1. technology and computing

Technical Information
Micropilot M FMR250
Level-Radar
Smart Transmitter for continuous and non-contact level
measurement in solids.
Cost-effective 4 to 20 mA 2-wire technology.
Application
The Micropilot M performs continuous, non-contact
level measurement especially in powdery to granular
bulk solids. Additionally it can be used in liquids as well.
Dust, filling noises, temperature layers and gas
stratification do not affect measurement.
Typical areas of application are:
• Level measurement in tall silos with extremely dusty
bulk solids e.g. cement, raw meal or animal feed.
• Applications with high temperature requirements up
to 200 °C (392 °F), e.g. clinker or fly ash.
• Applications with highly abrasive bulk solids e.g.
ferrite.
The FMR250 with DN80 or DN100 horn antenna for all
standard applications, particularly also for small nozzle
sizes.
The FMR250 with DN200 parabolic antenna offers high
beam focussing of 4° and is thus ideal for applications
with many installations.
TI390F/24/ae
Your benefits
• 2-wire technology, low price:
2-wire technology reduces wiring costs and allows
easy implementation into existing systems.
• Non-contact measurement:
Measurement is almost independent from product
properties.
• Easy on-site operation via menu-driven alphanumeric
display.
• Easy commissioning, documentation and diagnostics
via Endress+Hauser operating software.
• Integrated air purge connection for extremely dusty
conditions or media tending to create build-up.
• Max. measuring range 70 m (229 ft).
• Suitable for process temperatures up to 200 °C
(392 °F).
• HART® or PROFIBUS® PA respectively
FOUNDATION™ Fieldbus protocol.
• Optional remote display and operation.
Micropilot M FMR250
Table of contents
Function and system design. . . . . . . . . . . . . . . . . . . . . 3
Dielectric constant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Measuring principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Equipment architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Mechanical construction . . . . . . . . . . . . . . . . . . . . . . 24
Measured variable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Measuring range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Measuring conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Operating frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Transmitting power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Design, dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
E+H UNI flange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Process connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Human interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Output signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Signal on alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Linearization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Data of the FOUNDATION Fieldbus interface . . . . . . . . . . . . . . . . 9
Operation concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Local operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Auxiliary energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Cable gland . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Terminal assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Load HART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Cable entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Current consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Ripple HART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Max. noise HART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Overvoltage protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Performance characteristics. . . . . . . . . . . . . . . . . . . . 15
Reference operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Maximum measured error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Reaction time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Influence of ambiente temperature . . . . . . . . . . . . . . . . . . . . . . . 15
Operating conditions: Installation . . . . . . . . . . . . . . . 16
Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Beam angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Installation in vessel FMR250 . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
FMR250 with top target positioner . . . . . . . . . . . . . . . . . . . . . . . 21
Integrated air purge connection . . . . . . . . . . . . . . . . . . . . . . . . . 21
24
26
27
27
27
27
27
28
28
29
30
31
Certificates and approvals . . . . . . . . . . . . . . . . . . . . . 35
CE approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ex approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External standards and guidelines . . . . . . . . . . . . . . . . . . . . . . . .
RF approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35
35
35
35
Ordering information. . . . . . . . . . . . . . . . . . . . . . . . . 36
Micropilot M FMR250 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Weather protection cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote display FHX40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Commubox FXA191 HART . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Commubox FXA195 HART . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Commubox FXA291 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ToF Adapter FXA291 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
39
39
40
40
40
40
Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Operating conditions: Environment. . . . . . . . . . . . . . 22
Ambient temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Climate class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Degree of protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Vibration resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Cleaning of the antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Electromagnetic compatibility (EMC). . . . . . . . . . . . . . . . . . . . . . 22
Operating conditions: Process . . . . . . . . . . . . . . . . . . 23
Process temperature range / Process pressure limits . . . . . . . . . . 23
2
Endress+Hauser
Micropilot M FMR250
Function and system design
Measuring principle
The Micropilot is a "downward-looking" measuring system, operating based on the time-of-flight method. It
measures the distance from the reference point (process connection) to the product surface. Radar impulses are
emitted by an antenna, reflected off the product surface and received again by the radar system.
Flange:
reference point of
measurement
20 mA
100%
Flange:
reference point of
measurement
D
E
F
L
4 mA
0%
Threaded
connection
1-½ BSPT (R 1-½”)
or 1-½” NPT:
reference point of
measurement
L00-FMR250xx-15-00-00-en-001
Input
The reflected radar impulses are received by the antenna and transmitted into the electronics. A microprocessor
evaluates the signal and identifies the level echo caused by the reflection of the radar impulse at the product
surface. The unambiguous signal identification is accomplished by the PulseMaster® software, based on many
years of experience with time-of-flight technology.
The distance D to the product surface is proportional to the time of flight t of the impulse:
D = c · t/2,
with c being the speed of light.
Based on the known empty distance E, the level L is calculated:
L=E–D
Refer to the above figure for the reference point for "E".
The Micropilot is equipped with functions to suppress interference echoes. The user can activate these
functions. They ensure that interference echoes (i.e. from internals and struts) are not interpreted as level echo.
Output
The Micropilot is commissioned by entering an empty distance E (=zero), a full distance F (=span) and an
application parameter. The application parameter automatically adapts the instrument to the process
conditions. The data points “E” and “F” correspond with 4mA and 20mA for instruments with current output.
They correspond with 0 % and 100 % for digital outputs and the display module.
A linearization with max. 32 points, based on a table entered either manually or semi-automatically, can be
activated locally or remotely. This function provides a measurement in engineering units and a linear output
signal for spheres, horizontal cylindrical tanks and vessels with conical outlet.
Endress+Hauser
3
Micropilot M FMR250
Equipment architecture
Stand-alone
The instrument provides a 4 to 20 mA output with HART protocol, or PROFIBUS PA respectively
FOUNDATION Fieldbus communication.
4 to 20 mA output with HART protocol.
The complete measuring system consists of:
PLC
- FieldCare
- ToF Tool - FieldTool
Package
- FieldCare
- ToF Tool - FieldTool
Package
Service adapter
FXA193
Commubox
FXA191/195
Transmitter power
supply unit
RMA422
or RN221N
(communication resistor
included)
Operating and
display module
VU331
ENDRESS + HAUSER
%
–
+
E
dsdmdm
df das.
asdas fa
asas la.
DELTABAR: * * * * * * * *
ONLINE
1 QUICK SETUP
2 OPERATING MENU
3 PV
4 SV
HELP
SAVE
9
ENDRESS + HAUSER
RMA 422
352 mbar
0 °C
Page
Up
Bksp
6
Delete
Page
On
#%&
ABC
1
2
Copy
Paste
GHI
3
MNO
5
6
Insert
PQRS
+ Hot Key
TUV
W XY Z
8
7
FXA191/195
or
DXR375
DEF
Hot Key
JKL
4
9
,()‘
_<>
+*/
.
0
-
375
FIELD COMMUNICATOR
HART handheld
DXR375
L00-FMR2xxxx-14-00-06-en-001
Local operation
• with display and operating module VU331,
• with a Personal Computer, FXA193 and the operating software "ToF Tool - FieldTool Package" respectively
"FieldCare". The ToF Tool is a graphical operating software for instruments from Endress+Hauser that
operate based on the time-of-flight principle (radar, ultrasonic, guided micro-impulse). It assists with
commissioning, securing data, signal analysis and documentation of the measuring point.
