Warranty Statement The Lumitex Mytilux downlight range is warranted to be free from defects in material and workmanship and to operate from the date of installation (or date of manufacture if installation date is not known or available) for a period of 5 (Five) years subject to the terms and conditions below. If the product fails to operate for the warranty period, Lumitex will provide a free replacement product. Any costs associated with the removal or installation of the product are the user's responsibility. The benefits provided to the consumer by this warranty are in addition to other rights and remedies available to the consumer under the law. Lumitex Limited 16 Runyon Road, Midvale WA 6056 Toll Free: 1300 337 809 Email: [email protected] M Lumitex High Performance LED Downlight Owner’s Manual Warranty terms and conditions: 1) Proof of Purchase must be provided. 2) After contacting Lumitex Limited and receiving a return authorization number, the user shall promptly return the product at the user's expense to Lumitex Limited after receiving instructions as to if, when and where to send. No Heat Shield Required 3) Lumitex Limited reserves the right to examine all failed products and reserves the right to be the sole judge as to whether the products are defective and covered under this warranty. 4) Due to the rapidly changing technology environment surrounding LED Lighting, Lumitex Limited reserves the right to replace products with later model upgraded equivalents where in some cases appearance may differ slightly from the original. 5) Failure to observe correct installation practices as detailed within this manual may void the warranty. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Version 1.1 2014_04_15 www.lumitex.com.au Lumitex LED Lighting LED Downlight Manufacturer's Installation Instructions TM Lumitex Ltd ACN: 075 108 566 Technical Support Hotline - 1300 337 809 ® ® 5531 Thank you for purchasing the Lumitex Mytilux, an innovative LED lighting solution. A five year Warranty applies to this product range. You have chosen a quality product that has been assembled with carefully selected components to create a safe, high performance light source with exceptional dimming performance capability. ® Mytilux will provide illumination exceeding the quality and reliability of halogen. This LED downlight, when installed according to the manufacturer's instructions below, complies with AS/NZS 3000:2007 Amendment 2, specifically including Clause 4.5.2.3.1 (i) (A+B) Electrical Rating: 220V-240V~50Hz Power factor and current: 0.93, 0.05A Driver Ta: 50°C Max IP54 After installation Suitable for bathrooms ® Mytilux incorporates an extendable arm to suspend the driver electronics above your home’s insulation. This serves two purposes: to facilitate simple installation from within the room, while also ensuring free air circulation around the driver that will assist to further extend its operating life. Extensive testing supported by accredited laboratory reports allow Mytilux to be installed without a heat shield. This will save you the purchase cost of, as well as the labour, to install the heat shield. ® Suitability for use: "Indoors." (Or, suitably protected from weather in outdoor living areas) Testing Standard: This product has been tested to AS/NZS 60598.2.2:2001 and AS/NZS 60598.1:2013, verifying the luminaire will not exceed 90°C under normal conditions when in contact with timber or covered with insulation as shown in the diagram and installed according to the installation instructions below. No heat shield is required. We appreciate your support of our 100% Australian owned company through this purchase. Installation Instructions Mytilux ® has been tested to be safe when in contact with roof timber. Yours sincerely, The Lumitex Team Insulation contacting the fixture may result in an elevated temperature of the heatsink but this does not affect the Warranty of the product nor will it exceed the safe operating temperature of the luminaire. Ÿ All electrical work to be undertaken by a licensed electrician. Minimum clearance 20mm Insulation Driver Ensure driver is extended above insulation Ÿ Cut the hole to 95mm diameter. Ÿ The driver must be located above any insulation. Extend the driver arm and position the driver to avoid obstructions and insulation in the roof space. Ÿ Mytilux can be used in slab canisters. There is no need to extend the driver arm ® when used in slab canisters. Extend arm to 160mm ® ® Roof Timber Ceiling LED dimmer, Clipsal® Universal rotary wall dimmer or C-Bus Universal dimmer. Please see the website for the latest details on other compatible dimming systems, including those of HPM®. Ÿ If dimming is required, please connect to a Lumitex Ÿ If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.