Full control over time, quality, reliability and costs The best generation ever of Klepter ® Klepter C1 TE Klepter C2 TE Klepter FLEX C2 TE S1 Klepter SUPERFIX C2 TE S2 Klepter UNIFIX Klepter ISOFIX EPS XPS MW Klepter GAZOBETON Klepter TURBOZOL 1 ВИСОКОКАЧЕСТВЕНИ ЛЕПИЛА С ФИБРИ BG EN DE BG EN DE BG EN DE С1 С1 С1 ЛЕПИЛО ЗА ФАЯНС ТЕРАКОТА ЗА ВЪТРЕШНА УПОТРЕБА BG EN FAIENCE TERRACOTTA GRANITFLIESE KLEBER FÜR DEN INNENBEREICH DE МРАМОР ТЕРАКОТА ГРАНИТ ФАЯНС КАМЪК ПЛУВНИ БАСЕЙНИ BG MARBLE TERRAKOTTA GRANITE FAIENCE TILES STONE SWIMMING POOLS EN MARMOR STEINE GRANITE TERRAKOTTA KERAMIKFLIESEN FLIESEN AUF FLIESEN DE ЛЕПИЛО ЗА ШПАКЛОВКА С ФИБРИ BG ADHESIVE PUTTY MIXTURE WITH FIBERS EN KLEBERSTOFF FÜR SPACHTELMASSE MIT FASERN DE GAZOBETON EN GAZOBETON DE GAZOBETON BG ГРАНИТОГРЕС HOCHWERTIGEN KLEBSTOFFEN MIT FASER FAIENCE TERRACOTTA GRANITE TILE ADHESIVE FOR INDOOR USE SUREPFIX SUREPFIX SUREPFIX UNIFIX UNIFIX UNIFIX HIGH QUALITY ADHESIVES WITH FIBER ЛЕПИЛО ЗА ГАЗОБЕТОННИ БЛОКЧЕТА BG GAS CONCRETE BLOCKS ADHESIVE EN DE KLEBERSTOFF FÜR GASBETONBLÖCKE www.klepter.com C2 C2 C2 ЛЕПИЛО ЗА ФАЯНС ТЕРАКОТА ЗА ВЪНШНА УПОТРЕБА ГРАНИТОГРЕС FAIENCE TERRACOTTA GRANITE TILE ADHESIVE FOR OUTDOOR USE KLEBERSTOFF FÜR KERAMIK TERRAKOTTA GRANITFLIESEN FÜR AUSSENANWENDUNG FLEX FLEX FLEX ISOFIX ISOFIX ISOFIX ЛЕПИЛО ЗА ТЕРАКОТ ГРАНИТОГРЕС ФАЯНС КАМЪК ПЛОЧКА ВЪРХУ ПЛОЧКА ADHESIVE TERRAKOTTA GRANITE FAIENCE TILES STONE TILE ON TILE KLEBERSTOFF TERRAKOTTA GRANITE KERAMIKFLIESEN STEINE FLIESEN AUF FLIESEN ЗА ЛЕПЕНЕ НА ИЗОЛАЦИОННИ ПЛОСКОСТИ ОТ EPS И XPS EPS AND XPS INSULATION BOARD ADHESIVE FÜR VERKLEBUNG VON DÄMMPLATTEN EPS UND XPS TURBOSOL TURBOSOL TURBOSOL ВАРОЦИМЕНТОВА МАЗИЛКА ЗА МАШИННО НАНАСЯНЕ PLASTER FOR MACHINE APPLICATION PFLASTER FÜR MASCHINENANWENDUNG C1 GB Class C1 TE to PRODUCT: CEMENTITIOUS TILE ADHESIVE WITH FIBRES, CLASS C1 TE in compliance with the requirements of standard EN 12004. for laying of ceramic tiles (terracotta), Granitogres (fine stoneware tiles), marble, tile on tile. COMPOSITION: Portland cement, fractionated quartz sand, polymer additives, fibers. APPLICATION: For adhesion of porous ceramic tiles on concrete, cement plasters, and other mineral substrates in dry and humid places indoors. It is suitable for adhesion of tiles with dimensions up to 30 x 30 cm to vertical and horizontal surfaces. PROPERTIES: Good strength, enough open time, decreased slipping when laid on vertical substrates, water- and cold resistant. PREPARATION OF THE SUBSTRATE: the substrate must be clean, dry and sound, without cracks. Primer must be applied beforehand on highly absorbent surfaces. PREPARATION OF THE MIXTURE: Mix a bag of 25 kg of adhesive with 5,5 L of water. In a suitable container add the dry mix to the required quantity of water and mix with a mixing device until a homogeneous consistency is attained. Leave the mixture to stay for 10 min., then mix again and the product is ready to use. LAYING: Apply the adhesive with a square notch trowel with notch size from 4 x 4 mm to 8 x 8 mm depending on the size of the tile. First apply a thin contact layer on the substrate and then using the notched side of the trowel, comb out the still fresh adhesive. Lay and press the tiles on the fresh adhesive. When laying non-porous tiles, tiles with large sizes, or laying tile on tile, apply adhesive on the substrate and on the back of the tile – this will guarantee maximum adhesion between the tile and the adhesive. FIBER ELASTIC EASY TO USE MAIN PROPERTIES PERFORMANCE FEATURES STANDARD/ VALIDATION METHOD BDS EN 1348 High early tensile adhesion strength ≥ 0,5 N/mm2 High tensile adhesion strength after immersion in water ≥ 0,5 N/mm2 High tensile adhesion strength after heat treatment ≥ 0,5 N/mm2 BDS EN 1348 High tensile adhesion strength after 25 cycles of