1. health and fitness
2. alternative medicine

room essentials
4 drawer chest
DPCI # 249 - 05 - 0103 (Black Woodgrain)
DPCI # 249 - 05 - 0106 (Espresso)
>> assembly instructions
92335 E
1
FREE!
Do not go back to your store!
we will help you!
Missing or Damage Parts? Have Questions about Assembly?
The store where you made this purchase does not stock parts for this item.
If you needs parts (damaged or missing) or have questions about assembly,
please call our toll free support line. All orders normally ship within 24 hours.
Just call 1-855-MYTGTHOME (855-698-4846) for parts and service.
For faster service, have the style number and DPCI number ready
when calling.
2
Congratulations on your latest Target purchase
Don't start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you'll be on your way to transforming your
room in no time. Good luck - though we're confident you won't need it.
before you begin
1.
Check for damaged or missing parts. Please call 1-855-MYTGTHOME (855-698-4846) for parts and service. Please reference DPCI#
249 - 05 - 0103 (Black Woodgrain)
249 - 05 - 0106 (Espresso)
2.
3.
4.
Use the carton as a worksurface to prevent product damage during assembly.
Gather all tools prior to assembly.
Two people are required for assembly.
tools needed
3
table of contents
customer service information
2
introduction
3
parts list
5
hardware
how to use the cam lock system
assembly
QUESTIONS?
6-7
8
9 - 29
specification sheet
30
information sheet
31
products available
32
Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI# number ready when calling.
4
ITEM
DESCRIPTION
QUANTITY
00470
right drawer side
4
00471
left drawer side
4
03077
drawer back
4
07531
drawer bottom
4
08849
back panel
1
EA
drawer front
4
ID
bottom panel
1
LA
top panel
1
PA
top rail
1
PB
rail
4
FC
left end panel
1
HC
right end panel
1
08849
LA
PA
FC
PB
PB
00471
HC
03077
PB
07531
ID
EA
00470
PB
5
hardware
10401
12754
13414
20209
20228
x26
x4
x2
x26
x16
panel clips
rectangular foot
corner bracket
drawer fastener
dowel pin
21812
25233
25241
25266
x24
x4
x8
x2
spacer
short flat head screw
flat head screw
long flat head screw
26027
26214
31685
31686
x24
x8
x8
x8
1/4" screw
machine screw
small cam
large cam
6
hardware
31570
41407
x16
x8
88060
x1
94009
x2
cam bolt
wall attachment strip
drawer tip warning label
drawer glide
7
how to use the cam lock system
1
3
2
CORRECT
NOT
CORRECT
180°
4
5
6
8
step 1 drawer assembly - attach drawer bottom to back
03077
07531
x4
paper
1.
Press the drawer bottom (with the finished side up) into the grooves on the drawer back.
2.
Paper overlays the slot, but it has a slit so drawer bottom inserts well.
9
step 2 drawer assembly - attach drawersides
00470
07531
20228
00471
x4
x16
drawer fastener
1.
Press the grooves on the drawer sides onto the drawer bottom (with the finished side up).
2.
Use a small hammer to nail the drawer sides to the drawers back (use drawer 4x fastener for each drawer).
10
step 3 drawer assembly - insert cam bolts
EA
x4
31570
x8
drawer front
cam bolt
1.
Screw cam bolts into the drawer front. Cam bolts must be screwed down flush.
11
step 4 drawer assembly - attach drawer front and insert drawer cams
88060
00470
NOT
CORRECT
CORRECT
03077
07531
31685
88060
x8
x1
finish side up
EA
small cam
00471
1.
Place cams in large holes so that the arrow on cam faces the edge of the panel.
2.
Place the cam bolts that are attached to the drawer front into the holes on the drawer sides.
3.
Make sure the drawer bottom is completely inserted into the grooves and tighten the cams. (look at page 8 for help if needed).
4.
Apply drawer tip warning label to the inside of the top drawer.
x4
12
step 5 drawer assembly - attach panel clips
00470
10"
EA
07531
10 "
03077
10401
x16
x4
00471
panel clips
1.
Place back panel clips as shown and press the thin tabs between the back panel and the groove.
2.
Tighten the screws but be careful not to over tighten.
