Download Report

room essentials
6 drawer dresser
DPCI # 249 - 05 - 0102 (Black Woodgrain)
DPCI # 249 - 05 - 0105 (Espresso)
>> assembly instructions
92336 D
1
FREE!
Do not go back to your store!
we will help you!
Missing or Damage Parts? Have Questions about Assembly?
The store where you made this purchase does not stock parts for this item.
If you needs parts (damaged or missing) or have questions about assembly,
please call our toll free support line. All orders normally ship within 24 hours.
Just call 1-855-MYTGTHOME (855-698-4846) for parts and service.
For faster service, have the style number and DPCI number ready
when calling.
2
Congratulations on your latest Target purchase
Don't start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you'll be on your way to transforming your
room in no time. Good luck - though we're confident you won't need it.
before you begin
1.
Check for damaged or missing parts. Please call 1-855-MYTGTHOME (855-698-4846) for parts and service. Please reference DPCI#
249 - 05 - 0102 (Black Woodgrain)
249 - 05 - 0105 (Espresso)
2.
3.
4.
Use the carton as a worksurface to prevent product damage during assembly.
Gather all tools prior to assembly.
Two people are required for assembly.
tools needed
3
table of contents
customer service information
2
introduction
3
parts list
5
hardware
how to use the cam lock system
assembly
QUESTIONS?
6-7
8
9 - 31
specification sheet
32
information sheet
33
products available
34
Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.
4
ITEM
DESCRIPTION
QUANTITY
00470
right drawer side
6
00471
left drawer side
6
03077
drawer back
6
07531
drawer bottom
6
08848
back panel
2
EA
drawer front
6
IE
bottom panel
1
JD
base rail
1
LB
top panel
1
PC
top rail
2
PD
rail
4
FD
left end panel
1
HD
right end panel
1
divider panel
1
G
08848
08848
LB
PC
FD
PD
PC
G
PD
00471
HD
03077
IE
07531
JD
EA
00470
5
hardware
10401
12754
13414
20209
20228
21812
x40
x5
x6
x36
x24
x18
panel clips
Rectangular foot
corner bracket
dowel pin
drawer fastener
spacer
25233
25241
25266
25610
26020
26027
x12
x10
x4
x2
x18
x18
long flat head screw
connector bolt
short 1/4" screw
short flat head screw
flat head screw
26214
31685
31686
x12
x12
x10
machine screw
small cam
large cam
long 1/4" screw
6
hardware
31570
41407
88060
94009
97642
x22
x12
x1
x2
x1
cam bolt
allen wrench
wall attachment strip
Drawer Tip Warning Label
drawer glide
7
how to use the cam lock system
1
3
2
CORRECT
NOT
CORRECT
180°
4
5
6
8
step 1 drawer assembly - attach drawer bottom to back
03077
finish side up
07531
x6
paper
1.
Press the drawer bottom (with the finished side up) into the grooves on the drawer back.
2.
Paper overlays the slot, but it has a slit so drawer bottom inserts well.
9
step 2 drawer assembly - attach drawer side
00470
03077
07531
20228
x6
x24
00471
drawer fastener
1.
Align holes at back of the drawer sides, with the holes on the drawer back.
2.
Tap drawer fasteners into place with a hammer.
10
step 3 drawer assembly - insert cam bolts
EA
31570
x12
x6
cam bolt
1.
Screw cam bolts into the drawer front. Cam bolts must be screwed down flush.
11
step 4 drawer assembly - attach drawer front and insert drawer cams
88060
00470
NOT
CORRECT
CORRECT
finish side up
03077
31685
88060
x12
x1
07531
00471
small cam
EA
x6
Drawer Tip Warning Label
1.
Place cams in large holes so that the arrow on cam faces the edge of the drawer sides.
2.
Make sure the drawer bottom is completely inserted into the grooves in the drawer front and drawer back, then tighten the cams.
3.
Apply drawer tip warning label to the inside of the top drawer
12
step 5 drawer assembly - attach panel clips
00470
EA
10"
07531
10"
03077
10401
x24
00471
panel clips
1.
Place back panel clips as shown and press the thin tabs between the back panel and the groove.
2.
Tighten the screws but be careful not to over tighten.
x6
13
step 6 case assembly - insert dowel pins
PC
x2
PD
20209
x20
x4
dowel pin
1.
Press dowel pins into the holes at the end of the 4 rails (PD) and on the top side of the 2 rails (PC) as shown on the picture.
14
step 7 case assembly - insert dowel pins and cams
CORRECT
NOT
CORRECT
IE
JD
13414
20209
25233
31686
x6
x8
x6
x4
corner bracket
PD x2
large cam
dowel pin
short flat
head screw
1.