Remote operation
• with HART handheld DXR375,
• with a Personal Computer, Commubox FXA191/195 and the operating software "ToF Tool - FieldTool
Package" respectively "FieldCare".
4
Endress+Hauser
Micropilot M FMR250
System integration via PROFIBUS PA
A maximum of 32 transmitters (8 if mounted in an explosion hazardous location EEx ia IIC according to
FISCO-model) can be connected to the bus. The segment coupler provides the operating voltage to the bus.
Both on-site as well as remote operation are possible.The complete measuring system consists of:
Personal computer e.g. with
ToF Tool - FieldTool
Package and
Profibard resp. Proficard
PLC
Segment coupler
PROFIBUS DP
ENDRESS + HAUSER
PROFIBUS PA
T
More
Functions
(valves etc)
Operating and
display module
VU331
Service adapter
· FXA291/ToF Adapter FXA291
· FSA193
ENDRESS + HAUSER
%
–
+
E
Prosonic M
Micropilot M
Levelflex M
ToF Tool - FieldTool Package
L00-FMxxxxxx-14-00-06-en-001
System integration via FOUNDATION Fieldbus
A maximum of 32 transmitters (standard, EEx em or EEx d) can be connected to the bus. For protection class
EEx ia IIC: the max. number of transmitters depends on the established rules and standards for intrinsically
safe circuits (EN 60079-14), proof of intrinsically safety. Both on-site as well as remote operation are possible.
The complete measuring system consists of:
Personal computer
e.g. with
NI-FBUS configurator
power supply
FF link
power conditioner
T
T
Additional
functions
(valves etc.)
Operating and
display module
VU331
Service adapter
• FXA291/ToF Adapter FXA291
• FXA193
ENDRESS + HAUSER
–
%
+
E
Micropilot M
Prosonic M
Levelflex M
ToF Tool FieldTool
Package
FieldCare
L00-FMxxxxxx-14-00-06-en-003
Endress+Hauser
5
Micropilot M FMR250
System integration via Fieldgate
Vendor Managed Inventory
By using Fieldgates to interrogate tank or silo levels remotely, suppliers of raw materials can provide their
regular customers with information about the current supplies at any time and, for example, account for them
in their own production planning. For their part, the Fieldgates monitor the configured level limits and, if
required, automatically activate the next supply. The spectrum of options here ranges from a simple purchasing
requisition via e-mail through to fully automatic order administration by coupling XML data into the planning
systems on both sides.
Remote maintenance of measuring equipment
Fieldgates not only transfer the current measured values, they also alert the responsible standby personnel, if
required, via e-mail or SMS. In the event of an alarm or also when performing routine checks, service
technicians can diagnose and configure connected HART devices remotely. All that is required for this is the
corresponding HART operating software (e.g. ToF Tool - FieldTool Package, FieldCare, ...) for the connected
device. Fieldgate passes on the information transparently, so that all options for the respective operating
software are available remotely. Some on-site service operations can be avoided by using remote diagnosis and
remote configuration and all others can at least be better planned and prepared.
Remote monitoring
Remote confoguration/diagnosis
HTTP script
Web browser
…
Via HART Client:
- ToF Tool - FieldTool
Package
- FieldCare
...
Multidrop-Connector
FXN520
e.g. 2 x RN221N-B …
ENDRESS+HAUSER
RN 221N
Fieldgate
FXA520
Channel 1
Channel 2
Analog
Ethernet
GSM
FXN 520
ENDRESS+HAUSER
RN 221N
Fieldgate
FXA520
20 to 45 VDC
Hazardous Area
Non-hazardous Area
.
L00-FXA520xx-14-00-06-en-009
Note!
The number of instruments which can be connected in mutidrop mode can be calculated by the "FieldNetCalc"
program. A description of this program can be found in Technical Information TI 400F (Multidrop Conncector
FXN520). The program is available form your Endress+Hauser sales organisation or in the internet at:
"www.endress.com Download" (Text Search = "Fieldnetcalc").
6
Endress+Hauser
Micropilot M FMR250
Input
Measured variable
The measured variable is the distance between a reference point (refer to fig. on page 2) and a reflective surface
(i.e. medium surface).
The level is calculated based on the vessel height entered.The level can be converted into other units (volume,
mass) by means of a linearization (32 points).
Measuring range
The usable measuring range depends on the size of the antenna, the reflectivity of the medium, the mounting
location and eventual interference reflections. The maximum configurable range is 70 m (229 ft) for
Micropilot M FMR250.
Reduction of the max. possible measuring range through:
• Media with poor reflection properties (= small DC). For examples refer to table 1.
• Angle of repose.
• Extremely loose surfaces of bulk solids, e.g. bulk solids with low bulk weight for pneumatic filling.
• Build-up, above all of moist products.
Table 1:
The following table describes the media groups and the dielectric constant εr.
Media group
DC (εr)
Examples
A
1.6 to 1.9
– Plastic granulate
– White lime, special cement
– Sugar
19 to 16 dB
B
1.9 to 2.5
– Portland cement, plaster
16 to 13 dB
C
2.5 to 4
– Grain, seeds
– Ground stones
– Sand
13 to 10 dB
D
4 to 7
– Naturally moist (ground) stones, ores
– Salt
10 to 7 dB
E
>7
Signal attenuation
– Metallic powder
– Carbon black
– Coal
< 7 dB
The respective lower group applies for very loose or loosened bulk solids.
Antenna selection
Endress+Hauser
Antenna type
Application
FMR250-*4*... 3" (DN80)
FMR250-*5*... 4" (DN100)
The FMR250 with 3" (DN80) or 4" (DN100) horn antenna for all standard applications,
particularly also for small nozzle sizes.
To achieve an optimised signal strength it is recommended to use an antenna with as
large as possible diameter.
In small tanks in particular, an antenna extension should not be used wherever possible
to optimize dynamics at close range.
FMR250-*6*... 8"(DN200)
The FMR250 with 8" (DN200) parabolic antenna offers high beam focussing of 4° and is
thus ideal for applications with many installations.
7
Micropilot M FMR250
Measuring conditions
• The measuring range begins, where the beam hits the vessel bottom. Particularly with dish bottoms or
conical outlets the level cannot be detected below this point.
The maximum measuring range can be increased in such applications by using a top target positioner
(see Page 16).
• In case of media with a low dielectric constant (groups A and B), the vessel bottom can be visible through
the medium at low levels. In order to guarantee the required accuracy in these cases, it is recommended to
position the zero-point at a distance C = 2" to 6" (50...150 mm) above the vessel bottom (see Fig.).
• In principle it is possible to measure up to the tip of the antenna with FMR250. However, due to
considerations regarding abrasion and build-up, the end of the measuring range should not be chosen any
closer than A=16" (400 mm, see Fig.) to the tip of the antenna.
