Standard materials Compact, efficient sample cooling for gases and liquids Performance Curve - Water Formed shell eliminates top shell flange weld interfaces Model TSR-4225 50 80 45 70 60 50 Sa m pl eP re s su 40 re Dr op (P SI ) 5 35 30 25 40 30 20 10 10 o o 0 40 F (2 04 C) 20 20 15 10 30 o ( 0F 14 oF 20 0 5 o ) 9C 25 o ) (93 C Inlet Te o o F (66 C) mp. 150 0 30 400 600 0.1 800 0.2 60 www.sentry-equip.com 15 1 PSI = 0.069 Bar 90 0 ) 55 Pressure Drop (PSI) NOTE: Not recommended for steam condensing service. See TLR, FLR, FXR series sample coolers for steam applications. 100 0o C bracket can be installed without removing flange bolts Approach Temperature (oF) Mounting Surface Area 1.2 Ft.2 [0.11 m2] 5 GPM [18.9 L/min] Cooling Water at 95oF [35oC] 3 PSI [0.20 Bar] Pressure Drop (2 6 shellside gasket reduces re-assembly time (3 16 o C) Retained 50 0o F variety of exotic alloys for corrosion resistance 371 o C) Wide The TSR series sample cooler is a compact sample cooler that provides broad application flexibility through the use of a variety of sample tube materials. Optimal service for flows below 1200 cc/min for single phase heat transfer. Standard tube side materials are 316/316L SS and Alloy (Inconel®) 625. See data sheet 4.8 for special materials available. 60 0o F helical coil design 700 o F( Single Description Approach Temperature (oC) Features 80 1000 1200 CCM 1400 0.3 GPM 1600 0.4 1800 2000 0.5 100 120 140 160 180 200 220 240 260 280 Lbm/Hr Flow Rate 4.2 Rev. 4 06/10 TSR sample cooler (Standard Materials) TSR Sample cooler 1 1/4 in. [32 mm] 13/16 in. [21 mm] 3/4 in. [19 mm] 4 7/8 in. [124 mm] 1/4 in. [6 mm] 1/2 in. FNPT cooling water outlet 4 7/8 [124 mm] SAMPLE OUTLET SAMPLE INLET 4 3/8 in. [111 mm] 4 1/4 in. [108 mm] 2 1/4 in. [57 mm] 1/8 in. [3 mm] 11 3/16 in. [283 mm] 3 5/16 in. [84 mm] 2 7/16 in. [61 mm] MOUNTING BRACKET 3/4 in. FNPT cooling water inlet (SUPPLIED WITH EACH COOLER) Specifications – TSR Series Model No. Shell Design Tube Design Tube Material Shell Material Area Shipping Weight Part Number TSR-4225 450 psi @ 650ºF 31 bar @ 345ºC 5000 psi @ 1000ºF 345 bar @ 540ºC 316/316L SS 1/4” O.D. x 0.049"AW 304 SS 1.2 ft2 0.11 m2 14 lbs 6 kg 7-03952A TSR-4225U 450 psi @ 650ºF 31 bar @ 345ºC 4400 psi @ 1000ºF 303 bar @ 540ºC 316/316L SS 1/4” O.D. x 0.049"AW 304 SS 1.2 ft2 0.11 m2 14 lbs 6 kg 7-03952B TSR-42B5 450 psi @ 650ºF 31 bar @ 345ºC 5000 psi @ 1100ºF 345 bar @ 593ºC Alloy (Inconel®) 625 1/4” O.D. x 0.035"AW 304 SS 1.2 ft2 0.11 m2 14 lbs 6 kg 7-03952C TSR-42B5U 450 psi @ 650ºF 31 bar @ 345ºC 5000 psi @ 1100ºF 345 bar @ 593ºC Alloy (Inconel®) 625 1/4” O.D. x 0.035"AW 304 SS 1.2 ft2 0.11 m2 14 lbs 6 kg 7-03952D TSR-4BB5 450 psi @ 650ºF 31 bar @ 345ºC 5000 psi @ 1100ºF 345 bar @ 593ºC Alloy (Inconel®) 625 1/4” O.D. x 0.035"AW Alloy 1.2 ft2 (Inconel®) 625 0.11 m2 14 lbs 6 kg 7-03952E NOTES: • U in model number denotes ASME stamped model. • Canadian Registration Number available for ASME stamped models only. Consult factory for CRN and other options and information. • Vessels are exempt from CE marking per PED 97/23/EC, TÜV. Vessels are below or equal to the limits set forth in Article 3, Sections 1.1, 1.2, 1.3 and Section 2 as applicable, and are designed and manufactured in accordance with sound engineering practice (meets the general requirements of the ASME Section VIII, Division 1, Boiler And Pressure Vessel Code). Nameplate will bear the name of Sentry Equipment Corp and safety instructions will be included per Article 3, Section 2. It is solely the responsibility of the end-user, through its own analysis and testing, to select products and materials suitable for their specific application requirements, ensure they are properly installed, safely applied, properly maintained, and limit their use to their intended purpose. Improper selection, installation, or use may result in personal injury or property damage. SENTRY EQUIPMENT CORP For further information, contact: PO Box 127 Oconomowoc, WI 53066 USA Phone: 262-567-7256 Fa x: 262-567-4523 E-mail: [email protected] Website: w w w.sentry-equip.com ISO 9001:2008 © Sentry Equipment Corp 2010 4.2 Rev. 4 06/10