WSW sample cooler WSW Sample cooler For High Viscosity/Low Pressure Drop Service Efficient sample cooling for high viscosity liquids and slurries Features Description  Fully drainable helical coil The WSW series sample cooler is designed for use in applications where drainability is critical but efficiency cannot be compromised. Its larger diameter sample tube makes it especially useful for high viscosity liquids and slurries. Optimal service for flows below 3000 cc/ minute for single phase heat transfer. Standard tube side material is 316/316L stainless steel.  Low pressure drop Performance Curve - Water Model WSW-8222 Surface Area 2.5 Ft.2 [0.23 m2] 12 GPM [45 L/min] Cooling Water at 95oF [35oC] 7 PSI [0.48 Bar] Pressure Drop su re (P SI ) 0o F 15 20 0.4 10 10 0.2 40 30 Dr op 50 20 oF 0 30 o ) 9C (14 0.6 o C) 3 o F (9 200 5 Tem Inlet 1 PSI = 0.069 Bar Approach Temperature (oC) Approach Temperature (oF) es Pressure Drop (PSI) Pr ) e 40 60 o C) pl (2 25 0 (2 04 o C Sa m 0o F 50 NOTE: Not recommended for steam condensing service. See TLR, FLR, FXR series sample coolers for steam applications. o C) o F (66 p. 150 0 0.8 400 800 0.1 40 0.2 80 1200 0.3 120 160 1600 CCM 0.4 200 2000 0.5 0.6 GPM 240 Lbm/Hr Flow Rate www.sentry-equip.com 2400 280 2800 0.7 320 360 3200 0.8 400 4.7 Rev. 7 09/13 Specifications – WSW Series Tube ShellPart Model No. Shell Design Tube DesignMaterialMaterialArea Weight Number WSW-8222 400 psi @ 350ºF 27 bar @ 177ºC 1200 psi @ 650ºF 82 bar @ 343ºC 304 SS 316/316L SS 1/2" O.D. x 0.035"AW 2.5 ft2 0.23 m2 25 lbs 11.5 kg 7-00712A WSW-8222U 400 psi @ 350ºF 27 bar @ 177ºC 1200 psi @ 650ºF 82 bar @ 343ºC 304 SS 316/316L SS 1/2" O.D. x 0.035"AW 2.5 ft2 0.23 m2 25 lbs 11.5 kg 7-00712G NOTE: • U in model number denotes ASME stamped model. • Canadian Registration Number available for ASME models only. Consult factory for CRN and other options and information. • Vessels are exempt from CE marking per PED 97/23/EC, TÜV. Vessels are below or equal to the limits set forth in Article 3, Sections 1.1, 1.2, 1.3 and Section 2 as applicable, and are designed and manufactured in accordance with sound engineering practice (meets the general requirements of the ASME Section VIII, Division 1, Boiler And Pressure Vessel Code). Nameplate will bear the name of Sentry Equipment Corp and safety instructions will be included per Article 3, Section 2. It is solely the responsibility of the end-user, through its own analysis and testing, to select products and materials suitable for their specific application requirements, ensure they are properly installed, safely applied, properly maintained, and limit their use to their intended purpose. Improper selection, installation, or use may result in personal injury or property damage. SENTRY EQUIPMENT CORP For further information, contact: 966 Blue Ribbon Circle North Oconomowoc, WI 53066 USA Tel: 262-567-7256 • Fax: 262-567-4523 E-mail: [email protected] Website: www.sentry-equip.com © Sentry Equipment Corp 2010 4.7 Rev. 7 09/13