freezing/defrosting ≥ 0,5 N/mm2 BDS EN 1348 ≥ 0,5 N/mm2 after 20 min. BDS EN 1346 ≤ 0,5 mm2 BDS EN 1308 BDS EN 1348 Open time. Tensile adhesion strength Slipping Н 315 - May cause skin irritation. Н 317 - May cause allergic skin reaction. Н 318 - Causes serious eye damage. Н 335 - May cause respiratory irritation. P261 – Avoid breathing dust. P271 – Use only outdoors or in a well-ventilated area. P304 + P340 – If inhaled: move the person to fresh air P312 – Call a poison center if you feel unwell. P302 + P352 - If on skin – wash with plenty of water. P280 – Wear protective gloves, protective clothing, and protective glasses. P332 + P313 – If skin irritation occurs, seek medical care. P305 + P351 + P338 – If in eyes – wash carefully with water for several minutes. Remove eye lenses, if any, and keep on washing. P333 + P 313 – If a skin irritation or a rash occurs – seek medical advice. RECOMMENDATION: Addition of other materials in the ready mixture is not allowed. The recommended temperature range of use is from +5°C to + 35°C. CONSUMPTION RATE: from 2 kg/m2 to 5 kg/m2 depending on the size of the notches of the square trowel and how even the surface is. STORAGE: To be kept in a dry and well ventilated place. C2 GB Class C2 TE to PRODUCT: CEMENTITIOUS TILE ADHESIVE WITH FIBRES, CLASS C2TE in compliance with the requirements of standard EN 12004. for laying of ceramic tiles (terracotta), Granitogres (fine stoneware tiles), marble, tile on tile. COMPOSITION: Portland cement, granulated quartz mix, polymer additives, fibers. APPLICATION: High quality cementitious adhesive for outdoor and indoor application, for thin-bed applying on ceramic tiles, natural stones and Granitogres, for adhesion in cases of increased load, hydro insulated floors and walls in wet rooms. Suitable for vertical and horizontal substrates. PROPERTIES: Improved strength, increased open time, decreased slipping when laid on vertical substrates, water- and cold resistant. PREPARATION OF THE SUBSTRATE: the substrate must be clean, dry and sound, without cracks. Primer must be applied beforehand on highly absorbent surfaces. PREPARATION OF THE MIXTURE: Mix a bag of 25 kg of adhesive with 5,5 L of water. In a suitable container add the dry mix to the required quantity of water and mix with a mixing device until a homogeneous consistency is attained. Leave the mixture to stay for 10 min., then mix again and the product is ready to use. LAYING: Apply the adhesive with a square notch trowel with notch size from 4 x 4 mm to 8 x 8 mm depending on the size of the tile. First apply a thin contact layer on the substrate and then using the notched side of the trowel, comb out the still fresh adhesive. Lay and press the tiles on the fresh adhesive. When laying non-porous tiles, tiles with large sizes, or laying tile on tile, apply adhesive on the substrate and on the back of the tile – this will guarantee maximum adhesion between the tile and the adhesive. FIBER ELASTIC EASY TO USE PERFORMANCE FEATURES STANDARD/ VALIDATION METHOD High early tensile adhesion strength ≥ 1 N/mm2 BDS EN 1346 High tensile adhesion strength after immersion in water ≥ 1 N/mm2 BDS EN 1346 High tensile adhesion strength after heat treatment ≥ 1 N/mm2 BDS EN 1346 High tensile adhesion strength after 25 cycles of freezing/defrosting ≥ 1 N/mm BDS EN 1346 ≥ 0,5 N/mm2 after 30 min. BDS EN 1346 ≤ 0,5 mm2 BDS EN 1308 MAIN PROPERTIES Open time. Tensile adhesion strength Slipping 2 Н 315 - May cause skin irritation. Н 317 - May cause allergic skin reaction. Н 318 - Causes serious eye damage. Н 335 - May cause respiratory irritation. P261 – Avoid breathing dust. P271 – Use only outdoors or in a well-ventilated area. P304 + P340 – If inhaled: move the person to fresh air P312 – Call a poison center if you feel