Sync™ Project Name Spec Type Wall Notes Direct/Indirect 1 T8 Order Guide Some combinations of product options may not be available. Consult factory for assistance with your specification. 7408 – T01 – – – – Product Series & Type Lamping Lower Optics Upper Optics Run Length Wiring Voltage Ballast Color & Finish Sync Wall 1 T8 Q MesoOptics® Lens N None Enter the total run length in feet (4ft increments) 1 3 5 7 1 120V 2 277V E Standard Ballast W Standard White C Factory Color X Custom Color See details on reverse Consult website for complete list of standard wiring options Consult website for ballast manufacturer information Consult website for color and finish options Upgrades & Accessories Lamps Included 1 cct 1 cct w/ Emergency cct 1 cct w/ Battery Pack 1 cct Dimming Please indicate with check mark. Dust Cover 1-9/16" 6-1/16" © 2009 Ledalite Phone: 604.888.6811 Fax: 800.665.5332 Web: www.ledalite.com Filename 7408T01QN.pdf Rev 1.2 Sync™ Additional Information Wall Direct/Indirect Modules 1 T8 Module length excludes endcaps. Photometry Candela Distribution 0 5 15 25 35 45 55 65 75 85 90 95 105 115 125 135 145 155 165 175 180 0 387 406 458 500 404 250 154 84 33 3 0 110 295 424 517 498 452 380 301 229 193 Horizontal Angle 22.5 45 67.5 90 387 397 422 443 391 258 149 77 31 4 0 122 273 391 417 405 370 325 274 223 193 387 373 326 243 172 120 87 57 27 6 0 4 13 29 39 48 67 85 111 161 193 387 384 368 335 279 205 133 76 30 3 0 18 47 79 110 138 160 175 187 192 193 387 376 339 278 202 143 98 60 26 5 0 5 18 33 47 65 81 96 128 170 193 Zonal Lumens 135 135 90 90 600 cd Specifications 29 114 170 191 176 144 107 67 29 Avg. Luminance (cd/m2) 70 50 30 10 70 70 50 30 50 50 30 10 0 0 Vertical Angle 0 RCR 1 2 3 4 5 6 7 8 9 10 68 63 57 52 48 44 41 38 35 33 30 68 60 53 47 41 37 33 30 27 25 23 68 58 49 42 37 32 28 25 22 20 18 68 56 46 39 33 28 25 22 19 17 15 63 57 52 48 44 40 37 35 32 30 28 63 55 49 43 38 34 31 28 25 23 21 63 53 45 39 34 30 26 24 21 19 17 52 46 41 36 32 29 26 24 22 20 18 52 45 39 33 29 26 23 20 18 17 15 52 43 37 31 27 23 20 18 16 14 13 29 25 22 19 16 14 13 11 10 9 8 55 65 75 85 Phone: 604.888.6811 0 Horizontal Angle 45 90 3283 2430 1559 421 2835 2199 1417 421 1855 1649 1276 842 IES files for this and other photometric options can be downloaded online at www.ledalite.com Fax: 800.665.5332 Housing Die-formed 18 gauge cold-rolled steel. Weight 2.4 lb/ft. 52.1% Up / 47.9% Down Ceiling: Wall: © 2009 Ledalite 90-90 45-135 0-180 0 Based on a floor reflectance of 0.2 Due to continuing product improvements, Ledalite reserves the right to change specifications without notice. 45 45 Coefficients of Utilization (%) 80 For further details, refer to installation instructions online at www.ledalite.com 180 22 91 154 183 166 126 83 42 10 1/16" • Mounts variable within 2"-5" of end or joint. On 8ft module, additional mount to be located within 2"-5" of center of module. • Maximum distance between mounts is 48". Note: Fixture is flush with wall. * Between 90-180˚ vertical angle Meets RP-1-04 recommendations for VDT-Intensive spaces Vertical Angle Endcap Mounting Hardware Peak Candela Value* 527 @ 128° Peak to Zenith Ratio* 2.7 : 1 9901159 7408T01QN.ies 64.4% Nominal Length 4’ 0” 8’ 0” Refer to installation instructions for exact mount spacing Optics QN MesoOptics® Lens Report Summary Report # Filename Efficiency Module 4ft 8ft Web: www.ledalite.com Optical System High efficiency optical system providing an optimal asymmetric direct/ indirect distribution. Lower optics consist of a flat acrylic panel with a layer of MesoOptics® film that provides a controlled distribution in the lower hemisphere. Ballast Electronic. Supplied with pre-installed ballast disconnects as per changes to the National Electrical Code. Approvals Certified to UL and CSA standards. Finish High-quality powder coat. Available in Ledalite Standard White (textured matte finish), and a selection of other factory and customerspecified colors. Consult factory for details. Endcaps Die-cast endcaps. Joints Self-aligning joining system with hands-free pre-joining wire access. Mounting Fixture is mounted flush to wall using hidden wall brackets. Brackets attach to existing structure, variable within 2"-5" of end or joint. Electrical Factory pre-wired to section ends with quick-wire connectors. Filename 7408T01QN.pdf Rev 1.2
© Copyright 2024