A
100%
Measuring range
C
0%
L00-FMR250xx-17-00-00-en-001
Operating frequency
• FMR250: K-band
Transmitting power
Average energy density in beam direction:
8
Distance
Average energy density
measuring range = 70 m (229 ft)
3 ft (1 m)
< 64 nW/cm2
16 ft (5 m)
< 2.5 nW/cm2
Endress+Hauser
Micropilot M FMR250
Output
Output signal
• 4 to 20 mA with HART protocol
• PROFIBUS PA
– signal coding: Manchester Bus Powered (MBP); Manchester II
– data transmission rate: 31.25 KBit/s, voltage mode
• FOUNDATION Fieldbus (H1)
– signal coding: Manchester Bus Powered (MBP); Manchester II
– data transmission rate: 31.25 KBit/s, voltage mode
Signal on alarm
Error information can be accessed via the following interfaces:
• Local display:
– Error symbol
– Plain text display
• Current output
• Digital interface
Linearization
The linearization function of the Micropilot M allows the conversion of the measured value into any unit of
length or volume. Linearization tables for calculating the volume in cylindrical vessels are pre-programmed.
Other tables of up to 32 value pairs can be entered manually or semi-automatically.
Data of the FOUNDATION
Fieldbus interface
Basic Data
Device Type
100F (hex)
Device Revision
05 (hex)
DD Revision
01 (hex)
CFF Revision
01 (hex)
ITK Version
5.0
ITK-Certification Driver-No.
IT042000
Link Master (LAS) cabable
yes
Link Master / Basic Device selectable
yes; Default: Basic Device
Number VCRs
24
Number of Link-Objects in VFD
24
Virtual communication references (VCRs)
Permanent Entries
1
Client VCRs
0
Server VCRs
24
Source VCRs
23
Sink VCRs
0
Subscriber VCRs
23
Publisher VCRs
23
Link Settings
Endress+Hauser
Slot time
4
Min. Inter PDU delay
4
Max. response delay
10
9
Micropilot M FMR250
Transducer Blocks
Block
Content
Output values
Sensor Block
contains all parameters related to the mesurement
• level or volume1) (channel 1)
• distance (channel 2)
Diagnsotic Block contains diagnostic information
no output values
Display Block
no output values
1)
contains parameters to configure the local display
depends on sensor block configuration
Function Blocks
Block
Content
Resource Block
The Resource Block contains all the data that uniquely
identifies the field device. It is an electronic version of a
nameplate of the device.
Analog Input
Block 1
Analog Input
Block 2
The AI block takes the manufacturer's input data,
selected by channel number, and makes it available to
other function blocks at its output.
30 ms
standard
PID Block
The PID block serves as proportional-integral-derivative
controller and is used almost universally to do closedloop-control in the field including cascade and feedforward.
80 ms
standard
50 ms
standard
Input Selector
Block
The input selector block provides selection of up to four 30 ms
inputs and generates an output based on the configured
action. This block normally receives its inputs from AI
blocks. The block performs maximum, minimum, middle,
average and ‘first good’ signal selection.
standard
Signal Characterizer Block
The signal characterizer block has two sections, each
40 ms
with an output that is a non-linear function of the respective input. The non-linear function is determined by a single look-up table with 21 arbitrary x-y pairs.
standard
Integrator Block
The Integrator Function Block integrates a variable as a
60 ms
function of the time or accumulates the counts from a
Pulse Input block. The block may be used as a totalizer
that counts up until reset or as a batch totalizer that has a
setpoint, where the integrated or accumulated value is
compared to pre-trip and trip settings, generating discrete
signals when these settings are reached.
standard
Arithmetic Block This block is designed to permit simple use of popular
measurement math functions. The user does not have to
know how to write equations. The math algorithm is
selected by name, chosen by the user for the function to
be done.
10
Execution time
Functionality
enhanced
Endress+Hauser
Micropilot M FMR250
Auxiliary energy
Electrical connection
Terminal compartment
Three housings are available:
• Aluminium housing F12 with additionally sealed terminal compartment for:
– standard,
– Intrinsically safe (EEx ia),
– Dust ignition proof (EEx ia with dust Ex).
• Aluminium housing T12 with separate terminal compartment for:
– standard,
– Explosion proof (EEx d),
– Intrinsically safe (EEx ia), with overvoltage protection,
– Dust ignition proof (dust Ex).
• 316L housing F23 for:
– standard,
– Intrinsically safe (EEx ia),
– Dust ignition proof (EEx ia with dust Ex).
The electronics and current output are galvanically isolated from the antenna circuit.
T12 housing
F12 housing
F23 housing
1 2 3 4
1 2 3 4
1 2 3 4
sealed terminal
compartment
L00-FMR2xxxx-04-00-00-en-019
Cable gland
Terminals
Endress+Hauser
Type
Clamping area
Standard, Intrinsically safe, EEx ia
Plastic M20x1.5
5 to 10 mm
EEx em, EEx nA
Metal M20x1.5
7 to 10.5 mm
All
Metal, threaded
1/2" NPT
For wire cross-sections 16 to 18 AWG (0.5 to 2.5 mm2)
11
Micropilot M FMR250
Terminal assignment
2-wire, 4 to 20 mA with HART
The 2-wire cable is connected to the screw terminals
in the terminal compartment.
Power
Alternatively
Cable specification:
• A standard installation cable is sufficient if only the
analog signal is used. Use a shielded cable when
working with a superimposed communications
signal (HART).
Note!
Protective circuitry against reverse polarity, RFI, and
over-voltage peaks is built into the device (refer to
TI241F »basics for EMC-tests«).
Note!
See TI402F/00/en for connection to Tank Side
Monitor NRF590.
Commubox
FXA 191/195
DXR 375
4 to 20 mA
Test sockets for testing
of the signal current
1 2 3 4
L- L+ I+
Plant
ground
IL00-FMxxxxxx-04-00-00-en-015
PROFIBUS PA
The digital communication signal is transmitted to the
bus via a 2-wire connection. The bus also provides the
auxiliary energy.
For further information on the network structure and
earthing and for further bus system components such
as bus cables, see the relevant documentation, e.g.
Operating Instructions BA034S "Guidelines for
planning and commissioning PROFIBUS DP/PA" and
the PNO Guideline.
Cable specification:
• Use a twisted, shielded two-wire cable, preferably
cable type A
1 2 3 4
–
- ++
Plant
ground
L00-FMxxxxxx-04-00-00-en-022
Note!
For further information on the cable specifications, see Operating Instructions BA034S "Guidelines for planning
and commissioning PROFIBUS DP/PA", PNO Guideline 2.092 "PROFIBUS PA User and Installation Guideline"
and IEC 61158-2 (MBP).
FOUNDATION Fieldbus
The digital communication signal is transmitted to the
bus via a 2-wire connection. The bus also provides
the auxiliary energy.
For further information on the network structure and
earthing and for further bus system components such
as bus cables, see the relevant documentation, e.g.
Operating Instructions BA013S "FOUNDATION
Fieldbus Overview" and the FONDATION Fieldbus
Guideline.
Cable specification:
• Use a twisted, shielded two-wire cable, preferably
cable type A
1 2 3 4
–
- ++
Plant
ground
L00-FMxxxxxx-04-00-00-en-022
Note!
For further information on the cable specifications, see Operating Instructions BA013S "FOUNDATION
Fieldbus Overview", FONDATION Fieldbus Guideline and IEC 61158-2 (MBP).
