1. No category

Sensing and Control
SMD Receiver Component
OPL6000
Features:
•
•
•
•
•
•
Up to 256kbps OperaƟon
Up to 250klux Ambient Light Immunity
Output Drive for Interfacing to Microcontroller
Reverse Gull Wing Design
Compliant with Smart Power Meter Standard ANSI C12.18
CompaƟble with OP181 EmiƩer Component
DescripƟon:
The OPL6000 is a surface mount receiver component incorporaƟng a custom CMOS ASIC. The product features a digital
output in a push-pull inverter design. The circuitry provides ambient light immunity while maintaining low power
consumpƟon. The ASIC is lead frame mounted and overmolded, incorporaƟng a lens to achieve maximum light coupling
ability. In addiƟon, the overmold compound provides visible light rejecƟon. While this part has been designed specifically
for the smart power meter industry, other applicaƟons are certainly possible.
ApplicaƟons:
•
•
Smart power meter opƟcal port
Over the air communicaƟons
Note: The VDD and N/C leads are
the wider of the four leads
as indicated above but also
have red strip indicator on
the boƩom of the leads.
Dimensions are ±0.005 unless otherwise specified
General Note
TT Electronics reserves the right to make changes in product specificaƟon
without noƟce or liability. All informaƟon is subject to TT Electronics’ own data
and is considered accurate at Ɵme of going to print.
© TT electronics plc
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
www.optekinc.com | www.Ʃelectronics.com
Issue B
01/2015
Page 1
Sensing and Control
SMD Receiver Component
OPL6000
Absolute Maximum RaƟngs (TA = 25° C unless otherwise noted)
Overall Product
-55o C to +100o C
Storage Temperature Range
-40o C to +85o C
OperaƟng Temperature Range
D.C. Supply Voltage
3.0 - 5.5 V
Output Drive Current
1 mA
Power DissipaƟon in AcƟve / InacƟve Mode
(1)(2)
30 mW / 5mW(2)
Incident Irradiance
Solder Reflow Temperature
250,000 lux
(3)
260° C
Notes:
1. AcƟve mode is defined as the state during which Ɵme a signal is being received and the output stages are acƟve.
InacƟve mode is defined as the state during which Ɵme no signal is being received and the output stages are inacƟve.
2. Derate linearly at 0.40 mW/°C (acƟve mode) and 0.067 mW/°C (inacƟve mode) above 25°C.Solder Ɵme less than 5 seconds at temperature
extreme.
3. Solder Ɵme less than 5 seconds at temperature extreme. Solder Ɵme within 5° of peak temperature is 20 to 40 seconds.
Recommended PCB Layout
General Note
TT Electronics reserves the right to make changes in product specificaƟon
without noƟce or liability. All informaƟon is subject to TT Electronics’ own data
and is considered accurate at Ɵme of going to print.
© TT electronics plc
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
www.optekinc.com | www.Ʃelectronics.com
Issue B
01/2015
Page 2
Sensing and Control
SMD Receiver Component
OPL6000
Electrical SpecificaƟons
Electrical CharacterisƟcs (TA = 25 °C unless otherwise noted)
SYMBOL
VDD
IDD
PARAMETER
MIN
TYP
MAX
UNITS
3.0
3.3
5.5
V
AcƟve
Mode
-
-
5
InacƟve
Mode
-
-
1.0
10
-
-
%
OperaƟng Supply
Voltage
Supply Current(1)
mA
TEST CONDITIONS
VDD = 3.0 to 5.5 V
No load current
PSRR
Power Supply RejecƟon RaƟo
EeT(+)
PosiƟve Going
Threshold Irradiance
-
0.100
0.125
mW/cm2
VOL
Low Level Output Voltage
-
300
400
mV
VDD = 3.0 to 5.5 V, IO = 1 mA
Ee = 0 mW/cm2
VOH
High Level Output Voltage
VDD - 1.0
-
-
V
VDD = 3.0 to 5.5 V, IO = 1 mA
Ee = 7.5 mW/cm2
tr, tf
Rise Time, Fall Time
-
-
150
ns
-
-
1.0
µs
tPDLH, tPDHL PropagaƟon Delay
II
Input Leakage Current
-10
-
10
µA
IO
Output Drive Current
-
-
1.0
mA
f = 1 - 1 MHz, VDD > 3.0V
VDD = 3.3 V
lp = 940 nm; collimated radiaƟon
VDD = 3.3 V, f = 1 kHz
Ee = 7.5 mW/cm2
Decouple Cap (VDD to GND) = 0.1 µF
VDD = 3.3 V
Notes:
1. AcƟve mode is defined as the state during which Ɵme a signal is being received and the output stages are acƟve.
InacƟve mode is defined as the state during which Ɵme no signal is being received and the output stages are inacƟve.