unwell. P302 + P352 - If on skin – wash with plenty of water. P280 – Wear protective gloves, protective clothing, and protective glasses. P332 + P313 – If skin irritation occurs, seek medical care. P305 + P351 + P338 – If in eyes – wash carefully with water for several minutes. Remove eye lenses, if any, and keep on washing. P333 + P 313 – If a skin irritation or a rash occurs – seek medical advice. RECOMMENDATION: Addition of other materials in the ready mixture is not allowed. The recommended temperature range of use is from +5°C to + 35°C. CONSUMPTION RATE: from 2 kg/m2 to 5 kg/m2 depending on the size of the notches of the square trowel and how even the surface is. STORAGE: To be kept in a dry and well ventilated place. FLEX GB Class C2 TE S1 to PRODUCT: ELASTIC CEMENTITIOUS TILE ADHESIVE WITH FIBRES, CLASS C2TE S1 in compliance with the requirements of standards EN 12004 and EN 12002. for laying of ceramic tiles (terracotta), Granitogres (fine stoneware tiles), marble, tile on tile. COMPOSITION: Portland cement, fractionated quartz sand, polymer additives, fibers. APPLICATION: High quality elastic construction adhesive for outdoor and indoor application, for thin-bed applying on ceramic tiles, natural stones and Granitogres, for adhesion in cases of increased load, over underfloor heating, and hydro insulated floors. Suitable for vertical and horizontal substrates and large tiles. PROPERTIES: Improved strength, increased open time, decreased slipping when laid on vertical substrates, water- and cold resistant. PREPARATION OF THE SUBSTRATE: the substrate must be clean, dry and sound, without cracks. Primer must be applied beforehand on highly absorbent surfaces. PREPARATION OF THE MIXTURE: Mix a bag of 25 kg of adhesive with 5,5 L of water. In a suitable container add the dry mix to the required quantity of water and mix with a mixing device until a homogeneous consistency is attained. Leave the mixture to stay for 10 min., then mix again and the product is ready to use. LAYING: Apply the adhesive with a square notch trowel with notch size from 4 x 4 mm to 8 x 8 mm depending on the size of the tile. First apply a thin contact layer on the substrate and then using the notched side of the trowel, comb out the still fresh adhesive. Lay and press the tiles on the fresh adhesive. When laying non-porous tiles, tiles with large sizes, or laying tile on tile, apply adhesive on the substrate and on the back of the tile – this will guarantee maximum adhesion between the tile and the adhesive. FIBER ELASTIC EASY TO USE High early tensile adhesion strength ≥ 1 N/mm2 STANDARD/ VALIDATION METHOD BDS EN 1348 High tensile adhesion strength after immersion in water ≥ 1 N/mm2 BDS EN 1348 High tensile adhesion strength after heat treatment ≥ 1 N/mm2 BDS EN 1348 High tensile adhesion strength after 25 cycles of freezing/defrosting ≥ 1 N/mm2 BDS EN 1348 ≥ 0,5 N/mm2 after 30 min. BDS EN 1346 ≤ 0,5 mm2 BDS EN 1308 ≥ 2,5 mm and < 5mm BDS EN 12002 MAIN PROPERTIES Open time. Tensile adhesion strength Slipping Transverse deformation PERFORMANCE FEATURES Н 315 - May cause skin irritation. Н 317 - May cause allergic skin reaction. Н 318 - Causes serious eye damage. Н 335 - May cause respiratory irritation. P261 – Avoid breathing dust. P271 – Use only outdoors or in a well-ventilated area. P304 + P340 – If inhaled: move the person to fresh air P312 – Call a poison center if you feel unwell. P302 + P352 - If on skin – wash with plenty of water. P280 – Wear protective gloves, protective clothing, and protective glasses. P332 + P313 – If skin irritation occurs, seek medical care. P305 + P351 + P338 – If in eyes – wash carefully with water for several minutes. Remove eye lenses, if any, and keep on washing. P333 + P 313 – If a skin irritation or a rash occurs – seek medical advice. RECOMMENDATION: Addition of other materials in the ready mixture is not allowed. The recommended temperature range of use is from +5°C to + 35°C. CONSUMPTION RATE: from 2 kg/m2 to 5 kg/m2 depending on the size of the notches of the square trowel and how even the surface is. STORAGE: To be kept in a dry and well ventilated place. SUPERFIX GB Class C2 TE S2 to TYPE: HIGHLY FLEXIBLE CEMENTITIOUS TILE ADHESIVE WITH FIBRES, CLASS C2TES2 in compliance with the requirements of standard EN 12004 and EN12002. COMPOSITION: Portland cement, fractionated quartz sand, polymer additives, fibers. APPLICATION: Adhesive with high elasticity after hardening for adhesion of ceramic tiles, granitogres, and glass mosaics. It ensures flexible adhesive layer which absorbs the inner tension in the deformable and critical substrates and prevents the tiles from coming off. It is suitable for laying on preliminary prepared substrates of drywall and wooden materials, and for the lining of swimming pools with glass tiles in a combination with water insulation materials. For tiling of heavy duty facades and places. PROPERTIES: Super flexible – class S2 as per EN 12002, excellent for tiling of swimming pools and facades; decreased slipping when laid on vertical substrates, water- and freeze resistant. PREPARATION OF THE SUBSTRATE: the substrate must be clean, dry and sound, without cracks. Primer must be applied beforehand on highly absorbent surfaces. PREPARATION OF THE MIXTURE: Mix a bag of 25 kg of adhesive with 5,5 L of water. In a suitable container add the dry mix to the required quantity of water and mix with a mixing device until a homogeneous consistency is attained. Leave the mixture to stay for 10 min., then mix again and the product is ready to use. LAYING: Apply the adhesive with a square notch trowel with notch size from 4 x 4 mm to 8 x 8 mm depending on the size of the tile. First apply a thin contact layer on the substrate and then using the notched side of the trowel, comb out the still fresh adhesive. Lay and press the tiles on the fresh adhesive. When laying non-porous tiles, tiles with large sizes, or laying tile on tile, apply adhesive on the substrate and on the back of the tile – this will guarantee maximum adhesion between the tile and the adhesive. FIBER ELASTIC EASY TO USE PERFORMANCE FEATURES STANDARD/ VALIDATION METHOD High early tensile adhesion strength ≥ 1 N/mm2 BDS EN 1346 High tensile adhesion strength after immersion in water ≥ 1 N/mm2 BDS EN 1346 High tensile adhesion strength after heat treatment ≥ 1 N/mm2 BDS EN 1346 High tensile adhesion strength after 25 cycles of freezing/defrosting ≥ 1 N/mm BDS EN 1346 ≥ 0,5 N/mm2 after 30 min. BDS EN 1346 ≤ 0,5 mm2 BDS EN 1308 MAIN PROPERTIES Open time. Tensile adhesion strength Slipping 2 Н 315 - May cause skin irritation. Н 317 - May cause allergic skin reaction. Н 318 - Causes serious eye damage. Н 335 - May cause respiratory irritation. P261 – Avoid breathing dust. P271 – Use only outdoors or in a well-ventilated area. P304 + P340 – If inhaled: move the person to fresh air P312 – Call a poison center if you feel unwell. P302 + P352 - If on skin – wash with plenty of water. P280 – Wear protective gloves, protective clothing, and protective glasses. P332 + P313 – If skin irritation occurs, seek medical care. P305 + P351 + P338 – If in eyes – wash carefully with water for several minutes. Remove eye lenses, if any, and keep on washing. P333 + P 313 – If a skin irritation or a rash occurs – seek medical advice. RECOMMENDATION: Addition of other materials in the ready mixture is not allowed. The recommended temperature range of use is from +5°C to + 35°C. CONSUMPTION RATE: from 2 kg/m2 to 5 kg/m2 depending on the size of the notches of the square trowel and how