Keg King Retro Fitted Power Down Switch. (any
Keg King www.kegking.com.au The Keg Dispense Specialists 2/33-35 Smith Rd Springvale, VIC, 3171 Phone: +61 3 9011 1698 Fax: +61 3 9011 1697 How to set up 10amp Temp Controller for Distillation – With retro fitted power down switch. Retro Fitted Power Down Switch. (any 240V switch can be used here. Can purchase from Jaycar for couple of dollars) Installing a temp controller with a power down switch will mean that when your 10amp temp controller reaches a specific temperature the temp controller will turn off completely and not turn back on again until you reset the controller using the switch again. Below is the standard wiring for the 10amp temp controller. Below is the modified wiring diagram with the retro fitted power down switch. As you can see from the diagram above the temp controller power will be off until the retro fitted switch is turned on. Once the relay to power up terminal 1 of the temp controller is activated the retro fitted switch can be turned off. This will mean that you can leave the temp controller to complete the distillation process and when the target temperature that you set in the controller is reached the element and temp controller will all power down and not turn back on again. This is perfect if you want to automate the distillation process. Page 1 of 4 Keg King www.kegking.com.au The Keg Dispense Specialists 2/33-35 Smith Rd Springvale, VIC, 3171 Phone: +61 3 9011 1698 Fax: +61 3 9011 1697 FYI. The below function settings are recommended for the 10amp temp controller when distilling: E1 E2 E3 E4 E5 HC Function Set Range Lowest Temp. Limit ≥ -45 C Recommended 0 0 -45 C 0 Highest Temp. Limit ≤ 120 C Temp. Hysteresis 1 ~ 30 C 0 120 C 0 0 1C Start Delay Time 0-10min Temperature Calibration -19.9 C~20.0 C 0 Temperature Control Mode C=Cool,H=Heat H 0 0 min 0 Table 2.0 Page 2 of 4 Keg King www.kegking.com.au The Keg Dispense Specialists 2/33-35 Smith Rd Springvale, VIC, 3171 Phone: +61 3 9011 1698 Fax: +61 3 9011 1697 How to set up 16amp Temp Controller for Distillation – With retro fitted power down switch. Retro Fitted Power Down Switch. (any 240V switch can be used here. Can purchase from Jaycar for couple of dollars) Installing a temp controller with a power down switch will mean that when your 16amp temp controller reaches a specific temperature the temp controller will turn off completely and not turn back on again until you reset the controller using the switch again. Below is the standard wiring for the 16amp temp controller. Below is the modified wiring diagram with the retro fitted power down switch. As you can see from the diagram above the temp controller power will be off until the retro fitted switch is turned on. Once the relay to power up terminal 4 of the temp controller is activated the retro fitted switch can be turned off. This will mean that you can leave the temp controller to complete the distillation process and when the target temperature that you set in the controller is reached the element and temp controller will all power down and not turn back on again. This is perfect if you want to automate the distillation process. Page 3 of 4 Keg King www.kegking.com.au The Keg Dispense Specialists 2/33-35 Smith Rd Springvale, VIC, 3171 Phone: +61 3 9011 1698 Fax: +61 3 9011 1697 FYI. The below function settings are recommended for the 16amp temp controller when distilling: Function E1 E2 E3 E4 E5 CF C1 P1 P2 P3 P4 Set Range Lowest Temp. Limit ≥ -45 C Highest Temp. Limit ≤ 120 C Temp. Hysteresis Recommended 0 0 -35 C 0 0 100 C 0 0 0.1 ~ 30 C 0.1 C Cooling Delay Time 0-10min Temperature Calibration -19.9 C~20.0 C 0 0 min Temperature Unit 0 Operation Mode Switch Delay Time High Temp Alarm 0~30min 0 0 0 0 C OR F C 0min 0 0 0 0 -40 C~120.0 C 0 120 C 0 Low Temp Alarm -40 C~120.0 C -40 C Alarm Delay Time 0~90min 0min Alarm Hysteresis 0 0.1~30 C 0 0C Table 2.0 Page 4 of 4
© Copyright 2024