1. No category

How to add cameras according to each CMS via ONVIF, RTSP
ONVIF_ver0.00.09
CMS
company
Product
Version
Protocol
If you can't access stream of camera using Onvif, Please check the following two conditions.
1
Milestone
(Server /Client)
XProtect Go
ver2.0a
GeoVision
GV-NVR
ver8.5
page
1
ONVIF
2
ONVIF
8
RTP/RTSP
11
ver3.5.20
ONVIF
15
ONVIF
20
RTP/RTSP
24
2
3
4
NUUO
5
Digifort
Enterprise
ver6.5
6
ExacqVision
ExacqVision Client
ver4.8.11
7
Luxriot
Luxriot
ver2.0.2.1530
ONVIF
26
8
Axxon
AxxonSmart CMS
ver2.1.1
ONVIF
35
9
Qnap
ONVIF
39
10
Mirasys
DVMS
ver5.12.4
ONVIF
43
11
EverMedia
NV5000 Series
ver7.7.0.0.127SP4
RTP/RTSP
47
0
`
If you can't access stream of camera using Onvif, Please check the following two conditions.
- First,
Unckeck
- Second,
"Use Security on Onvif" and Save
Unckeck
"Use Authentication" and Save
1
`
1. How to add camera on Milestone XProtect Go via Onvif
1.
Run XProtect Go
Click mouse
2.
"XProtect Go Management Application"
Add Device Step 1
Click mouse
"1.Add Hardware Devices..."
2
`
3.
Add Device Step 2
Check "Manual", and Click mouse "Next"
4.
Add Device Step 3
Check "Use", Fill "Address , Port, User Name, Password",
Select Hardware Driver "ONVIF Conformant Device(2-16 channel)",
Click mouse
"Next"
3
`
5.
Add Device Last
Check "Finish"
6.
Add Device with RTP/RTSP/TCP -- Step 1
Double Check "Camera 1"
4
`
7.
Add Device with RTP/RTSP/TCP -- Step 2
Check "Video", and Check "Configure Video properties"
8.
Add Device with RTP/RTSP/TCP -- Step 3
Select "Protocol - RTP/RTSP/TCP", and Click "OK"
5
`
9.
Finish Job
6
`
Milestone Client Issue
if you see like this message "The server has lost connection to the camera"
on the Milestone Client.
Uncheck "Microphone"
Restart Application.
7
`
2. How to add camera on GeoVision GV-NVR via Onvif
1.
Run GV-NVR
2.
Configure  System Configure  IP Camera Install
4.
Click “Add Camera” on IP Device Setup page
8
`
On Select Brand window
Enter Server IP, HTTP Port, User name, Password
On Brand, choose Protocol
On Device, choose ONVIF
5.
Choose Codec and Click “Apply”
9
`
6.
After finding the camera, click the right button of mouse
Change position -> choose the camera position
7.
After confirming the camera, Click “OK”
8.
Checking the picture
10
`
3. How to add camera on GeoVision GV-NVR via RTP/RTSP (RTP/TCP)
1.
Run GV-NVR
2.
Configure  System Configure  IP Camera Install
3.
Choose “Add Camera” on IP Device Setup window
11
`
4.
On Select Brand window
Enter Server IP, HTTP Port, User name, Password
On Brand, choose “Protocol”
On Device, choose “RTSP over TCP”
5.
After entering RTSP command, Click OK
12
`
6.
After entering RTSP Port, Click “Apply”
7.
After finding the camera, click the right button of mouse
Change position  Choose the camera position
8.
After confirming the camera and click “OK”
13
`
9.
Checking the picture
14
`
4. How to add camera on NUUO NVR via Onvif
1.
Run NVR
Click mouse
"NUUO Main Console"
Click mouse
"Input ID/Password"
15
`
2.
Add Device Step 1
Check "General Setting"
3.
Add Device Step 2
Click "Setting"  Click "System Setting"
16
`
4.
Add Device Step 3
Fill in the blank item, "Name, IP Address, Http Port, User Name, Password ", and
Check Protocol "TCP or UDP", We are not support HTTP now.
Select Vendor "ONVIF". Press alphabet 'o' or 'O', you can select more easily.
17
`
5.
Add Device Last
Click "Yes or OK " button
18
`
6.
Finish Job
19
`
5. How to add camera on Digifort CMS via Onvif
1.
Run Enterprise Administration Client
2.
Choose Digifort Servers  Click Add Server  Register the server
3.
Double click the server  Enter ID/ Password
20
`
4.
Choose Recording Server  Cameras, Click Add
5.
Fill in Camera Name, Camera Description
Choose Manufacturer ONVIF
Fill in Recording Directory
21
`
6.