even the surface is. STORAGE: To be kept in a dry and well ventilated place. ISOFIX GB PRODUCT: ADHESIVE AND PLASTER FOR HEAT INSULATION COMPOSITION: Portland cement, fractionated quartz sand, polymer additives, fibers. APPLICATION: For adhesion of EPS and XPS insulation boards and application of plaster for the installation of reinforcing fiber mesh. Suitable for installation of external wall insulation systems on new buildings as well as improvement of the heat insulation of old walls and facades. PROPERTIES: High strength, excellent adhesion to the substrate, polystyrene boards and reinforcing mesh, high vapor-permeability, water- and freeze resistant. The plaster protects the insulation layer and guarantees water resistance and crack resistance of the applied finish coat. PREPARATION OF THE SUBSTRATE: the substrate must be dry, sound, well cleaned of dust and dirt. Primer must be applied beforehand on highly absorbent surfaces. PREPARATION OF THE MIXTURE: Mix a bag of 25 kg of adhesive with 5,5 L of water. In a suitable container add the dry mix to the required quantity of water and mix with a mixing set for 10 min., then mix again and the product is ready to use. The ready mixture can be used within 60 minutes. FIBER ELASTIC EASY TO USE MAIN PROPERTIES PERFORMANCE STANDARD/ FEATURES VALIDATION METHOD BDS 172 1300 kg/m² Bulk density Dry extract contents at 105°C 99,59/0,41% Ash contents at 450°C 97.06/2.94% BDS EN13820 Density in hardened state 1620 kg/m² BDS EN1015-10 Compressive strength BDS EN 196-2 14.4 N/mm2 BDS EN 1015-11 Bending strength 4.1 N/mm2 BDS EN 1015-11 Tensile adhesion strength with the substrate (concrete surface) Tensile adhesion strength of the main coat (with the reinforcement) EPS board 1090 kPa BDS EN 1015-12 170 kPa BDS 13494 Tensile adhesion strength of the adhesion and plaster mortar with EPS boards: - after 28 days at normal conditions - after 3 cycles of conditioning 180 kPa 200 kPa BDS 13494 Capillary water absorption coefficient - c 0.006 kg/m2.h0,5 Cat. W2 c≤ 0.2 BDS EN 1015-18 APPLYING: If the substrate is smooth and even, apply the ready mixture on the whole surface of the insulation board with a square notch trowel forming ridges with the notched side of the trowel. If the substrate is uneven, apply the adhesive on the circumference of the insulation board forming a 4-5 cm wide strip, and apply “balls” of the ready mixture at several places inside this strip. When making reinforced plaster, apply the mixture on the surface of the substrate using the notched side of the trowel, apply the mesh overlapping the mesh pieces at the joints, press the mesh into the fresh mixture and smooth the surface with the trowel making the mesh invisible. Н 315 - May cause skin irritation. Н 317 - May cause allergic skin reaction. Н 318 - Causes serious eye damage. Н 335 - May cause respiratory irritation. P261 – Avoid breathing dust. P271 – Use only outdoors or in a well-ventilated area. P304 + P340 – If inhaled: move the person to fresh air P312 – Call a poison center if you feel unwell. P302 + P352 - If on skin – wash with plenty of water. P280 – Wear protective gloves, protective clothing, and protective glasses. P332 + P313 – If skin irritation occurs, seek medical care. P305 + P351 + P338 – If in eyes – wash carefully with water for several minutes. Remove eye lenses, if any, and keep on washing. P333 + P 313 – If a skin irritation or a rash occurs – seek medical advice. RECOMMENDATION: Addition of other materials in the ready mixture is not allowed. The recommended temperature range of use is from +5°C to + 35°C. CONSUMPTION RATE: For adhesion: from 4,0 kg/m2 to 5,5 kg/m2 depending on the size of the notches of the square trowel and how even the surface is. For plastering: from 4,0 kg/m2 to 5,0 kg/m2 