General Note
TT Electronics reserves the right to make changes in product specificaƟon
without noƟce or liability. All informaƟon is subject to TT Electronics’ own data
and is considered accurate at Ɵme of going to print.
© TT electronics plc
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
www.optekinc.com | www.Ʃelectronics.com
Issue B
01/2015
Page 3
Sensing and Control
SMD Receiver Component
OPL6000
Supply Current
General Note
TT Electronics reserves the right to make changes in product specificaƟon
without noƟce or liability. All informaƟon is subject to TT Electronics’ own data
and is considered accurate at Ɵme of going to print.
© TT electronics plc
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
www.optekinc.com | www.Ʃelectronics.com
Issue B
01/2015
Page 4
Sensing and Control
SMD Receiver Component
OPL6000
Rise/Fall Time
General Note
TT Electronics reserves the right to make changes in product specificaƟon
without noƟce or liability. All informaƟon is subject to TT Electronics’ own data
and is considered accurate at Ɵme of going to print.
© TT electronics plc
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
www.optekinc.com | www.Ʃelectronics.com
Issue B
01/2015
Page 5
Sensing and Control
SMD Receiver Component
OPL6000
PropagaƟon Delay
General Note
TT Electronics reserves the right to make changes in product specificaƟon
without noƟce or liability. All informaƟon is subject to TT Electronics’ own data
and is considered accurate at Ɵme of going to print.
© TT electronics plc
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
www.optekinc.com | www.Ʃelectronics.com
Issue B
01/2015
Page 6
Sensing and Control
SMD Receiver Component
OPL6000
Pulse Width DistorƟon
General Note
TT Electronics reserves the right to make changes in product specificaƟon
without noƟce or liability. All informaƟon is subject to TT Electronics’ own data
and is considered accurate at Ɵme of going to print.
© TT electronics plc
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
www.optekinc.com | www.Ʃelectronics.com
Issue B
01/2015
Page 7
Sensing and Control
SMD Receiver Component
OPL6000
High and Low Level Output Voltage
General Note
TT Electronics reserves the right to make changes in product specificaƟon
without noƟce or liability. All informaƟon is subject to TT Electronics’ own data
and is considered accurate at Ɵme of going to print.
© TT electronics plc
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
www.optekinc.com | www.Ʃelectronics.com
Issue B
01/2015
Page 8
Sensing and Control
SMD Receiver Component
OPL6000
SensiƟvity
General Note
TT Electronics reserves the right to make changes in product specificaƟon
without noƟce or liability. All informaƟon is subject to TT Electronics’ own data
and is considered accurate at Ɵme of going to print.
© TT electronics plc
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
www.optekinc.com | www.Ʃelectronics.com
Issue B
01/2015
Page 9
Sensing and Control
SMD Receiver Component
OPL6000
Frequency Response
General Note
TT Electronics reserves the right to make changes in product specificaƟon
without noƟce or liability. All informaƟon is subject to TT Electronics’ own data
and is considered accurate at Ɵme of going to print.
© TT electronics plc
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
www.optekinc.com | www.Ʃelectronics.com
Issue B
01/2015
Page 10
Sensing and Control
SMD Receiver Component
OPL6000
Packaging
Notes:
1. Dimensions are in mm.
2. VDD and N/C lead (marked
with red stripe) is nearest
sprocket holes.
General Note
TT Electronics reserves the right to make changes in product specificaƟon
without noƟce or liability. All informaƟon is subject to TT Electronics’ own data
and is considered accurate at Ɵme of going to print.
© TT electronics plc
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
www.optekinc.com | www.Ʃelectronics.com
Issue B
01/2015
Page 11