 105 bar
.hmc "Auto
Auto‐Fog
Fog Dust Suppresion
.hmc. AUTOFOG Dust Suppression System operates
without compress air at high pressure ranging from
minimum
35
bar
to
maximum
105
bar,
(auto controlled ‐code‐100).Water is atomized into a mist
of microscopic particles as small as 10 micron with the
use of selective range of nozzle placed at pre set location
to discharge atomized water, these droplets join with the
airborne dust, increasing weight and help the combined
particle settles back into the main material stream.
Only minimal water is added to avoid material degradation. With the micro small droplet size and the
fog’s effective dispersal pattern, moisture addition is approximately 0.1% by weight of material conveyed.
.hmc. AUTOFOG Dust Suppression System eliminates fugitive dust emissions from material handling
and processing
• 0.1% addition of moisture on material
• No need of expensive compressed air
(No electric power consumption)
.hmc.
hmc Conflow code-100
code 100 Dust Suppression System
• No need of extra air line with water
connection
•Zero maintenance against compressed air
DRY FOG System
y
•Zero maintenance against electrical
conventional Dust Suppression system
•100 % atomization
•Mechanical sensing unit (100% fail–proof)
•ZERO OPERATING COST
•Operates at belts speed from 100 to 750 ft
/min
eliminates fugitive dust emissions from material handling and processing.
Supplying dust suppression water onto conveyor belts transporting
minerals, particularly at a transfer point, where one conveyor
discharges its contents onto a second belt, and dust is often created.
Composite
p
Set: Code 100 / Strainer,, SS spray
p y bar & nozzle,, safetyy relief valve,,
high pressure pump, high pressure hosepipe.
Zero
Service
Maintanance
DUST SUPPRESSION & FOGGING SYSTEM
Controlling Environment
.hmc equipments private limited.
Contact us : +91 7752 408406 / 412702, +91 94252 19536
.hmc. AUTOFOG Dust Suppression System operates without compressed air at high pressure
ranging from minimum 35 bar to maximum 105 bar,(auto controlled –Conflow-code-100)
Water is atomized into a mist of microscopic particles as small as 10 micron with the use of selective
range
g of nozzle p
placed at p
pre set location to discharge
g atomized water, these droplets
p
jjoin with the
airborne dust, increasing weight and help the combined particle settles back into the main material
stream.
Only minimal water is added to avoid material degradation. With the micro small droplet size and the
fog’s effective dispersal pattern, moisture addition is approximately 0.1% by weight of material conveyed.
.hmc. AUTOFOG Dust Suppression System eliminates fugitive dust emissions from material handling
and processing.
Few important advantages:
•
•
•
•
•
•
•
•
•
•
0.1% addition of moisture on material
No need of expensive compressed air (save huge expenses)
No need of extra air line with water connection
Zero maintenance against compressed DRY FOG system
Z
Zero
maintenance
i t
against
i t electrical
l t i l conventional
ti
l dust
d t suppression
i
system
t
100 % atomization
Mechanical sensing unit (100% fail–proof)
ZERO OPERATING COST (No energy power consumption)
Operates at belts speed from 100FT/MIN to 750 FT/MIN
Maximum working pressure min 35 bar to max 105 bar
.hmc. Conflow code-100 Dust Suppression System eliminates fugitive dust emissions from material
handling and processing.
Typical Applications:Supplying dust suppression water onto conveyor belts transporting minerals, particularly at a
transfer point, where one conveyor discharges its contents onto a second belt, and dust is often
created.
Zero
Service
Maintanance
DUST SUPPRESSION & FOGGING SYSTEM
Controlling Environment