Tap the dowel pins into the larger holes at the ends of edges of the bottom panel and base rail.
2.
Place the large cam into the holes on the bottom panel.
3.
Make sure the arrow on the cam is toward the edge of the panel.
4.
Use the short flat head screws to attach the long side of the corner brackets to the base rail (JD) and 2 rails (PD) as shown on the picture.
15
step 8 case assembly - insert cams and dowel pins
CORRECT
NOT
CORRECT
FD
20209
x2
31570
31686
x2
x2
large cam
dowel pin
cam bolt
1.
Tap the dowel pins into the larger holes at the top and bottom edges of the left end panel.
2.
Place the large cam into the holes on the left end panel.
3.
Make sure the arrow on the cam is toward the edge of the panel.
4.
Screw the cam bolts into the left panel. Cam bolts must be screwd down flush.
16
step 9 case assembly - attach drawer glides.
front of glide
back screw location
front screw location
top
FD
21812
26027
41407
x9
x9
x3
back
front (finished edge)
bottom
spacer
1/4" screw
drawer glide
1.
Fully extend drawer glides to the front.
2.
Place 1/4" screws through the correct holes for the back and middle screws of the drawer slide,
then through the spacers and into the holes on the panel.
3.
Tighten screws but do not over tighten.
4.
Close slide until the front hole is visible through the oval slot on the glide.
5.
Place 1/4" screws through the hole in the slot and through the spacer.
6.
Tighten screw but do not over tighten.
17
step 10 case assembly - insert cams and dowel pins
CORRECT
NOT
CORRECT
HD
20209
x2
dowel pin
31570
31686
x2
x2
cam bolt
large cam
1.
Tap the dowel pins into the larger holes at the top and bottom edges of the right end panel.
2.
Place the large cam into the holes on the right end panel.
3.
Make sure the arrow on the cam is toward the edge of the panel.
4.
Screw the cam bolts into the right panel. Cam bolts must be screwd down flush.
18
step 11 case assembly - attach drawer glides
front of glide
back screw location
front screw location
front (finished edge)
top
HD
21812
26027
41407
x9
x9
x3
back
bottom
spacer
1/4" screw
drawer glide
1.
Fully extend drawer glides to the front.
2.
Place 1/4" screws through the correct holes for the back and middle screws of the drawer slide,
then through the spacers and into the holes on the panel.
3.
Tighten screws but do not over tighten.
4.
Close slide until the front hole is visible through the oval slot on the glide.
5.
Place 1/4" screws through the hole in the slot and through the spacer.
6.
Tighten screw but do not over tighten.
19
step 12 case assembly - insert cams and dowel pins
CORRECT
NOT
CORRECT
G
20209
31686
x4
x2
dowel pin
large cam
1.
Tap the dowel pins into the larger holes at the top and bottom edges of the divider panel.
2.
Place the large cam into the holes on the divider panel.
3.
Make sure the arrow on the cam is toward the edge of the panel.
20
step 13 case assembly - divider panel
front of glide
back screw location
front screw location
top
back
front (finished edge)
26020
41407
x18
x6
G
bottom
short 1/4"
screw
drawer glide
1.
Fully extend drawer glides to the front of the divider panel.
2.
Place 1/4" screws through the correct holes for the back and middle screws of the drawer slide.
3.
Tighten screws but do not over tighten.
4.
Close slide until the front hole is visible through the oval slot on the glide.
5.
Tighten screw but do not over tighten.
21
step 14 case assembly - attach top rail
PC
LB
finished
front edge
PC
f in is
31570
25266
x6
x4
cam bolt
hed
f
ront
edg
e
long flat head screw
1.
Screw the cam bolts into the top panel. Cam bolts must be screwed down flush.
2.
Place long flat head screws through holes on top rail. Make sure the finished side of the rail is facing the front.
3.
Line up dowel pins with the holes in the top panel, then tighten screws.
22
step 15 case assembly - attach divider panel to bottom panel
finished front edge
G
25610
97642
x2
x1
IE
connector bolt
allen wrench
1.
Place the divider panel end over the bottom pannel.
2.
Use the allen wrech to install connector bolts.
23
step 16 case assembly - attach rail and panel
finished
front edge
FD
PD
PD
G
IE
1.
Two people are needed for this assembly step.
2.
Place the cam bolts from the left panel into the holes on the bottom panel and tighten the cams.
3.
Place the ends of the two rails into the holes and hold in place.
24
step 17 case assembly - attach rail and panel
FD
PD
PD
G
PD
PD
JD
IE
HD
1.
Two people are needed for this assembly step.
2.
Place the cam bolts from the right panel into the holes on the bottom panel and tighten the cams.
3.
Place the ends of the two rails and base rail into the holes and hold in place.