STORAGE: To be kept in a dry and well ventilated place. UNIFIX GB PRODUCT: ADHESIVE AND PLASTER FOR HEAT INSULATION COMPOSITION: Portland cement, fractionated quartz sand, polymer additives, fibers. APPLICATION: For adhesion of EPS and XPS insulation boards and application of plaster for the installation of reinforcing fiber mesh. Suitable for installation of external wall insulation systems on new buildings as well as improvement of the heat insulation of old walls and facades. PROPERTIES: High strength, excellent adhesion to the substrate, polystyrene boards and reinforcing mesh, high vapor-permeability, water- and freeze resistant. The plaster protects the insulation layer and guarantees water resistance and crack resistance of the applied finish coat. PREPARATION OF THE SUBSTRATE: the substrate must be dry, sound, well cleaned of dust and dirt. Primer must be applied beforehand on highly absorbent surfaces. PREPARATION OF THE MIXTURE: Mix a bag of 25 kg of adhesive with 5,5 L of water. In a suitable container add the dry mix to the required quantity of water and mix with a mixing set for 10 min., then mix again and the product is ready to use. The ready mixture can be used within 60 minutes. FIBER ELASTIC EASY TO USE MAIN PROPERTIES Bulk density PERFORMANCE STANDARD/ FEATURES VALIDATION METHOD BDS 172 1300 kg/m² Dry extract contents at 105°C 99,59/0,41% Ash contents at 450°C 97.06/2.94% BDS EN13820 Density in hardened state 1620 kg/m² BDS EN1015-10 Compressive strength BDS EN 196-2 14.4 N/mm2 BDS EN 1015-11 Bending strength 4.1 N/mm2 BDS EN 1015-11 Tensile adhesion strength with the substrate (concrete surface) Tensile adhesion strength of the main coat (with the reinforcement) EPS board 1090 kPa BDS EN 1015-12 170 kPa BDS 13494 Tensile adhesion strength of the adhesion and plaster mortar with EPS boards: - after 28 days at normal conditions - after 3 cycles of conditioning 180 kPa 200 kPa BDS 13494 Capillary water absorption coefficient - c 0.006 kg/m2.h0,5 Cat. W2 c≤ 0.2 BDS EN 1015-18 APPLYING: If the substrate is smooth and even, apply the ready mixture on the whole surface of the insulation board with a square notch trowel forming ridges with the notched side of the trowel. If the substrate is uneven, apply the adhesive on the circumference of the insulation board forming a 4-5 cm wide strip, and apply “balls” of the ready mixture at several places inside this strip. When making reinforced plaster, apply the mixture on the surface of the substrate using the notched side of the trowel, apply the mesh overlapping the mesh pieces at the joints, press the mesh into the fresh mixture and smooth the surface with the trowel making the mesh invisible. Н 315 - May cause skin irritation. Н 317 - May cause allergic skin reaction. Н 318 - Causes serious eye damage. Н 335 - May cause respiratory irritation. P261 – Avoid breathing dust. P271 – Use only outdoors or in a well-ventilated area. P304 + P340 – If inhaled: move the person to fresh air P312 – Call a poison center if you feel unwell. P302 + P352 - If on skin – wash with plenty of water. P280 – Wear protective gloves, protective clothing, and protective glasses. P332 + P313 – If skin irritation occurs, seek medical care. P305 + P351 + P338 – If in eyes – wash carefully with water for several minutes. Remove eye lenses, if any, and keep on washing. P333 + P 313 – If a skin irritation or a rash occurs – seek medical advice. RECOMMENDATION: Addition of other materials in the ready mixture is not allowed. The recommended temperature range of use is from +5°C to + 35°C. CONSUMPTION RATE: For adhesion: from 4,0 kg/m2 to 5,5 kg/m2 depending on the size of the notches of the square trowel and how even the surface is. For plastering: from 4,0 kg/m2 to 5,0 kg/m2 STORAGE: To be kept in a