Fill in Camera Address, Port, User, Password
Click OK
7.
Check if it is working well at Recording Server  Status
22
`
8.
Run Digifort Enterprise Surveillance Client
23
`
6. How to add camera on ExacqVision CMS via RTP/RTSP
1.
Start ExacqVision Client
2.
Make sure that server is connected (Add Server)
3.
IP camera -> fill in username / password
4.
Hostname/IP Address -> rtsp://<IP address>/stream1 (i.e rtsp://10.1.10.10/stream1)
5.
Click “Apply”
6.
Make sure that camera is connected
24
`
7.
Camera Recording Setup -> Make sure that “video detected” appeared as “Yes”
8.
Select the camera that you registered. You will see live picture like below.
25
`
7. How to add camera on Luxriot CMS via Onvif
1.
Run Luxriot CMS
Click mouse
2.
"DVR Client"
Add Device Step 1
Mouse Right-button Click "Video" and Click "Camera Setup Wizard"
26
`
3.
Add Device Step 2
Click "Next"
4.
Add Device Step 3
Click "Network Devices(IP Camera, Video Server)" and Click "Next"
27
`
5.
Add Device Step 4
Fill in the "Device title" , Click "Properties"
28
`
6.
Add Device Step 5
Click "Generic"
 Click "ONVIF Compatible"  Click "Apply "
29
`
7.
Add Device Step 6
Fill in the blank item, "IP Address, Http Port, User Name, Password ",
then, Click "Apply "
30
`
8.
Add Device Step 7
Click "Next"
31
`
9.
Add Device Step 8
Click "Next"
10. Add Device Step 9
Click "Next"
32
`
11. Add Device Step 10
Click "Next"
12. Add Device Step 11
Click "Finish"
33
`
13. Finish Job
34
`
8. How to add camera on Axxon Smart CMS via Onvif
1.
Run AxxonSmart CMS
Click mouse
"Axxon Smart "
Check Server Name and Fill in the "Input ID/Password". default value is root/root
35
`
2.
Add Device Step 1
Click "
3.
".
Add Device Step 2
Click "Devices"  Click "
"
36
`
4.
Add Device Step 3
Fill in the item, "IP Address, Http Port,ID, Name", and
Check Produced by "ONVIF". ". Press alphabet 'o' or 'O', you can select more easily.
Click "Apply".
37
`
5.
Add Device Last ( Apply ID/PW for RTSP)
Fill in the "Login ID and Password". and Click "Apply".
6.
Finish Job
38
`
9. How to add camera on Qnap NVR via Onvif
1.
Run Qnap NVR
Type address of NVR on web-browser. and Input ID/Password.
39
`
2.
Add Device Step 1
Click "System configuration". and Input ID/Password.
3.
Add Device Step 2
Click "Camera Settings"
40
`
4.
Add Device Step 3
Select Camera Number for addition.
Fill in the blank item, "Camera Name, IP Address, Port (Web), User Name, Password ".
Select Brand "ONVIF".
Click "Test" button, if you set all information.
If test is ok, click "Apply" for saving information.
41
`
5.
Finish Job
42
`
10. How to add camera on Mirasys DVMS via Onvif
1.
Run DVMS
Click mouse
"DVMS System Manager"
Fill in the blank item "User name, Password". Default is "Admin/0308"
Click "
"
43
`
2.
Add Device Step 1
", Recorders
Check "
Click "
Click "
3.
Hardware " and
"
Add Device Step 2
Select Model "Automatic Camera search", and
Fill in the item, " IP Address, Http Port, User Name, Password ", and
Click "
"
44
`
Wait until finish job. if cms find any camera, then display like below picture.
Click "
"
45
`
4.
Finish Job
46
`
11. How to add camera on EverMedia HybridDVR via Onvif
1.
Run NV5000
2.
Once software and driver are installed, go to “Setup”
Select “IP camera”
and click “ADD IPCam” button.
Note : Since RTSP/RTP doesn’t support motion detection from camera, you have to use
motion detection feature from software. Please, go to “motion recording” section for
reference. “Detail” feature doesn’t work when camera is connected through RTSP.
47
`
3.
Select protocol “RTSP_RTP” and Model “TCP”
IP Camera Site:
rtsp://192.168.1.30/stream1 : 554 (RTSP Port Number)
Click “Authentication” and Input
ID and Password ( default : admin / admin)
Click “Connect”.
If you see live picture, click “Save & Exit”
48
`
Motion Recording
1.
Go to “Setup” and “Recording”
2.
Click “Advanced”
49
`
3.
Select “Region”
50
`