Load HART
12
Minimum load for HART communication: 250 Ω
Endress+Hauser
Micropilot M FMR250
Supply voltage
HART
The following values are the voltages across the terminals directly at the instrument:
Communication
Terminal voltage
Current
consumption
minimal
maximal
4 mA
16 V
36 V
20 mA
7.5 V
36 V
4 mA
16 V
30 V
20 mA
7.5 V
30 V
HART
standard
Intrinsically Safe
(EEx ia)
Fixed current, adjustable
e.g. for solar power
operation (measured
value transferred at
HART)
Fixed current for HART
Multidrop mode
1)
Explosion proof
(EEx d)
4 mA
16 V
30 V
20 mA
11 V
30 V
Dust explosion
proof (dust Ex)
4 mA
16 V
30 V
20 mA
11 V
30 V
standard
11 mA
10 V
36 V
Intrinsically Safe
(EEx ia)
11 mA
10 V
30 V
standard
4 mA1))
16 V
36 V
Intrinsically Safe
(EEx ia)
4 mA1)
16 V
30 V
Start up current 11 mA.
FOUNDATION Fieldbus
Supply voltage
9 V to 32 V 1)
Lift-off voltage
9V
1)
There may be additional restrictions for devices with an explosion protection certificate. Refer to the notes in the
appropriate safety instructions (XA).
Cable entry
• Cable gland: M20x1.5 (for EEx d: cable entry)
• Cable entry: G ½ or ½" NPT
Power consumption
min. 60 mW, max. 900 mW
Current consumption
HART
3.6 to 22 mA. For HART Multidrop: start up current is 11 mA.
PROFIBUS PA
Max. 13 mA.
FOUNDATION Fieldbus
Endress+Hauser
Basic current
15 mA
In-rush current
≤ 15 mA
Error current
0 mA
FISCO/FNICO compliant
yes
Polarity sensitive
no
13
Micropilot M FMR250
FISCO
Ui
17.5 V
Ii
500 mA; with surge arrester 273 mA
Pi
5.5 W; with surge arrester1, 2 W
Ci
5 nF
Li
0.01 mH
Ripple HART
47 to 125 Hz: Uss = 200 mV (at 500 Ω)
Max. noise HART
500 Hz to 10 kHz: Ueff = 2.2 mV (at 500 Ω)
Overvoltage protector
The level transmitter Micropilot M with T12-housing (housing version "D", see ordering information on page
36-38) is equipped with an internal overvoltage protector (600 V surge arrester). Connect the metallic housing
of the Micropilot M to the vessel wall or shield directly with an electrically conductive lead to ensure reliable
potential matching.
14
Endress+Hauser
Micropilot M FMR250
Performance characteristics
Reference operating
conditions
•
•
•
•
•
Maximum measured error
Typical statements for reference conditions, include linearity, repeatability, and hysteresis:
• up to 3 ft (1 m): ±1.18" (30 mm)
• above 3 ft (1 m): ±0.60" (15 mm), or 0.04% of measuring range, whatever is larger
Resolution
Digital / analog in % 4 to 20 mA
• FMR250: 0.04" (1mm) / 0.03 % of measuring range
Reaction time
The reaction time depends on the parameter settings (min. 1 s). In case of fast level changes, the instrument
needs the reaction time to indicate the new value.
Influence of ambiente
temperature
The measurements are carried out in accordance with EN 61298-3:
• digital output (HART, PROFIBUS PA, FOUNDATION Fieldbus):
– FMR250
average TK: 0.20"/10 K (5 mm/10 K), max. 0.60" (15 mm) over the entire temperature
range -40 to +176°F (-40 to +80°C)
• Current output (additional error, in reference to the span of 16 mA):
– Zero point (4 mA)
average TK: 0.03 %/10 K, max. 0.45 % over the entire temperature range
-40 to +176°F (-40 to +80°C)
– Span (20 mA)
average TK: 0.09 %/10 K, max. 0.95 % over the entire temperature range
-40 to +176°F (-40 to +80°C)
Endress+Hauser
temperature = +20 °C (68 °F) ±5 °C (9 °F)
pressure = 1013 mbar abs. (14.7 psia) ±20 mbar (0.3 psi)
relative humidity (air) = 65 % ±20%
ideal reflector
no major interference reflections inside the signal beam
15
Micropilot M FMR250
Operating conditions: Installation
Installation instructions
Orientation
• Recommended distance (1) wall – outer edge of
nozzle: ~1/6 of vessel diameter. However, the
device should not, under any circumstances, be
mounted less than 20 cm (8") from the vessel wall.
Note!
If the tank wall is not smooth (corrugated metal,
welding seams, irregularities etc.) the distance from
the wall should be kept as large as possible. If
necessary, use a top target positioner to prevent
interference reflections from the tank wall.
• Not in the centre (3), interference can cause signal
loss.
• Not above the fill stream (4).
• It is recommended to use a weather protection
cover (2) in order to protect the transmitter from
direct sun or rain. Assembly and disassembly is
simply done by means of a tension clamp (see
Accessorieson page 39).
• In extremely dusty applications, the integrated air
purge connection can prevent clogging of the
antenna.
2
3
4
1
L00-FMR250xx-17-00-00-xx-003
Vessel installations
• Avoid any installations (1), like limit switches,
struts, etc., inside the signal beam (see Beam angle
on Page 17).
• Symmetrical installations (2), i.e. reinforcing rings,
heating coils, etc., can also interfere with the
measurement.
Optimization options
• Antenna size: the bigger the antenna, the smaller
the beam angle, the less interference echoes.
• Mapping: the measurement can be optimized by
means of electronic suppression of interference
echoes.
• Antenna alignment: refer to "Optimum mounting
position"
• In devices with top target positioner, the sensor can
be optimally aimed within the vessel, and/or
interference reflections can be avoided.
The max. angle β is ±15°.
• In particular, sensor alignment serves to:
– prevent interference reflections
– extend the maximum possible measuring range
in conical outlets.
• Metallic screens (3) mounted at a slope spread the
radar signals and can, therefore, reduce
interference echoes.
1
3
2
Please contact Endress+Hauser for further
information.
L00-FMR250xx-17-00-00-xx-002
16
Endress+Hauser
Micropilot M FMR250
Measurement in a plastic tank
If the outer wall of the tank is made of a non-conductive material (e.g. GRP), microwaves can also be reflected
off interfering installations outside the signal beam (e.g. metallic pipes (1), ladders (2), grates (3), …). Therefore,
avoid such interfering installations in the signal beam.
auser
Endress+H
ENDRESS+HAUS
MICROPILOT
ER
II
VH
00
max. 20
U 16...36
4...20 mAV DC
IP 65
m
TA >70°C
: t >85°C
Made in Germany
Messbereich
Measuring
range
Maulburg
Order Code:
Ser.-No.:
- +
V
H
auser
Endress+H
ENDRESS+HAUS
MICROPILOT
ER
II
VH
00
Order Code:
max. 20
U 16...36
4...20 mAV DC
IP 65
m
TA >70°C
TA >70°C
V
H
VH
00
Maulburg
IP 65
m
: t >85°C
Made in Germany
max. 20
U 16...36
4...20 mAV DC
- +
auser
Endress+H
ENDRESS+HAUS
MICROPILOT
ER
II
Order Code:
Ser.-No.:
Messbereich
Measuring
range
: t >85°C
Made in Germany
Messbereich
Measuring
range
Maulburg
Ser.-No.:
- +
V
H
2
3
1
L00-FMR250xx-17-00-00-xx-014
Please contact Endress+Hauser for further information.
