CK739300TX
CONSOLE TABLE-BARNES
Assembly Instructions
Page 1
For assistance with assembly contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[email protected]
www.seidal.com
CK739300TX CONSOLE TABLE-BARNES
Parts List
Please review all parts and hardware before disposing of any packaging. Call Customer Service if missing
hardware. Do not return to store/retailer. Screws shown in actual size. Using a screw that is too long will
cause damage. Before beginning assembly, separate each type of screw. Carefully study the screw
diagrams below (SHOWN ACTUAL SIZE). You may receive extra hardware with your unit.
A.
Quantity
of 1
Quantity
of 1
Middle right divider panel
G.
Quantity
of 2
Metal leg
J.
E.
Quantity
of 1
Middle left divider panel
H.
Quantity
of 1
Quantity
of 3
right Drawer side panel
K.
Quantity
of 1
Drawer back panel
Quantity
of 1
F.
Quantity
of 1
Back panel
I.
Quantity
of 1
Mid-Drawer front panel
Quantity
of 1
Left -Drawer front panel
N.
C.
Right side panel
Cross bar
Right-Drawer front panel
M.
Quantity
of 1
Left side panel
Top panel
D.
B.
Quantity
of 3
L.
Quantity
of 3
left Drawer side panel
O.
Drawer bottom panel
Quantity
of 3
Quantity
of 6
1.
ball bearing slide
Bolt Dia1/4”x9/16”
Quantity
of 32
4.
Cam locks
Screw
Dia3/16”x1/2”L
10.
Quantity
of 8
Flat Washer
13.
leveler
Quantity
of 18
5.
Quantity
of 8
6.
Bolt Dia1/4”x1-13/16”
Quantity
of 12
8.
screw Dia 3/16”x1-1/4”L
Quantity
of 8
11.
Spring Washer
Quantity
of 4
Quantity
of 32
3.
Cam bolt
Wood Dowel
Quantity
of 36
7.
Quantity
of 4
2.
Quantity
of 1
9.
Allen wrench
12.
Screw
Quantity
of 3
Dia 3/16”x1-3/16”L
Quantity
of 12
14.
Plastic cover
For replacement parts or questions, please
Call Customer Service at 1-800-633-5096
Do not return product to store, please call
Manufacturer for assistance, questions or
Parts.
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish . Avoid rubbing or scratching the
surface with rough or abrasive objects.
Assembly Tool Required No.2 Phi
Assembly Tool Required No.2 Phillips
Screwdriver (Not included)
Page 3
CK739300TX CONSOLE TABLE-BARNES
Assembly Instructions
Assembly Instructions:
Assembly the ball bearing slide (7)
on left side panel (B) and right side
panel (C) and middle right divider panel
(D) and middle left divider panel
(E) with screw (5), tighten by
screwdriver(not included)
7 7
1
1
7
1
( 1)
7
1
Figure 1
( 2)
"Please do not over tighten cambolts. Please stop
when you feel tight"
3
5
4
F
Insert Cam bolt (3) into predrilled
holes on back panel(F) and insert
Cam lock (4) into predrilled holes on
middle left divider panel(D),
Then Attach back panel(B) to the
middle left divider panel(D) by
slipping wood dowel(5)& cam bolt(3)
into corresponding predrilled holes on
middle left divider panel(D), secure
by rotating cam locks (4)
counterclockwise with Philips
screwdriver(not included).
Repeat above process for middle
right divider panel(E)
3
H
Figure 2
Page 4
Insert Cam bolt (3) into predrilled
holes on right side panel(C) and
insert Cam lock (4) into predrilled
holes on back panel(F),
Then Attach right side panel(C) to the
back panel(F) by slipping wood
dowel(5)& cam bolt(4) into
corresponding predrilled holes on
back panel(F), secure by rotating
cam locks (4) counterclockwise with
Philips screwdriver(not included).
Attached metal cross bar(H) to right
side panel(C) with hex-head bolt(2),
tighten by Allen wrench(9)
Repeat above process for left side
panel(B)
Figure 3
Insert Cam bolt (3) into predrilled
holes on top panel(A) and insert
Camlock (4) into predrilled holes on
Left side panel(B)&Right side
panel(C)& middle right divider
panel(D)& middle left divider
panel(E)& back panel(F),
Then Attach top panel(A) to figure 3
unit by slipping wood dowel(5)& cam
bolt(3) into corresponding predrilled
holes on figure 3 unit, secure by
rotating cam lock (4)
counterclockwise with Philips
screwdriver(not included).
Figure 4
Page 5
Attach metal leg(G) to Left side
panel(B)&Right side panel(C) by
using hex-head bolt(6) and spring
washer (11) and flat washer(10),
tighten bolt by Allen wrench(9)
Then attach leveler (13) to bottom of
metal leg(E) by hand.
11
10
12
Attached metal cross bar(H) to top
panel(A) with Screw (12), tighten by
screwdriver(not included)
Figure 5
Attach right drawer side panel (M) and
left drawer side panel (L) to drawer back
panel(N) with screw (8), tighten
screw(8) by Philips screwdriver(not
included)
Figure 6
Slide drawer bottom panel (O) into the
groove of right drawer side panel (M)
and left drawer side panel (L) and
drawer back panel(N).
Figure 7
Page 6
Insert Cam bolt (3) into predrilled
holes on middle drawer front panel(I)
and insert Camlock (4) into predrilled
holes on right drawer side panel (M)
and left drawer side panel (L),
counterclockwise with Philips
screwdriver(not included).
Attached Plastic cover ( 14 ) to cam
locks on drawer side panel as
shown.
Figure 8
Insert Cam bolt (3) into predrilled
holes on left drawer front panel(K)
and insert Camlock (4) into predrilled
holes on right drawer side panel (M)
and left drawer side panel (L),
counterclockwise with Philips
screwdriver(not included).
Attached Plastic cover ( 14 ) to cam
locks drawer side panel as shown.
Figure 9
Insert Cam bolt (3) into predrilled
holes on right drawer front panel(J)
and insert Cam lock (4) into
predrilled holes on right drawer side
panel (M) and left drawer side panel (L),
counterclockwise
with
Philips
screwdriver(not included).
Attached Plastic cover ( 14 ) to cam
locks drawer side panel as shown.
Figure 10
Page 7
Assembly the ball bearing slide (1) on
left drawer side panel (L) and right
drawer side panel (M) with screw (7),
tighten by screwdriver(not included)
Figure 11
Assembly the ball bearing slide (1)
on left drawer side panel (L) and right
drawer side panel (M) with screw (7),
tighten by screwdriver(not included)
.
Figure 12
Then your console table is ready to use.
Caution:
Top supports up to 50 lb.
Drawer supports up to 10 lb.
Figure 13
Page 8
Parts Replacement Form
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No
Parts Letter
Parts Description
Quantity Needed
Please immediately examine this product carefully. Any request for missing parts or damage replacement must be
received within 90 days of your receipt of the product. Replacement, if available, will be honored within this time
frame. Parts will not be available for items arriving fully assembled. We do not recommend modifying product(s)
and we are not responsible for any damages due to product modification(s). If damages or missing parts are not
reported within 90 days of your receipt, we are under no obligation to provide parts or replacement merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri Central time
if you have product issues or email us at [email protected]. Please ask for customer service representative for
issues involving damages or replacement parts. Please ask for technical assistance representative for any issues
with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Service 1-800-633-5096
[email protected]
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019