1. No category

Ring Sizing Guide
*Sizes & dimensions are approximate.
Make sure your printer is set to 100-percent. Do not reduce the print size in your printer ‘page
setup’ area. You can verify that the ring sizer printed correctly by measuring it with a ruler; it should
measure 3 1/2 inches long from "A" to "B".
To open the print dialog box, press CTRL + P for pc or COMMAND +P for mac.
Ring Sizing Guide
Use a quarter to
make sure this page
is printed at the
correct size.
Method A: Measure Your Finger
*Sizes & dimensions are approximate.
Make
sure
set to 100Dopercent.
Dothenot
reduce
the printer
print size
Make
your
printer
is set to is
100-percent.
not reduce
print
size in your
‘pagein your page setup area (see dialog box below).
1.
Cutsure
out
theyour
ring printer
sizer.
setup’
area.
You canto
verify
thatsure
the ring
sizer
printed
correctly at
by the
measuring
it with
a ruler; it should
Use
a
quarter
make
this
page
is
printed
correct
size.
2.
Cut a3slit
for Slotlong
"A".
measureprinted
1/2 inches
from "A" to
quarter
should
be"B".thewhere
samethe
sizering
as an
quarter
on numbers
top of it. are facing out.
3.The
Wrap the sizer
around
the finger
willactual
be worn.
Makeplaced
sure the
To open the print dialog box, press CTRL + P for pc or COMMAND +P for mac.
4. Pull the pointed end Tab "B" through Slot "A"until the sizer is snug. Make sure to allow size for your knuckle. If your
To open
the print
dialog box,
press CTRL+P for PC or COMMAND+P for Mac.
knuckle
is size
in between
the two.
5. The number aligned with Slot "A" is your ring size.
Use a quarter to
6. If the measurement lands between two numbers, your size is a half size.
make sure this page
Example: IfSample
your measurement
falls between 5 and 6, your ring size is 5 1/2.
is printed at the
Dialog Box
Method A: Measure Your Finger
correct size.
1.
Cut out
the
ring sizer.
Sizing
Tip:
Measure
your finger at the beginning of the day to avoid incorrect measurements. More sizing mistakes are
2.
Cut
a
slit
for
Slotrings
"A". too large rather than too small.
made by ordering
3. Wrap the sizer around the finger where the ring will be worn. Make sure the numbers are facing out.
4. Pull the pointed end Tab "B" through Slot "A"until the sizer is snug. Make sure to allow size for your knuckle. If your
knuckle is size in between the two.
5. The number aligned with Slot "A" is your ring size.
Read
6. If the measurement lands
between two numbers, your size is a half size.
Sizefalls between 5 and 6, your ring size is 5 1/2.
Example: If your measurement
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
A
Here
select
actual size
B
Sizing Tip: Measure your finger at the beginning of the day to avoid incorrect measurements. More sizing mistakes are
made by ordering rings too large rather than too small.
3½ Inches
Read
Size
Here
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
A
Method B: Measure a Ring that Fits
B
1. Select a ring that properly fits the intended finger.
3½the
Inches
2. Place the ring on top of the circle below until the inside edge of
ring matches the outside of the circle.
Comfort Fit Ring Tip: If the ring is a comfort fit design, match circles to the contoured edge of the inner surface of the ring.
Size 4.5
Size 6.5
Size 5.5
Size 6
Size 5
Method
B:
Measure
that Fits
14.8 mm
16.9 mm
16 mm a Ring
16.45 mm
15.6
mm
Size 8
18.2 mm
Size 7.5
17.7 mm
Size 7
17.3 mm
1. Select a ring that properly fits the intended finger.
2. Place the ring on top of the circle below until the inside edge of the ring matches the outside of the circle.
Size 8.5
Size 9
Size 9.5
Size 10
Size 11.5
Size 11
Size 10.5
21 mm
Comfort
If the ring is
a comfort
fit design,
match circles
edge of the inner
surface of the ring.
19 mm
19.4
mm
18.6 mmFit Ring Tip:
20.6 mm
20.2 to
mmthe contoured
19.9 mm
Size 4.5
14.8 mm
Size 12
21.4 mm
Size 8.5
18.6 mm
Size 5.5
Size 5
16 mm
15.6 mm
Size 12.5
21.8 mm
Size 9
19 mm
Size 6
16.45 mm
Size 13
22.2 mm
Size 9.5
19.4 mm
Size 10
19.9 mm
Size 6.5
16.9 mm
Size 10.5
20.2 mm
Size 7
17.3 mm
Size 11
20.6 mm
Size 8
18.2 mm
Size 7.5
17.7 mm
Size 11.5
21 mm