Beam angle
The beam angle is defined as the angle a where the energy density of the radar waves reaches half the value of
the maximum energy density (3dB-width). Microwaves are also emitted outside the signal beam and can be
reflected off interfering installations. Beam diameter W as function of antenna type (beam angle α) and
measuring distance D:
Parabolic antenna
80 mm / 3"
100 mm / 4"
200 mm / 8"
Beam angle α
10°
8°
4°
Measuring
distance (D)
Endress+Hauser
Horn antenna
Antenna size
FMR250
Beamwidth diameter (W)
D
80 mm / 3"
100 mm / 4"
200 mm / 8"
5 m / 16 ft
0.87 m / 2.80 ft
0.70 m / 2.24 ft
0.35 m / 1.12 ft
10 m / 32 ft
1.75 m / 5.60 ft
1.40 m / 4.48 ft
0.70 m / 2.23 ft
15 m / 49 ft
2.62 m / 8.57 ft
2.10 m / 6.85 ft
1.05 m / 3.42 ft
20 m / 65 ft
3.50 m / 11.37 ft
2.80 m / 9.09 ft
1.40 m / 4.54 ft
30 m / 98 ft
5.25 m / 17.15 ft 4.20 m / 13.71 ft
2.10 m / 6.84 ft
40 m / 131 ft
7.00 m / 22.92 ft 5.59 m / 18.32 ft
2.79 m / 9.15 ft
50 m / 164 ft
8.75 m / 28.70 ft 6.99 m / 22.94 ft
3.50 m / 11.45 ft
W
W = 2 . D . tan _
2
L00-FMR2xxxx-14-00-06-de-027
17
Micropilot M FMR250
Installation in vessel FMR250
Optimum mounting position
90
°
Marker at instrument
flange or threaded boss 1)
90°
°
90
1-½” NPT or
1-½” BSPT (R 1-½”)
90
°
ANIS 3” to 8”
(DN 80 to 200)
90
°
1)
at version with top target positioner, the marker is at the housing adapter
(opposite the air purge connection)
L00-FMR250xx-17-00-00-en-009
Standard installation FMR250 with horn
antenna
• Observe installation instructions on Page 16.
• Marker is aligned towards vessel wall.
• The marker is always exactly in the middle
between two bolt-holes in the flange.
• After mounting, the housing can be turned 350° in
order to simplify access to the display and the
terminal compartment.
• The horn antenna should protrude from the nozzle.
If this is not possible for mechanical reasons, larger
nozzle heights can be accepted.
Note!
Please contact Endress+Hauser for application with
higher nozzle.
• Vertical horn antenna.
Ideally, the horn antenna should be installed
vertically.
To avoid interference reflections or for optimum
alignment within the vessel, the FMR250 with
optional top target positioner can be swiveled by
15° in all directions.
H
ØD
L00-FMR250xx-17-00-00-en-004
1)
18
Antenna size
80 mm / 3"
100 mm / 4"
D [mm / inch]
75 / 3
95 / 3.7
H [mm / inch]
(without antenna extension)
< 260 / < 10.2
< 330 / < 12.9
1))
from 28.11.2005: H < 480 mm / 18.8 inch
Endress+Hauser
Micropilot M FMR250
Standard installation FMR250 with parabolic
antenna
• Observe installation instructions on Page 16.
• Marker is aligned towards vessel wall.
• The marker is always exactly in the middle
between two bolt-holes in the flange.
• After mounting, the housing can be turned 350° in
order to simplify access to the display and the
terminal compartment.
• Ideally the parabolic antenna should protrude from
the nozzle (1).
Particularly when using the top target positioner,
please ensure that the parabolic reflector is
protruding from the nozzle/roof so as not to inhibit
alignment.
Note!
For application with higher nozzle install parabolic
antenna completely in the nozzle (2), including
RF-wave guide (3).
• Vertical parabolic antenna.
Ideally, the parabolic antenna should be installed
vertically.
To avoid interference reflections or for optimum
alignment within the vessel, the FMR250 with
optional top target positioner can be swiveled by
15° in all directions.
1
H
ØD
2
3
L00-FMR250xx-17-00-00-en-005
Endress+Hauser
Antenna size
200 mm / 8"
D [mm / inch]
197 / 7.75
H [mm / inch]
(without antenna extension)
< 50 / < 1.96
19
Micropilot M FMR250
Examples for installation with small flange (< parabolic reflector)
Standard installation
Nozzle
D
Antenna size
D inches (mm)
H inches (mm) 1)
H
For installation
in nozzle, you
can dismantle
the parabolic reflector
8” (200 mm)
7.76 (197)
< 1.97 (50)
1) without antenna extension
4 bolts
Caution!
When installing on hinged flanges, the length of the antenna
must be taken into account. Ensure the nozzle/opening is
wide enough to accommodate the antenna tip.
L00-FMR250xx-17-00-00-en-007
20
Endress+Hauser
Micropilot M FMR250
FMR250 with top target
positioner
Optimum mounting position
Using the top target positioner it is possible to tilt the antenna axis by up to 15° in all directions. The top target
positioner is used for the optimum alignment of the radar beam with the bulk solids surface.
±15°
±15°
L00-FMR250xx-17-00-00-de-008
Align antenna axis:
Integrated air purge
connection
1.
Loosen screws.
2.
Align antenna axis (here this is possible up to max. ±15° in all directions).
3.
Tighten screws.
In extremely dusty applications, the integrated air
purge connection can prevent clogging of the
antenna. Pulsed operation is recommended.
• Pulsed operation:
max. pressure of purge air: 87 psi (6 bar abs.)
• Permanent operation:
recommended pressure range of the purge air: 2.9
to 7.3 psi (200 to 500 mbar).
Caution!
Make sure to use dry purge air.
Air purge connection:
NPT ¼”
or
G ¼ (max. torque
2.6 lbf ft / 3.5 Nm)
L00-FMR250xx-17-00-00-en-010
Endress+Hauser
21
Micropilot M FMR250
Operating conditions: Environment
Ambient temperature range
Ambient temperature for the transmitter: -40 to +80°C (-40 to +176°F), -50°C (-58°F) on request.
The functionality of the LCD display may be limited for temperatures Ta<4°F (-20°C) and Ta>+140°F (+60°C).
A weather protection cover should be used for outdoor operation if the instrument is exposed to direct sunlight.
Storage temperature
-40 to +80°C (-40 to +176°F), -50°C (-58°F) on request.