dry and well ventilated place. ISOFIX GB PRODUCT: ADHESIVE AND PLASTER FOR HEAT INSULATION COMPOSITION: Portland cement, fractionated quartz sand, polymer additives, fibers. APPLICATION: For adhesion of EPS and XPS insulation boards and application of plaster for the installation of reinforcing fiber mesh. Suitable for installation of external wall insulation systems on new buildings as well as improvement of the heat insulation of old walls and facades. PROPERTIES: High strength, excellent adhesion to the substrate, polystyrene boards and reinforcing mesh, high vapor-permeability, water- and freeze resistant. The plaster protects the insulation layer and guarantees water resistance and crack resistance of the applied finish coat. PREPARATION OF THE SUBSTRATE: the substrate must be dry, sound, well cleaned of dust and dirt. Primer must be applied beforehand on highly absorbent surfaces. PREPARATION OF THE MIXTURE: Mix a bag of 25 kg of adhesive with 5,5 L of water. In a suitable container add the dry mix to the required quantity of water and mix with a mixing set for 10 min., then mix again and the product is ready to use. The ready mixture can be used within 60 minutes. FIBER ELASTIC EASY TO USE MAIN PROPERTIES PERFORMANCE STANDARD/ FEATURES VALIDATION METHOD BDS 172 1300 kg/m² Bulk density Dry extract contents at 105°C 99,59/0,41% Ash contents at 450°C 97.06/2.94% BDS EN13820 Density in hardened state 1620 kg/m² BDS EN1015-10 Compressive strength BDS EN 196-2 14.4 N/mm2 BDS EN 1015-11 Bending strength 4.1 N/mm2 BDS EN 1015-11 Tensile adhesion strength with the substrate (concrete surface) Tensile adhesion strength of the main coat (with the reinforcement) EPS board 1090 kPa BDS EN 1015-12 170 kPa BDS 13494 Tensile adhesion strength of the adhesion and plaster mortar with EPS boards: - after 28 days at normal conditions - after 3 cycles of conditioning 180 kPa 200 kPa BDS 13494 Capillary water absorption coefficient - c 0.006 kg/m2.h0,5 Cat. W2 c≤ 0.2 BDS EN 1015-18 APPLYING: If the substrate is smooth and even, apply the ready mixture on the whole surface of the insulation board with a square notch trowel forming ridges with the notched side of the trowel. If the substrate is uneven, apply the adhesive on the circumference of the insulation board forming a 4-5 cm wide strip, and apply “balls” of the ready mixture at several places inside this strip. When making reinforced plaster, apply the mixture on the surface of the substrate using the notched side of the trowel, apply the mesh overlapping the mesh pieces at the joints, press the mesh into the fresh mixture and smooth the surface with the trowel making the mesh invisible. Н 315 - May cause skin irritation. Н 317 - May cause allergic skin reaction. Н 318 - Causes serious eye damage. Н 335 - May cause respiratory irritation. P261 – Avoid breathing dust. P271 – Use only outdoors or in a well-ventilated area. P304 + P340 – If inhaled: move the person to fresh air P312 – Call a poison center if you feel unwell. P302 + P352 - If on skin – wash with plenty of water. P280 – Wear protective gloves, protective clothing, and protective glasses. P332 + P313 – If skin irritation occurs, seek medical care. P305 + P351 + P338 – If in eyes – wash carefully with water for several minutes. Remove eye lenses, if any, and keep on washing. P333 + P 313 – If a skin irritation or a rash occurs – seek medical advice. RECOMMENDATION: Addition of other materials in the ready mixture is not allowed. The recommended temperature range of use is from +5°C to + 35°C. CONSUMPTION RATE: For adhesion: from 4,0 kg/m2 to 5,5 kg/m2 depending on the size of the notches of the square trowel and how even the surface is. For plastering: from 4,0 kg/m2 to 5,0 kg/m2 STORAGE: To be kept in a dry and well ventilated