25
step 18 case assembly - attach back panel and top panel
LB
FD
08848
08848
08848
G
HD
1.
Attach the back panel by sliding it into the grooves in the side and bottom panel.
2.
Attach the top panel by pressing in onto the back panel and by inserting dowel pins and cam bolts into the holes.
3.
Make sure dowel pins and cam bolts are completely inserted and then tighten the cams.
26
step 19 case assembly - attach rectangular feet
12754
25241
x5
x10
rectangular foot
flat head screw
1/4"
1"
back
edge
IMPORTANT:
When placing this unit on thick carpet,
the addition of 5 rectangular feet is
required to improve stability.
For floors with a hard surface or low
pile carpeting, the additional feet are
not necessary.
front
edge
1.
Place a rectangular foot on the bottom of the side panel at a distance from the front edge of 1/4" and 1" from the back edge, centered on the width of the panel-side.
2.
Place the screws through to two holes and gently screw them onto the side panel. Make sure to fasten the screws, but be careful not to over tighten.
3.
Repeat step 1-2 for the remaining 2 feet.
27
step 20 case assembly - attach back panel clips and brackets
3"
4"
90°
4"
90°
HD
10401
25233
x16
x2
panel clips
08848
08848
short flat head screw
IE
FD
1.
Place back panel clips as shown and press the thin tabs between the back panel and the groove.
2.
Tighten the screws but be careful not to over tighten.
3.
Add screws into bracket.
JD
28
step 21 case assembly - attach corner bracket
LB
08848
FD
G
08848
25233
IE
HD
x4
short flat head screw
1.
Fasten the middle rail (with corner brackets) to the panels with the short flat head screw.
29
step 22 case assembly - mount wall attachment strips
2
1
3
1 1/5"
LB
94009
x2
08848
IMPORTANT.
The screw supplied together with the wall attachment
strip is to be used only for fixing the wall attachment
strip to the furniture.
In addition to this, you will need to choose a screw or
fitting which is suitable for securing the bracket to the
kind of walls you have. If you are unsure about what type
of screw to use contact your local hardware store.
Wall attachment strips are requred to be installed.
FD
G
08848
IE
HD
wall attachment strip
30
step 23 case assembly - install drawers into case
LB
EA
EA
EA
26214
EA
EA
HD
x12
EA
machine screw
1.
Slide groove on drawer sides over the drawer glide.
2.
Pull the slide forward until the threaded hole on the glide aligns with the hole in the drawer side.
3.
Attach glide screw from inside the drawer box into the drawer glide.
4.
Second hole on drawer slide is not used.
31
specification sheet
3 YEAR WARRANTY:
All Tvilum furniture is warranted to the original
purchaser at the time of purchase and for 3
years after the purchase date. We warrant to
you, the original purchaser, that our furniture
and all furniture parts and components are free
of defects in material or workmanship. The
word “defects” as used in this warranty is
defined as any imperfections which impair the
use of the furniture.
Our warranty is expressly limited to the replacement or repair of furniture parts and
components and Tvilum will have a reasonable
amount of time to remedy said defect. This
warranty applies under conditions of normal
use. The warranty does not cover defects
caused by improper assembly or disassembly
defects occurring after purchase due to
intentional damage, product modifications,
exposure to the elements, accidents, misuse,
abuse or negligence and labor or assembly
costs.
60 kg
132 lbs
9 kg
20 lbs
All implied warranties, including the warranty of
merchantability shall not extend beyond the
duration of the written warranty stated above.
Tvilum liability is expressly limited to the costs
of material for repair or replacement of
defective goods and in no event will Tvilum be
liable for incidental or consequential damages
resulting from use of the product. Some states
do not allow limitations on how long an implied
warranty may last or the exclusions or
limitations of incidental or consequential
damages, so the above limitations and
exclusions may not apply to you.
This warranty gives you specific legal rights
which may vary from state to state.
Any claims made under this warranty must be
presented in writing to:
Tvilum
2195 Philpott Road
South Boston, VA 24592
32
A
Read more at www.tvilum.com
THIS�PRODUCT
will ensure you
A product tested for harmful substances
Helps to maintain healthy indoor climate
Wood from sustainable forestry
The furniture is PEFC-certiﬁed
Safe furniture for use in your home
The furniture has been safety tested and approved
Minimum 25% post consumer recycled materials
NOUS�VOUS�GA
que ce produit:
A été évalué pour toute substance da
pour garder un environnement sain à
de votre maison
Est fabriqué à partir de foresterie du
Ce mobilier est certiﬁé PEFC
Est sûr pour votre intérieur
le produit a passé les contrôles de séc
et a été approuvé
Contient un minimum de 25 % de
matériel recyclé postconsommation.
33
products available
4 drawer dresser
6 drawer dresser
34
35