Climate class
DIN EN 60068-2-38 (test Z/AD)
Degree of protection
• housing: IP 65, NEMA 4X (open housing and pulled out display: IP20, NEMA 1)
• antenna: IP 68 (NEMA 6P)
Vibration resistance
DIN EN 60068-2-64 / IEC 68-2-64: 20 to 2000 Hz, 1 (m/s2)2/Hz
Cleaning of the antenna
The antenna can get contaminated, depending on the application. The emission and reception of microwaves
can eventually be hindered. The degree of contamination leading to an error depends on the medium and the
reflectivity, mainly determined by the dielectric constant εr. If the medium tends to cause contamination and
deposits, cleaning on a regular basis is recommended. Care has to be taken not to damage the antenna in the
process of a mechanical or hose-down cleaning (eventually air purge connection). The material compatibility
has to be considered if cleaning agents are used!
The maximum permitted temperature at the flange should not be exceeded.
Electromagnetic compatibility
(EMC)
• Electromagnetic compatibility to EN 61326 and NAMUR recommendation EMC (NE 21). For details refer
to the declaration of conformity.
• A standard installation cable is sufficient if only the analogue signal is used. Use a screened cable when
working with a superimposed communications signal (HART).
22
Endress+Hauser
Micropilot M FMR250
Operating conditions: Process
Process temperature range /
Process pressure limits
Note!
The specified rage may be reduced by the selected process connection. The pressure rating (PN) specified on
the nameplate refers to a reference temperature of 20°C, for ASME flanges to 100°F. Observe pressuretemperature dependency.
The pressure values permitted at higher temperatures can be found in the following standards:
• EN 1092-1: 2001 Tab. 18
With regard to its stability property, the material 1.4435 is identical to 1.4404 which is grouped under 13EO
in EN 1092-1 Tab. 18. The chemical composition of the two materials can be identical.
• ASME B 16.5a - 1998 Tab. 2-2.2 F316
• ASME B 16.5a - 1998 Tab. 2.3.8 N10276
• JIS B 2220
Type of antenna Seal
FMR250
E
Standard
Temperature
FKM Viton GLT -40 to +200 °C
(-40 to +392°F)
Pressure
Wetted parts
1)
-1 to 16 bar
(-14.5 to 232 psi 1)
PEEK, seal,
316L SS/1.4404/1.4435
↑
Ordering information see Page 36
1)
E+H UNI flange: -1 to 1 bar (-14.5 to 14.5 psi)
Optional top target positioner: ±15°, seal: FMK Viton GLT
Dielectric constant
Endress+Hauser
• In free space: εr ≥ 1.6 (for horizontal, even product surfaces: εr ≥ 1.4)
23
Micropilot M FMR250
Mechanical construction
Design, dimensions
Housing dimensions
Dimensions for process connection and type of antenna see Page 25.
2.56”
(65)
max. 4.33”
(110)
3.07”
(78)
Ø 5.08”
(129)
ENDRESS+HAUSER
5.91”
(150)
F12 housing
(Aluminum)
3.35”
(85)
L00-F12xxxx-06-00-00-en-001
max. 4.33”
(110)
3.70”
(94)
2.56”
(65)
3.07”
(78)
Ø 5.08”
(129)
ENDRESS+HAUSER
5.91”
(150)
T12 housing
(Aluminum)
3.35”
(85)
L00-T12xxxx-06-00-00-en-001
max. 3.70”
(94)
1.57”
(40)
4.09”
(104)
Ø 5.08”
(129) 5.91”
(150)
F23 housing
(316L SS)
L00-F23xxxx-06-00-00-en-001
24
Endress+Hauser
Micropilot M FMR250
Micropilot M FMR250 - process connection, type of antenna
Housing dimensions see Page 24.
F12 / T12 / F23 housing
Threaded connection
1-½” NPT or
1 ½” BSPT (R 1 ½”)
Flange, 3” or 4”
(DN 80 to 100)
or equivalent
Ø 2.36”
(60)
Ø 2.36”
(60)
Ø 2.36”
(60)
Ø 2.36”
(60)
5.31”
(135)
5.31”
(135)
1.69”
(43)
Alignment unit with
E+H UNI flange, 4” / 8”
( DN 100/200)
E+H UNI flange
8” (DN 200)
5.31”
(135)
0.31”
(8)
5.31”
(135)
0.31”
(8)
1.57”
(40)
b
Ø 8.86” (4” / DN100)
Ø 13.4” (8” / Dn200)
Ø 13.4”
(340)
ØD
0.91”
(23)
Horn antenna
1.97”
(50)
Parabolic antenna
1.97”
(50)
1.06”
(27)
1.06”
(27)
9.84”/17.7”
(250/450)
9.84”/17.7”
(250/450)
L
L
1.97”
(50)
1.57”
(40)
1.97”
(50)
2.95”
(75)
Ød
L
L
Ød
2.95”
(75)
Ød
Ød
Horn antenna
Flange to ANSI B16.5
3” (80 mm) 4” (100 mm)
Antenna size
L in (mm)
8.31 (211) 11.1 (282) 1)
3.74 (95)
d in (mm)
2.95 (75)
1) 16.9” (430 mm) as of November 28, 2005
Flange
b
3”
0.94”
4”
0.94”
D
7.50”
9.0”
Parabolic antenna
Antenna size
L in (mm)
d in (mm)
8” (200 mm)
7.68 (195)
7.76 (197)
for Class 150
NOTE: Other process connections (DIN, JIS) are available,
please contact Endress+Hauser.
L00-FMR250xx-06-00-00-en-005
Endress+Hauser
25
Micropilot M FMR250
E+H UNI flange
Installation hints
The number of bolts has sometimes been reduced. The bolt-holes have been enlarged for adaption of
dimensions, therefore, the flange needs to be properly aligned to the counterflange before the bolts are
tightened. Dimensions are in inches (mm).
A-A
90
4x
4x90°
6x
60
°
°
E+H UNI flange 4” (DN100)
compatible with
- ANSI 4” Class 150
- DN100 PN10/16
- JIS 10K 100A
E+H UNI flange 8” (DN200)
compatible with
- ANSI 8” Class 150
- DN200 PN10/16
- JIS 10K 200A
0.31”
(80)
M80x1.5
Ø 0.75”
(19)
Ø 1.02”
(26)
Ø 1.02”
(26)
4x
90
°
Ø 0.91”
(23)
A
A
A
A
11.6”
(294.5)
6.89”
(175)
13.4”
(340)
7.30”
(185.5)
8.86”
(225)
Material: 316L
L00-FMR250xx-06-00-00-en-006
Top target positioner with E+H UNI flange
A-A
Clamping screw
3 x M8 shifted at 120°
Ø 3.35”
(85)
A
A
1.57”
(40)
0.31”
(8)
Viton seal
E+H UNI flange
4”/8” (DN100/DN200)
±15°
L00-FMR250xx-06-00-00-en-007
26
Endress+Hauser
Micropilot M FMR250
Weight
Micropilot M
FMR250
Weight for F12 or
T12 housing
Approx. 13 lb (6 kg)
+
weight of flange
Weight for F23
housing
Approx. 21 lb (9.4 kg)
+
weight of flange
Material
• Housing:
– housing F12/T12: aluminum (AlSi10Mg), seawater-resistant, powder-coated
– housing F23: 316L SS, corrosion-resistant steel
• Sight window: glass
Process connection
See "Ordering information" on Page 36-38.
Seal
See "Ordering information" on Page 36-38.
Antenna
See "Ordering information" on Page 36-38.
