TEMRO TEM/3800 Cold Weather Starting Products HEAVY DUTY COOLANT IMMERSION HEATERS Temro offers a wide variety of direct OEM immersion heaters. For specific application needs please 360-0015 consult Gregg Distributors or your newest Temro catalogue. Part No. 360-0015, Standard replacement cord for most OEM immersion heaters offered by Temro. Part No. 360-0014, Weatherproof receptacle and cordset for most OEM immersion heaters offered by Temro. MAGNETIC HEATER 200 watt 120 volt magnetic utility heater for use on engine blocks, oil pans, hydraulic cylinders, pipes, pumps, valves, etc. with built-in 121°C thermostat. Part No. 340-0017. OIL PAN HEATERS — CLAMP-ON Part No. 340-0011, 300 watt 120 volt 4” x 4” clamp-on oil pan heater. Part No. 340-0014, 500 watt 120 volt 6” x 6” clamp-on oil pan heater. Part No. 360-0002, Replacement power cord for oil pan heaters. OIL PAN HEATERS - HEAVY DUTY THREAD IN 120 volt oil pan heater. Part No. 220-1712, 1/2” NPT 150 watt - 7¾” long element. Part No. 220-1968, 3/4” NPT 300 watt - 11-1/8” long element. Part No. 220-4274, 1” NPT 150 watt - 6-5/8” long element. Part No. 220-0635, 1” NPT 150 watt - 5-5/8” long element. Part No. 220-2662, 1” NPT 300 watt - 6” long element - thermostatically controlled. Part No. 360-0015, Replacement power cord for 220-0635, 220-1968, 220-4274. Part No. 360-0002, Replacement power cord for 220-1712. DIESEL FUEL WARMER — HEAVY DUTY Stainless steel diesel fuel warmer utilizing a compact OEM approved design. Can be mounted horizontally or vertically. May also be used as a heat exchanger in certain hydraulic applications. Unit is designed for all heavy duty diesel applications. Part No. 820-8751. Automotive & Heavy Duty Fleet Products RADIANT TYPE HEATERS 300 watt 120 volt 3” x 7” oval radiant type clamp-on heater for small car application — universal bracket supplied. Part No. 340-0008. Part No. 360-0001, Replacement cord for 340-0008 radiant heater. 340-0014 220-1712 220-2662 STARTING FLUID SYSTEM E-Z stock ether injection kit. This kit will cover 90% of all class 7 and 8 vehicles having diesel engines 450 to 900 c.i.d. Kit comes complete with 3 atomizers, switch, valve fitting, 48” of nylon tube, dash decal, wire, thermostat, and all brackets required. Note: Ether bottle #820-0327 sold separately. Part No. 820-3237. STARTING FLUID SYSTEM ACCESSORIES Part No. 820-4209, Smartshot module - Smartshot is a fully electronic control system that eliminates starting fluid guesswork and abuse. Smartshot collects engine temperature data and electronically controls use of starting fluid. Unit will deliver fluid only when starter is engaged and only when fluid is required. Wires to most existing 12V measured shot systems. Part No. 820-3032, 1/4” NPT x 1/8” NPT bushing adapter for starting fluid atomizers. Part No. 820-3091, Dual atomizer kit - for installing 2 atomizers on V engines or multiple in-line assemblies. Kit contains 2 tubes 48” long and 1 tube tee. Part No. 820-0327, 18 oz. cylinder of ether for Zerostart units - 1” neck size. Part No. 820-1277, 21 oz. stubby cylinder of ether - 1” neck size. Part No. 820-3903, 1” standard gasket for ether injection systems. Part No. 820-0386, Surface mount thermostat for ether injection systems. Part No. 820-2281, 1/2” NPT low temp. thermostat for ether injection systems. Part No. 829-1837, 1/2” NPT standard temp. thermostat for ether injection systems. 820-3091 820-4209 greggdistributors.ca E-Z MOUNT — Standard electrical and mechanical kits are also available. Please consult charts on the following page for your specific application requirements. Q15
© Copyright 2024