1. No category

45H/47H Drilling Instructions/Template
1-1/16"
27 mm
Auger Bit
1"
25 mm
Auger Bit
1/8"
3.2 mm
Drill Bit
•
5/32"
4 mm
3/8"
9.5 mm
3/4"
19.1 mm
Chisel
5/8"
16 mm
•
•
•
•
4
Connect previous
marks.
7
Trace Lockset face.
•
Visual Indicator Thumb Turn
5
* † ‡ †† See Notes on second page.
J&K
•
•
*H & R trim visual indicator (2)
•
Align template
with the lever
centerline and
centerpunch
corners of box L.
L
J
•
††Lever (1)
H
•
††Trim mounting (2)
G
3
Center punch
holes
according to
Model Chart.
1"
25 mm
4-1/4"
(108 mm)
deep
6
Auger Bit
A
Align to Low Edge (narrow side)
1-1/4" (31.8 mm)
B
1-1/4" (31.8 mm)
N
1-1/8" (28.6 mm)
Strike
Strike
Lock
J
E
F
1/2"
12.7 mm
3-3/8" (85.7 mm)
3/8"
9.5 mm
G
Lever
N
C
Lock
7/8"
22.2 mm
Lever
3/4"
19.1 mm
4-1/8" (104.8 mm)
O
K
1-1/4"
31.8 mm
J
E
Strike
Lock
4-7/8" (124 mm)
D
1-3/4"
44.5 mm
1-1/16" (27 mm)
3/8"
9.5 mm
K
ENSURE
SQUARE IS
1"(25.4mm)
AFTER PRINT.
5/8"
15.9 mm
H
G
A
L
1-1/8" (28.6 mm)
3/32"
2.4 mm
4-7/8" (123.8 mm)
•
•
•
•
•
2
1-49/64" (44.8 mm)
•
•
Place the template on the exterior edge of door and mark horizontal line for door edge
template based on hole H. Suggested height from bottom of the door to hole H is 39-9/16"
(1005 mm). Mark centerline of lockset on the door face and continued onto door edge.
•
•
•
•
•
•
•
•
•
•
•
#12-24 Tap Bit
Ø1-3/8"
35 mm
1
•
•
F
•
*H, R, & S trim thumb turn (2)
Emergency key/thumb turn access (1)
E
•
•
•
•
•
•
•
‡Cylinder (1)
High security cylinder (1)
C
D
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
#8-32 Tap Bit
Align to High Edge (wide side)
Ø 5/32"
4 mm
1"
25 mm
Spade Bit
1-1/4"
32 mm
Chisel
6-59/64" (178.9 mm)
•
†•
•
†Through Door
Through Door Through Door Through Door Through Door
*J trim (1)
Through Door Through Door
*M & N forged trim (2)
B
Through Door Through Door Through Door Through Door Through Door Through Door Through Door Through Door Through Door †Through Door
Tools Needed
Hole Saw
A
EX
IN
EX
IN
Holes
IN
EX
IN
EX
AB, AT, B, BA,
A, D R, RHB, BW, HJ, T, TA,
B5, DEL, DEU TD, TDEL,
TDEU
IN
AD
EX
IN
EX
C, CHB, G,
IND, INL, S,
W, B7, TWEL,
TWEU, WEL,
WEU
IN
H
EX
Functions
L, LB, LT, LEL, N, NX, NXEL,
LEU
NXEU
IN
RD, WD
EX
IN
YD
EX
IN
1DT, 2DT
EX
Spanish and French translations are available on www.bestaccess.com
Traducciones al español y francés están disponibles en www.bestaccess.com
Des traductions en espagnol et en français sont disponibles sur www.bestaccess.com
5/8"
15.9 mm
M
1/2
T81163-B Copyright© 2014 Stanley Security, Inc.
8
9
1/4"
6.4 mm
deep
10
Mark holes
1-1/4"
32 mm
Chisel
11
12
Metal Doors:
#12-24 Tap
5/32"
4 mm
13
Drill holes selected from Model
Chart based on your function.
Continue the lockset centerline
(located on template) onto the
door frame.
3/4"
19 mm
deep
14
15
Locate center of strike
hole by measuring back
from door stop, 1/2 the
thickness of door.
17
18
1"
25 mm
19
3/32" (2.4 mm)
deep
5/32" (4 mm)
deep w/ dust box
1-1/8"
(29 mm)
deep
16
Place strike template
centerline on lever
centerline made on the
previous step.
Centerpunch edges of
strike and box, O.
Connect
previous marks.
20
Mark holes
3/4" (19 mm)
deep
5/32"
4 mm
Metal Doors:
#12-24 Tap
1-1/4"
32 mm
Chisel
* For trim outside only functions (such as ZD and ZR) and trim inside only functions (such as XD and XR), prepare surface mount trim holes on the trim side of the door as needed.
† For 1DT, drill 7/64 in. (11 mm) holes halfway into the door at the centerpoints indicated.
‡ To qualify for the UL 437 high security listing, use the M escutcheon and the 1E7J4 cylinder. The1E7K4 cylinder is available for use with either M trim or sectional trim, but does not qualify for the UL 437 high security listing. This option is not
available for H and HJ function locks.
†† Because these holes pass through the mortise pocket, it is recommended that each hole be drilled separately rather than straight through.
Align to High Edge (wide side)
A
Align to Low Edge (narrow side)
1-1/4" (31.8 mm)
B
K
K
1-1/4"
31.8 mm
4-7/8" (123.8 mm)
C
J
D
J
E
F
1/2"
12.7 mm
ENSURE
SQUARE IS
1"(25.4mm)
AFTER PRINT.
1-3/4"
44.5 mm
E
Ø 5/32"
4 mm
1-1/16" (27 mm)
Strike
Strike
Strike
Lock
3-3/8" (85.7 mm)
Lock
3/8"
9.5 mm
G
7/8"
22.2 mm
N
1-1/8" (28.6 mm)
Lock
O
Lever
3/4"
19.1 mm
Lever
1-49/64" (44.8 mm)
6-59/64" (178.9 mm)
1-1/4" (31.8 mm)
H
4-7/8" (124 mm)
3/8"
9.5 mm
4-1/8" (104.8 mm)
5/8"
15.9 mm
N
G
A
L
5/8"
15.9 mm
M
2/2
3/32"
2.4 mm
1-1/8" (28.6 mm)
T81163-B Copyright© 2014 Stanley Security, Inc.