Endress+Hauser
27
Micropilot M FMR250
Human interface
Operation concept
The display of the process value and the configuration of the Micropilot occur locally by means of a large 4-line
alphanumeric display with plain text information. The guided menu system with integrated help texts ensures
a quick and safe commissioning.
To access the display the cover of the electronic compartment may be removed even in hazardous area (IS and
XP).
Remote commissioning, including documentation of the measuring point and in-depth analysis functions, is
supported via the ToF Tool, the graphical operating software for E+H time-of-flight systems.
Display elements
Liquid crystal display (LCD):
Four lines with 20 characters each. Display contrast adjustable through key combination.
LCD
(liquid crystal display)
ENDR
Order MICR ESS+
OPIL HAUS
Ser.-NoCode:
OT
.:
ER
II
IP
T
Maulburg
range
U 16...36
max.
4...20
20
m
mAV DC
65
A >70°C
: t
>85°C
Made in Germany
Messbe
Measur reich
ing
Symbols
ENDRESS + HAUSER
–
+
E
3 keys
Snap-fit
L00-FMxxxxxx-07-00-00-en-001
The VU331 LCD display can be removed to ease operation by simply pressing the snap-fit (see graphic above).
It is connected to the device by means of a 20" (500 mm) cable.
The following table describes the symbols that appear on the liquid crystal display:
Sybmol
Meaning
ALARM_SYMBOL
This alarm symbol appears when the instrument is in an alarm state. If the symbol flashes, this indicates a
warning.
LOCK_SYMBOL
This lock symbol appears when the instrument is locked,i.e. if no input is possible.
COM_SYMBOL
This communication symbol appears when a data transmission via e.g. HART, PROFIBUS PA or
FOUNDATION Fieldbus is in progress.
SIMULATION_SWITCH_ENABLE
This communication symbol appears when simulation in FOUNDATION Fieldbus is enabled via the DIP
switch.
28
Endress+Hauser
Micropilot M FMR250
Operating elements
The operating elements are located inside the housing and are accessible for operation by opening the lid of the
housing.
Function of the keys
Key(s)
Meaning
O or V
Navigate upwards in the selection list
Edit numeric value within a function
S or W
Navigate downwards in the selection list
Edit numeric value within a function
X or Z
F
O and F
or
S and F
O and S and F
Endress+Hauser
Navigate to the left within a function group
Navigate to the right within a function group, confirmation.
Contrast settings of the LCD
Hardware lock / unlock
After a hardware lock, an operation of the instrument via display or
communication is not possible!
The hardware can only be unlocked via the display. An unlock parameter must
be entered to do so.
29
Micropilot M FMR250
Local operation
Operation with VU331
The LC-Display VU331 allows configuration via 3 keys directly at the instrument. All device functions can be
set through a menu system. The menu consists of function groups and functions. Within a function, application
parameters can be read or adjusted. The user is guided through a complete configuration procedure.
Headline
Position indicator
ENDRESS + HAUSER
Symbol
–
+
Main value
Bargraph
Unit
E
Selection list
Function groups -> Functions
HOME
X
F
X
FG00
FG01
FG02
FG03
FG04
FG05
FG06
FG07
...
O
S
F
F
...
F000 F001 F002 F003 F004
F
O
S
X
X
Help text
Envelope
curve
L00-FMRxxxxx-07-00-00-en-002
Operation with handheld unit Field Communicator DXR375
All device functions can be adjusted via a menu operation with the handheld unit DXR375.
dsdmdm
df das.
asdas fa
asas la.
dsdmdm
df das.
asdas fa
asas la.
FMR231: LIC0001
ONLINE
1 GROUP SELECT
2 PV
HELP
8.7 m
FMR231: LIC0001
ONLINE
1 GROUP SELECTION
2 PV
Delete
8.7 m
SAVE
H
HELP
Bksp
Delete
Page
On
#%&
ABC
Bksp
2
3
Paste
Hot Key
GHI
JKL
MNO
PQRS
1
2
3
4
5
BASIC SETUP
SAFETY SETTINGS
LINEARISATION
EXTENDED CALIB.
OUTPUT
Delete
DEF
1
Copy
4
dsdmdm
df das.
asdas fa
asas la.
FMR231: LIC0001
GROUP SELECTION
SAVE
Page
Up
5
6
Insert
+ Hot Key
TUV
WXYZ
7
8
9
,()‘
_<>
+*/
.
0
-
H
SAVE
HOME
Bksp
FMR231: LIC0001
BASIC SETUP
1
2
3
4
5
MEASURED VALUE
TANK SHAPE
MEDIUM PROPERTY
PROCESS COND.
EMPTY CALIBR.
dsdmdm
df das.
asdas fa
asas la.
Page
Up
Page
On
375
FIELD COMMUNICATOR
SAVE
HOME
L00-FMR2xxxx-07-00-00-yy-007
Note!
Further information on the handheld unit is given in the respective operating manual included in the transport
bag of the DXR375.
30
Endress+Hauser
Micropilot M FMR250
Remote operation
The Micropilot M can be remotely operated via HART, PROFIBUS PA and FOUNDATION Fieldbus. Local
adjustments are also possible.
ToF Tool – Fieldtool Package
The ToF Tool is a graphic and menu-guided operating program for measuring devices from
Endress+Hauser. It is used for the commissioning, data storage, signal analysis and documentation of the
devices. The following operating systems are supported: WinNT4.0, Win2000 and Windows XP. You can set
all parameters via the ToF Tool.
The ToF Tool supports the following functions:
• Configuration of transmitters in online operation
• Singal analysis via envelope curve
• Tank linearisation
• Loading and saving device data (upload/download)
• Documentation of the measuring point
Connection options:
• HART via Commubox FXA191 and the RS 232 C serial interface of a computer
• HART via Commubox FXA195 and the USB port on a computer
• PROFIBUS PA via segment coupler and PROFIBUS interface card
• FOUNDATION Fieldbus, PROFIBUS PA and HART via the FXA193/FXA291 service interface
Note!
You can use the ToF Tool to configure the Endress+Hauser parameters for devices with "FOUNDATION
Fieldbus signal". You need an FF configuration program to be able to configure all the FF-specific parameters
and to integrate the device into an FF network.
FieldCare
FieldCare is an Endress+Hauser asset management tool based on FDT technology. With FieldCare, you can
configure all Endress+Hauser devices as well as devices from other manufacturers that support the FDT
standard. The following operating systems are supported: WinNT4.0, Win2000 and Windows XP.
FieldCare supports the following functions:
• Configuration of transmitters in online operation
• Signal analysis via envelope curve
• Tank linearization
• Loading and saving device data (upload/download)
• Documentation of the measuring point
Connection options:
• HART via Commubox FXA191 and the RS 232 C serial interface of a computer
• HART via Commubox FXA195 and the USB port on a computer
• PROFIBUS PA via segment coupler and PROFIBUS interface card
Endress+Hauser
31
Micropilot M FMR250
Menu-guided commissioning
MicropilotM-en-415
Signal analysis via envelope curve
MicropilotM-en-416
32
Endress+Hauser
Micropilot M FMR250
Tank linearization
MicropilotM-en-417
Endress+Hauser
33
Micropilot M FMR250
Operation with NI-FBUS configurator (only FOUNDATION Fieldbus)
The NI-FBUS Configurator is an easy-to-use graphical environment for creating linkages, loops, and a schedule
based on the fieldbus concepts.