13
step 6 case assembly - insert dowel pins
PA
PB
20209
x4
x18
dowel pin
1. Press dowel pins into the holes at the end of the 4 rails (PB) and on the top side of the rail (PA) as shown on the picture.
14
step 7 case assembly - insert dowel pins, cams and corner bracket
ID
PB
13414
x2
20209
25233
31686
x4
x2
x4
dowel pin
corner bracket
short flat head screw
x1
large cam
1.
Press the dowel pins into the large holes at the end of the top (ID).
2.
Put large cams into the 4 holes on the downside of the top (ID) and make sure the the arrow on the cam is toward the edge.
3.
Screw corner bracket on to one of the rails (PB) as shown on the picture.
15
step 8 case assembly - insert cams and dowel pins
CORRECT
NOT
CORRECT
FC
20209
31686
31570
x2
x2
x2
dowel pin
large cam
cam bolt
1.
Tap the dowel pins into the larger holes at the top edge of the left end panel.
2.
Place the large cam into the holes on the left end panel.
3.
Screw the cam bolts into the small holes (inner holes)at the bottom of the left end panel. Cam bolts must be screwed down flush.
16
step 9 case assembly - attach drawer glides.
front of glide
back screw location
front screw location
to
h
p/
au
t
back
FC
front (finished edge)
21812
26027
41407
x12
x12
x4
bottom
spacer
1/4" screw
drawer glide
1.
Fully extend drawer glides to the front.
2.
Place 1/4" screws through the correct holes for the back and middle screws of the drawer slide,
then through the spacers and into the holes on the panel.
3.
Tighten screws but do not over tighten.
4.
Close slide until the front hole is visible through the oval slot on the glide.
5.
Place 1/4" screws through the hole in the slot and through the spacer.
6.
Tighten screw but do not over tighten.
17
step 10 case assembly - insert cams and dowel pins
CORRECT
NOT
CORRECT
HC
20209
31686
31570
x2
x2
x2
dowel pin
large cam
cam bolt
1.
Tap the dowel pins into the larger holes at the top and bottom edges of the right end panel
2.
Place the large cam into the holes on the right end panel.
3.
Screw the cam bolts into the small holes (inner holes) at the bottom of the left end panel. Cam bolts must be screwed down flush.
18
step 11 case assembly - attach drawer glides
front of glide
back screw location
front screw location
top
front (finished edge)
HC
21812
26027
41407
x12
x12
x4
back
bottom
spacer
1/4" screw
drawer glide
1.
Fully extend drawer glides to the front.
2.
Place 1/4" screws through the correct holes for the back and middle screws of the drawer slide,
then through the spacers and into the holes on the panel.
3.
Tighten screws but do not over tighten.
4.
Close slide until the front hole is visible through the oval slot on the glide.
5.
Place 1/4" screws through the hole in the slot and through the spacer.
6.
Tighten screw but do not over tighten.
19
step 12 case assembly - attach top rail
PA
LA
f in is
31570
25266
x4
x2
hed
f
ront
edg
e
finished
front edge
long flat head screw
cam bolt
1.
Screw the cam bolts into the small holes (inner holes) on top panel. Cam bolts must be screwed down flush.
2.
Place long flat head screws through holes on top rail. Make sure the finished side of the rail is facing the front.
3.
Line up dowel pins with the holes in the top panel, then tighten screws.
20
step 13 base assembly - attach rail and bottom pannel
PB
ID
FC
1.
Put dowels on the rail (with corner brackets) into the holes on the left panel (in the middle of the side).
2.
Place the bottom panel to the left panel inserting dowel pins and cam bolts into the holes.
21
step 14 base assembly - attach rail and panel
HC
ID
PB
1.
Attach the remaining rails (PB) and the right panel (HC).
2.
Make sure dowel pins and cam bolts are completely inserted and then tighten the cams under the bottom.
22
step 15 case assembly - attach back panel
HC
08849
08849
PB
PB
PB
ID
FC
PB
1.
Attach the back panel by sliding it into the grooves in the side and bottom panels.
23
step 16 case assembly - attach top assembly
HC
LA
PB
PB
PB
ID
FC
PB
1.
Attach the top panel by pressing in onto the back panel and by inserting dowel pins and cam bolts into the holes.
2.
Make sure dowel pins and cam bolts are completely inserted and then tighten the cams.
