1. No category

TCH
PHONE: 800-670-9475
FAX: 763-428-5111
www.twincityhose.com
RUBBER EXPANSION JOINTS
Twin City Hose rubber expansion joints are fabricated of natural or synthetic elastomers and fabrics.
Metal reinforcementcan be provided to accommodate extreme piping system stress.
FUNCTIONS
• Vibration isolation protects equipment and piping system
• Accommodates for directional movement such as axial, angular, lateral and torsional
• Reduces harmonics/sound transmitted down the pipeline by the pump or other equipment
• Compensates for misalignment as system and equipment move out of alignment due to operation and installation
These functions prevent equipment damage and costly downtime of plant operations.
ADVANTAGES
• Small face to face dimension, standard 6” OAL
• Cost effective compared to metal expansion joints
• Longer cycle life : vibration and harmonics are not a concern
• Lightweight : usually requiring no special equipment or handling for installation
• Resistant to abrasion and external damages : rubber is more forgiving than metal
• Low movement force with almost unlimited flexing and recovery from imposed movements
• Smaller OAL makes the rubber expansion joint economically superior to expansion loops or bends
SELECTION
• Twin City Hose offers optional 150# stainless steel or 300# carbon steel flanges
• Twin City Hose stocks single and double sphere, female union, spool type and eccentric rubber expansion joints
inboth EPDM and Neoprene
Other materials and styles are available
20615 Commerce Blvd. Rogers, MN 55374
[email protected]
1/2015
TCH
PHONE: 800-670-9475
FAX: 763-428-5111
www.twincityhose.com
RUBBER EXPANSION JOINTS
INSTALLATION
Alignment: Pipe misalignment should be no more than ⅛” in any direction
Anchoring: Expansion joints should be located as close as possible to anchor points. If anchoring system is not
used, it is recommended that control rods be installed on the expansion joint to prevent excessive movements
from occurring due to pressure thrust of the line.
Mating Flanges: Make sure mating flanges are clean and are flat faced type. Never install expansion joints next
to wafer type check valves or butterfly valves. Serious damage to the rubber flange bead can result due to lack
of flange mating surface and/or bolt connection.
See rubber expansion joint installation instructions at twincityhose.com/references for additional information
MS1
The MS1 is the most widely used rubber expansion joint and is very reasonably priced. Solid
plate flanges on each end are floating. Options for stainless steel 150# or carbon steel 300#
flanges are available. Neoprene and EPDM expansion joints are in stock.
MS2
The MS2 allows greater movement than the MS1 and is used in exactly the same way. Solid
plate flanges on each end are floating. Options for stainless steel 150# or carbon steel 300#
flanges are available. Neoprene and EPDM expansion joints are in stock.
MSFU
The MSFU is used for threaded union connections and has the same characteristics as the MS1
and MS2 but for smaller I.D. up to 2 ½”.
BODY CONSTRUCTION
MAXIMUM TEMPURATURE
DESIGN DATA MS1 - MS2 - MSFU
Neoprene Nylon
230 Degrees F
1) Temperature range 20°F to 250°F
EPDM Nylon
250 Degrees F
Butyl Nylon
250 Degrees F
Nitrile Nylon
230 Degrees F
2) Max negative pressure 26” HG Vacuum
3) Listed movements cannot occur simultaneously
Pressure rating is based on 170°F operating temperature
20615 Commerce Blvd. Rogers, MN 55374
[email protected]
1/2015
TCH
PHONE: 800-670-9475
FAX: 763-428-5111
www.twincityhose.com
RUBBER EXPANSION JOINTS
MRCE
•
Solid plate flanges on each end are floating for easy installation
•
Standard and custom sized I.D. and OAL are also available upon request
•
Options for stainless steel 150# or carbon steel 300# flanges are available
•
Concentric reducing expansion joints connect unequal pipe sizes that share the same center line.
Small Flange &
Retaining Ring O.D.
Small End
Nominal Pipe Size
Exp. Joint I.D.
lt
Bo le
c
Cir
Large End
Nominal Pipe Size
Exp. Joint I.D.
Retaining
Rings
Retaining
Rings
Bolt
le
Circ
Equally Spaced
Bolt Holes
S1
Spool type expansion joints provide double arch movements, utilizing a single low profile wide arch.
The construction combines woven polyester fabric and elastomer reinforced with wire to create a
product with superior performance. Flanges are integral with the body and utilize split metal retaining rings.
Standard and custom sized I.D. and OAL are available.
Custom Options:
•
Offset
•
Filled Arch
•
Multi Arch
•
Special Ends
•
Alternative Drilling
•
Full Range of Elastomers
•
Full Range of Retaining Rings
VIBRAPIPE
Rubber pipe is designed to absorb vibration and sound. They are furnished with molded rubber flanged ends with
split ring metal flanges and come with or without helical wire reinforcement.
•
Rubber pipe is not designed to accommodate axial movement
•
Standard and custom sized I.D. and OAL are available
•
Working PSI at 150 or 200 at 180°F or 250°F
20615 Commerce Blvd. Rogers, MN 55374
[email protected]
1/2015
TCH
PHONE: 800-670-9475
FAX: 763-428-5111
www.twincityhose.com
RUBBER EXPANSION JOINTS
CONTROL RODS
Control rods are designed to limit excessive movement to an expansion joint. When used they are an additional
safety factor, minimizing possible failure of the expansion joint or damage to equipment. They must be used in any
unanchored system or where pressures exceed stated pressure in chart #1.
CHART #1
Control units must be installed when pressures
(working, test, surge) exceed rating below:
Pipe
Size
NOMINAL PIPE
SIZE JOINT I.D.
STANDARD
PIPE FLANGE
STEEL
WASHER
RUBBER
WASHER
MS1
P.S.I.G
MS2
P.S.I.G
1” - 4”
180
135
5” - 10”
135
135
12” - 14”
90
90
16” - 24”
45
45
FLANGES
View from the top of flange
with attached control rods
OPTIONAL
COMPRESSION
SLEEVE
CONTROL
ROD PLATE
BOLT CIRCLE
FLANGE O.D.
CONTROL ROD BOLT CIRCLE
CONTROL ROD PLATE MAXIMUM O.D.
PTFE EXPANSION JOINTS
Constructed of molded PTFE, these joints provide exceptional corrosion
resistance and accommodatemovement within the system.
Benefits:
PTFE Expansion Joint Uses:
•
Noise reduction
•
Piping Systems
•
Convoluted design reduces vibration
•
HVAC Installations
•
Compensates for axial and lateral expansion
•
Corrosive Applications
•
Standard lengths are the shortest available for
•
Chemical and Petrochemical Industries
vibration isolation
AVAILABLE IN 2, 3, AND 5 CONVOLUTIONS
2 Convolutions
Available 1” - 12”
Movement
¼” - ½”
20615 Commerce Blvd. Rogers, MN 55374
3 Convolutions
Available 1” - 8”
Movement
½” - 1 ⅛”
5 Convolutions
Available 1” - 6”
Movement
½” - 1 ¼”
[email protected]
1/2015