place. UNIFIX GB PRODUCT: ADHESIVE AND PLASTER FOR HEAT INSULATION COMPOSITION: Portland cement, fractionated quartz sand, polymer additives, fibers. APPLICATION: For adhesion of EPS and XPS insulation boards and application of plaster for the installation of reinforcing fiber mesh. Suitable for installation of external wall insulation systems on new buildings as well as improvement of the heat insulation of old walls and facades. PROPERTIES: High strength, excellent adhesion to the substrate, polystyrene boards and reinforcing mesh, high vapor-permeability, water- and freeze resistant. The plaster protects the insulation layer and guarantees water resistance and crack resistance of the applied finish coat. PREPARATION OF THE SUBSTRATE: the substrate must be dry, sound, well cleaned of dust and dirt. Primer must be applied beforehand on highly absorbent surfaces. PREPARATION OF THE MIXTURE: Mix a bag of 25 kg of adhesive with 5,5 L of water. In a suitable container add the dry mix to the required quantity of water and mix with a mixing set for 10 min., then mix again and the product is ready to use. The ready mixture can be used within 60 minutes. FIBER ELASTIC EASY TO USE MAIN PROPERTIES Bulk density PERFORMANCE STANDARD/ FEATURES VALIDATION METHOD BDS 172 1300 kg/m² Dry extract contents at 105°C 99,59/0,41% Ash contents at 450°C 97.06/2.94% BDS EN13820 Density in hardened state 1620 kg/m² BDS EN1015-10 Compressive strength BDS EN 196-2 14.4 N/mm2 BDS EN 1015-11 Bending strength 4.1 N/mm2 BDS EN 1015-11 Tensile adhesion strength with the substrate (concrete surface) Tensile adhesion strength of the main coat (with the reinforcement) EPS board 1090 kPa BDS EN 1015-12 170 kPa BDS 13494 Tensile adhesion strength of the adhesion and plaster mortar with EPS boards: - after 28 days at normal conditions - after 3 cycles of conditioning 180 kPa 200 kPa BDS 13494 Capillary water absorption coefficient - c 0.006 kg/m2.h0,5 Cat. W2 c≤ 0.2 BDS EN 1015-18 APPLYING: If the substrate is smooth and even, apply the ready mixture on the whole surface of the insulation board with a square notch trowel forming ridges with the notched side of the trowel. If the substrate is uneven, apply the adhesive on the circumference of the insulation board forming a 4-5 cm wide strip, and apply “balls” of the ready mixture at several places inside this strip. When making reinforced plaster, apply the mixture on the surface of the substrate using the notched side of the trowel, apply the mesh overlapping the mesh pieces at the joints, press the mesh into the fresh mixture and smooth the surface with the trowel making the mesh invisible. Н 315 - May cause skin irritation. Н 317 - May cause allergic skin reaction. Н 318 - Causes serious eye damage. Н 335 - May cause respiratory irritation. P261 – Avoid breathing dust. P271 – Use only outdoors or in a well-ventilated area. P304 + P340 – If inhaled: move the person to fresh air P312 – Call a poison center if you feel unwell. P302 + P352 - If on skin – wash with plenty of water. P280 – Wear protective gloves, protective clothing, and protective glasses. P332 + P313 – If skin irritation occurs, seek medical care. P305 + P351 + P338 – If in eyes – wash carefully with water for several minutes. Remove eye lenses, if any, and keep on washing. P333 + P 313 – If a skin irritation or a rash occurs – seek medical advice. RECOMMENDATION: Addition of other materials in the ready mixture is not allowed. The recommended temperature range of use is from +5°C to + 35°C. CONSUMPTION RATE: For adhesion: from 4,0 kg/m2 to 5,5 kg/m2 depending on the size of the notches of the square trowel and how even the surface is. For plastering: from 4,0 kg/m2 to 5,0 kg/m2 STORAGE: To be kept in a dry and well ventilated place.
© Copyright 2024