INTELLINET NETWORK SOLUTIONS Network Cameras - How To VIEW In Digifort

INTELLINET NETWORK SOLUTIONS Network Cameras
- How To VIEW In Digifort Digitfort consists of two main components.
1. Digifort Server (managed by the Administration client)
2. Digifort Surveillance Client
The camera setup is done in server administration client. The camera images can be viewed
in the surveillance client. On the pages below you can find information about how to set up
different INTELLINET network cameras to operate with the Digifort software.
We are not explaining how to use the Digifort software, however. For detailed information
about the use of this software you will need to refer to the documentation provided with
Digifort.
http://www.networkipcamera.com
INTELLINET NETWORK SOLUTIONS Network Cameras
- How To VIEW In Digifort Open the administration client.
Click on the “+” in front of “recording server”. A sub-menu will open up.
Select “Cameras”.
Click on “Add” to create a new camera.
http://www.networkipcamera.com
INTELLINET NETWORK SOLUTIONS Network Cameras
- How To VIEW In Digifort 1. Adding a JPG CMOS Camera (550710/550703/550550/550734)
You need to know the following:
a) IP address (or web address) of your camera
b) The Image Transfer Port that your camera is set to
That information can be obtained from the camera’s network configuration page. See the
example below:
IP Address: 10.10.8.215
Image Transfer Port: 8081
in Digifort:
Select the Camera Model “Intellinet INT-550710”
http://www.networkipcamera.com
INTELLINET NETWORK SOLUTIONS Network Cameras
- How To VIEW In Digifort Click on the RECORDING tab and fill out the information as shown below:
Next, click on the LIVE VISUALIZATION tab:
Either you activate the option (x) Access via relay server, or you specify the IP
information manually.
http://www.networkipcamera.com
INTELLINET NETWORK SOLUTIONS Network Cameras
- How To VIEW In Digifort Open the MEDIA PROFILES tab, click on RECORDING and MODIFY, as shown below:
Verify the video compression. It must be set to “Motion JPEG”. Adjust the frame rate of
the recordings and click on the preview button to check the live image. Click OK when
done. Repeat the procedure for the Visualization profile.
Click OK when done and you’ll be looking at the main screen of the administration client.
http://www.networkipcamera.com
INTELLINET NETWORK SOLUTIONS Network Cameras
- How To VIEW In Digifort -
Right-click the camera and select ACTIVATE CAMERA.
Next, switch to the Surveillance client.
The camera you
have added now
shows up in the
list.
You can drag
and drop the
camera onto the
view area to
display the live
video stream.
http://www.networkipcamera.com
INTELLINET NETWORK SOLUTIONS Network Cameras
- How To VIEW In Digifort 2. Adding a fixed CCD, Digital PTZ CMOS and Fixed Dome Camera
Fixed Dome Network Cameras
Fixed Indoor Cameras (CCD, Digital PTZ, Infrared and Wireless)
Be sure to have the latest firmware version on your camera installed.
You need to know the following:
a) IP address (or web address) of your camera
b) The Image Transfer Port that your camera is set to
That information can be obtained from the camera’s network configuration page. See
previous chapter.
All of these cameras support two kinds of video streams: Motion-JPEG (M-JPEG) and
MPEG4. You can choose the format you wish to use with Digifort. MPEG4 is the preferred
method as it provides higher image frame rates at a much lower bandwidth utilization.
You can define the video output stream type in the system settings of the camera. See
below:
http://www.networkipcamera.com
INTELLINET NETWORK SOLUTIONS Network Cameras
- How To VIEW In Digifort First example:
Digital PTZ Camera 550468, MPEG4 Streaming
Select the Camera Model “Intellinet INT-550468”.
Enter the Camera Address, the web port (standard 80), and also ADMIN USERNAME AND
PASSWORD (important!).
http://www.networkipcamera.com
INTELLINET NETWORK SOLUTIONS Network Cameras
- How To VIEW In Digifort Click on the “media profiles” tab.
You must select MPEG-4. Click on “Preview” to check the live image. Click OK when done.
Repeat the procedure for the recording profile.
http://www.networkipcamera.com
INTELLINET NETWORK SOLUTIONS Network Cameras
- How To VIEW In Digifort The next step is to activate the camera ….
… and assign it to a view:
http://www.networkipcamera.com
INTELLINET NETWORK SOLUTIONS Network Cameras
- How To VIEW In Digifort If you set your network camera to M-JPEG streaming, e.g., to remain compatible to web
browser access with Firefox or any Java compatible web browser, the procedure is very
similar, yet there are some differences.
In this example, we’ll add an IR Night Vision CCD Camera, model 550314 that is set to
Motion-JPEG mode.
Add a new camera to Digifort. Select the Camera Model “Intellinet INT-550314”.
Afteer that, click on the recording tab.
Enter the Camera Address, the web port (standard 80), and also ADMIN USERNAME AND
PASSWORD (important!).
http://www.networkipcamera.com
INTELLINET NETWORK SOLUTIONS Network Cameras
- How To VIEW In Digifort -
Verify the video compression. It must be set to “Motion JPEG”. Adjust the frame rate and
click on the preview button to check the live image. Click OK when done. Repeat the
procedure for the recording profile.
http://www.networkipcamera.com
INTELLINET NETWORK SOLUTIONS Network Cameras
- How To VIEW In Digifort The next step is to add the camera to the view, just as before.
When all done, it will look like this:
3. Final Comments
Technical support for the Digifort software is provided exclusively by the company
Logiware.
If you are having difficulties adding your INTELLINET NETWORK SOLUTIONS camera to
this software, please always make sure that you can access the camera with your web
browser without any problems. Furthermore please check and make sure that the web
server port and image transfer port are entered correctly.
Please also note, that the display performance (image frame rate) of your INTELLINET
camera can be significantly lower when viewed with this software compared to the web
browser access method. A demo version of this software is provided by the software
vendor which shall be used to evaluate the performance before a purchase of the
software is being made.
Technical support for our network cameras is provided at
http://www.networkipcamera.com.
http://www.networkipcamera.com