24
step 17 case assembly - attach corner bracket
HC
LA
25233
x2
08849
ID
short flat head screw
FC
1.
Fasten the middle rail (with corner brackets) to the left and right panel with the short flat headed screws.
25
1/4"
step 18 case assembly - attach rectangular feet
IMPORTANT:
When placing this unit on thick carpet,
the addition of 4 rectangular feet is
required to improve stability.
For floors with a hard surface or low
pile carpeting, the additional feet are
not necessary.
finished
front edge
front
edge
LA
FC
08849
25241
x4
x8
HC
1"
12754
back
edge
ID
flat head screw
rectangular foot
1.
Place a rectangular foot on the bottom of the side panel at a distance from the front edge of 1/4" and 1" from the back edge, centered on the width of the panel-side.
2.
Place the screws through to two holes and gently screw them onto the side panel. Make sure to fasten the screws, but be careful not to over tighten.
3.
Repeat step 1-2 for the remaining 2 feet.
26
step 19 case assembly - attach back panel clips
2"
4"
90°
ID
HC
90°
4"
08849
10401
x10
FC
panel clips
1.
Place back panel clips as shown and press the thin tabs between the back panel and the groove.
2.
Tighten the screws but be careful not to over tighten.
LA
27
step 20 case assembly - mount wall attachment strips
2
1
3
1 1/5"
LA
94009
x2
IMPORTANT.
The screw supplied together with the wall attachment strip
is to be used only for fixing the wall attachment strip to the
furniture.
In addition to this, you will need to choose a screw or
fitting which is suitable for securing the bracket to the
kind of walls you have. If you are unsure about what type
of screw to use contact your local hardware store.
Wall attachment strips are requred to be installed.
FC
08849
HC
ID
wall attachment strip
28
step 21 case assembly - install drawers into case
LA
EA
EA
HC
26214
EA
x8
EA
machine screw
1.
Slide groove on drawer sides over the drawer glide.
2.
Pull the slide forward until the threaded hole on the glide aligns with the hole in the drawer side.
3.
Attach glide screw from inside the drawer box into the drawer glide.
29
specification sheet
3 YEAR WARRANTY:
All Tvilum furniture is warranted to the original
purchaser at the time of purchase and for 3
years after the purchase date. We warrant to
you, the original purchaser, that our furniture
and all furniture parts and components are free
of defects in material or workmanship. The
word “defects” as used in this warranty is
defined as any imperfections which impair the
use of the furniture.
Our warranty is expressly limited to the replacement or repair of furniture parts and
components and Tvilum will have a reasonable
amount of time to remedy said defect. This
warranty applies under conditions of normal
use. The warranty does not cover defects
caused by improper assembly or disassembly
defects occurring after purchase due to
intentional damage, product modifications,
exposure to the elements, accidents, misuse,
abuse or negligence and labor or assembly
costs.
30 kg
60 lbs
9 kg
20 lbs
All implied warranties, including the warranty of
merchantability shall not extend beyond the
duration of the written warranty stated above.
Tvilum liability is expressly limited to the costs
of material for repair or replacement of
defective goods and in no event will Tvilum be
liable for incidental or consequential damages
resulting from use of the product. Some states
do not allow limitations on how long an implied
warranty may last or the exclusions or
limitations of incidental or consequential
damages, so the above limitations and
exclusions may not apply to you.
This warranty gives you specific legal rights
which may vary from state to state.
Any claims made under this warranty must be
presented in writing to:
Tvilum
2195 Philpott Road
South Boston, VA 24592
30
A
Read more at www.tvilum.com
THIS�PRODUCT
will ensure you
A product tested for harmful substances
Helps to maintain healthy indoor climate
Wood from sustainable forestry
The furniture is PEFC-certified
Safe furniture for use in your home
The furniture has been safety tested and approved
Minimum 25% post consumer recycled materials
NOUS�VOUS�GA
que ce produit:
A été évalué pour toute substance da
pour garder un environnement sain à
de votre maison
Est fabriqué à partir de foresterie du
Ce mobilier est certifié PEFC
Est sûr pour votre intérieur
le produit a passé les contrôles de séc
et a été approuvé
Contient un minimum de 25 % de
matériel recyclé postconsommation.
31
products available
6 drawer dresser
4 drawer dresser
32
33