Technical Data Sheet Release 1: 25/01/2009 ® FINOMIX HYDROSEAL - HS 5000 FINOMIX® HYDROSEAL - HS 5000 Brushable cementitious sealing mortar. DESCRIPTION Brushable cementitious sealing mortar, enriched with polymer additives (resins). Composed of highperformance Portland cement, quartz aggregates of selective grain size, specially selected microsilicates, highly dispersed hydrophobic resins and other enhancing additives. It presents excellent bonding to typical substrates and excellent resistance to moisture and frost. APPLICATIONS Provides water-proofing on concrete surfaces in:  Basements  Water tanks  Foundations  Wells  Surfaces of concrete, plaster, bricks etc. to old and new constructions PROPERTIES     Excellent water-repellence. Suitable for positive and negative hydrostatic pressures. Very good resistance to moisture, solvents and alkali. Resistance to ageing. APPLICATION METHOD     Surfaces should be clean and free from dust, grease and other residual materials. Form wires exceeding from concrete should be cut 1.5-2.0 cm deep. Repair the cavities left, using the RP 4000 repairing mortar. Before application, all surfaces should be dampened well and excess water should be drained afterwards. Add the bag's content (25kg) into approx. 6.25-6.50kg of clean water under continuous stirring, until you obtain a uniform lump-free mixture. We recommend the use of a low speed power drill (300 r.p.m). Then, leave the mixture to mature for about 5-10 min. and stir again. The material is applied by brush or trowel in 2 or more layers, depending on the water effect. Apply each new coating when the previous has dried, but before it is completely hardened. If necessary, slightly dampen the previous layer but without flushing it. Successive layers should be applied crosswise, ensuring that any gaps are fully covered. ELASTIFICATION - REINFORCEMENT The addition of 3-6kg of FINOFLEX replacing part of the mixing water of HS 5000 can significantly enhance the final product's properties, such as wear resistance, bonding, water impermeability, flexibility etc. RECOMMENDATIONS  Do not mix the product with dirty or salty water. FINOMIX® HYDROSEAL - HS 5000 1/3   During the application, temperature should be between +5ºC and +35ºC. At high temperatures or strong winds, make sure to dampen the surfaces after application, in order to prevent premature drying of the material which may compromise the properties of the product. TECHNICAL CHARACTERISTICS PROPERTY Form Color Bulk density of dry mortar. Mixing ratio. Mixture density. Mixture pH. Work time. Setting time Density of cured material. Compressive strength after dry storage. Flexural strength after dry storage. Strength development time. Shrinkage. Waterproofing Adhesion to the substrate Resistance to ageing Resistance to solvents and oils UNITS STANDARD kg/l l/kg kg/l min h kg/l N/mm2 N/mm2 EN 1015 - 9 ΕΝ 196-3 EN 1015 - 10 EN 1015-11 EN 1015-11 mm/M atm EN 12808 - 4 DIN 1048 VALUE Powder Grey / White 1.2-1.3 0.26 1.9 > 10 30 6 1.6-1.7 ≥ 250.0 ≥ 6.0 7 days Zero 7 Excellent Excellent Excellent Note: Measures were carried out in laboratory environment conditions (Temperature +22°C,R.H.: 60% with no ventilation). The different conditions in the manufacture plant (temperature, humidity, ventilation, substrate absorption) may affect the properties of the material. SAFETY PRECAUTIONS The product HS 5000 contains cement which reacts as alkaline with water and perspiration, and may cause allergies and/or irritation. Always wear appropriate personal protective equipment for eyes and skin (protective clothing, gloves and goggles). If skin contact occurs, rinse well with plenty of clean water. In case of eye contact, get medical advice immediately. CONSUMPTION Approx. 1.0-1.5 kg/m2 per coating 1mm thick. The total consumption and thickness of the material depend on the waterproofing requirements. SHELF LIFE At least 12 months from date of production when stored in original unopened packaging, in places protected from moisture and frost. WARNING The technical characteristics and recommendations for the use and application of the FINOMIX range of products are based on the knowledge and experience of the company. The above information shall be considered merely indicative and subject to confirmation after long-term practical application. For this reason, anyone who intends to use the product must ensure that it is suitable for the envisaged application. Since the specific site conditions during the applications are beyond the control of our company, the user alone is fully responsible for any consequences deriving from the use of the product. FINOMIX has the right to modify the FINOMIX® HYDROSEAL - HS 5000 2/3 properties of its products without prior notice. This release voids any previous publications issued for this technical specifications sheet. FINOBETON S.A. Pythagora 16, 73134 Chania - Crete Phone.: 28210 27000 , Fax: 28210 27005 E-mail: [email protected] www.finomix.gr FINOMIX® HYDROSEAL - HS 5000 3/3