You can use the NI-FBUS Configurator to configure a fieldbus network as follows:
• Set block and device tags
• Set device addresses
• Create and edit function block control strategies (function block applications)
• Configure vendor-defined function and transducer blocks
• Create and edit schedules
• Read and write to function block control strategies (function block applications)
• Invoke Device Description (DD) methods
• Display DD menus
• Download a configuration
• Verify a configuration and compare it to a saved configuration
• Monitor a downloaded configuration
• Replace devices
• Log project download changes
• Save and print a configuration
L00-fmxxxxxx-20-00-00-en-001
34
Endress+Hauser
Micropilot M FMR250
Certificates and approvals
CE approval
The measuring system meets the legal requirements of the EC-guidelines. Endress+Hauser confirms the
instrument passing the required tests by attaching the CE-mark.
Ex approval
See "Ordering information" on Page 36-38.
External standards and
guidelines
EN 60529
Protection class of housing (IP-code)
EN 61010
Safety regulations for electrical devices for measurement, control, regulation and laboratory use.
EN 61326-X
EMC product family standard for electrical equipment for measurement, control and laboratory use.
NAMUR
User association for automation technology in process industries.
RF approvals
Endress+Hauser
R&TTE, FCC
35
Micropilot M FMR250
Ordering information
Micropilot M FMR250
Instrument selection
Non-hazardous
area
Certificate
XP
dust Ex
IS
Type of antenna/
Seal
E FKM Viton GLT
Communication
HART
PA
E FKM Viton GLT
FF
HART
PA
E FKM Viton GLT
FF
HART
PA
FF
Housing
F12
F23
T12
F12
F23
T12
T12
L00-FMR250xx-16-00-00-en-001
36
Endress+Hauser
Micropilot M FMR250
Ordering structure Micropilot M FMR250
10
Approval:
A
1
4
G
B
C
D
E
I
J
Q
L
S
T
N
U
V
Y
20
Non-hazardous area
ATEX II 1/2G EEx ia IIC T6
ATEX II 1/2G EEx d [ia] IIC T6
ATEX II 3G EEx nA II T6
ATEX II 1/2GD EEx ia IIC T6, Alu blind cover
ATEX II 1/2G EEx ia IIC T6, ATEX II 1/3D
ATEX II 1/2D, Alu blind cover
ATEX II 1/3D
NEPSI Ex ia IIC T6
NEPSI Ex d(ia)ia IIC T6
NEPSI DIP
TISS EEx d (ia) IIC T3
FM IS-Cl.I/II/III Div.1 Gr.A-G
FM XP-Cl.I/II/III Div.1 Gr.A-G
CSA General Purpose
CSA IS-Cl.I/II/III Div.1 Gr.A-G
CSA XP-Cl.I/II/III Div.1 Gr.A-G
Special version
Antenna:
4
5
6
9
30
Horn 80mm/3"
Horn 100mm/4"
Parabolic 200mm/8"
Special version
Antenna seal; Temperature:
E
Y
FKM Viton GLT; -40 to 200°C/-40 to 392 °F
Special version
40
Antenna extension:
1
2
3
9
50
Not selected
250mm/10"
450mm/18"
Special version
Process connection:
GGJ
GNJ
Thread EN10226 R1-1/2, 316L
Thread ANSI NPT 1-1/2", 316L
X3J
UNI flange DN200/8"/200A, 316L
max PN1/14.5lbs/1K, compatible DN200 PN10/16, 8" 150lbs, 10K 200A
Top target pos., UNI DN100/4"/100A, 316L
max PN1/14.5lbs/1K, compatible DN100 PN10/16, 4" 150lbs, 10K 100A
Top target pos., UNI DN200/8"/200A, 316L
max PN1/14.5lbs/1K, compatible DN200 PN10/16, 8" 150lbs, 10K 200A
XCJ
XEJ
FMR250-
Endress+Hauser
CMJ
CQJ
DN80 PN10/16 B1, 316L flange EN1092-1 (DIN2527 C)
DN100 PN10/16 B1, 316L flange EN1092-1 (DIN2527 C)
ALJ
APJ
3" 150lbs RF, 316/316L flange ANSI B16.5
4" 150lbs RF, 316/316L flange ANSI B16.5
KLJ
KPJ
YY9
10K 80A RF, 316L flange JIS B2220
10K 100A RF, 316L flange JIS B2220
Special version
Product designation (part 1)
37
Micropilot M FMR250
Ordering structure Micropilot M FMR250 (continued)
60
Output; Operation:
A
B
K
C
D
L
E
F
M
Y
70
4-20mA HART; 4-line display VU331, envelope curve display on site
4-20mA HART; w/o display, via communication
4-20mA HART; prepared for FHX40, remote display (Accessory)
PROFIBUS PA; 4-line display VU331, envelope curve display on site
PROFIBUS PA; w/o display, via communication
PROFIBUS PA; prepared for FHX40, remote display (Accessory)
FOUNDATION Fieldbus; 4-line display VU331, envelope curve display on site
FOUNDATION Fieldbus; w/o display, via communication
FOUNDATION Fieldbus; prepared for FHX40, remote display (Accessory)
Special version
Housing:
A
B
C
D
Y
80
F12 Alu, coated IP65 NEMA4X
F23 316L IP65 NEMA4X
T12 Alu, coated IP65 NEMA4X, separate connection compartment
T12 Alu, coated IP65 NEMA4X + OVP, separate connection compartment,
OVP = overvoltage protection
Special version
Cable entry:
2
3
4
9
90
Gland M20x1.5 (EEx d > thread M20)
Thread G1/2
Thread NPT 1/2"
Special version
Additional option:
K Air purge connection G1/4
M Air purge connection NPT 1/4"
Y Special version
FMR250-
38
Complete product designation
Endress+Hauser
Micropilot M FMR250
Accessories
Weather protection cover
A Weather protection cover made of stainless steel is recommended for outdoor mounting (order code:
543199-0001). The shipment includes the protective cover and tension clamp.
F12 / F23 / T12 housing
EN
D
M RE
Orde
ICR SS
r
OP +HA
Se Code
r.-N
ILO US
o.: :
T II
Maulburg
ER
IP
T
65
A >7
0°C
: t
>8
5°C
Made in Germany
Me
Messberei
asuri ch
ng
ran
ge
U 16
ma
x. 20
4...20...36
m
mAV DC
L00-FMR2xxxx-00-00-06-en-001
Remote display FHX40
Wall-mounting
(without mounting bracket)
5.91”
(150)
Pipe-mounting
(mounting bracket and plate
supplied optionally,
see product structure)
7.09”
(180)
4.80”
(122)
Micropilot M
Levelflex M
Prosonic M
0.33”
(8.5)
Separate housing
FHX 40, NEMA 4
(IP 65)
6.30”
(160)
3.15”
(80)
EN
DR
ES
S+
HA
US
ER
Ord
er
Co
Se
r.-N de:
o.:
A >70
°C
°C
3.46”
(88)
Cable
4.72”
(120)
65
: t
>85
Made in Germany
IP
T
Maulburg
Me
Messbere
asu ich
ring
ran
ge
U 16.
ma
x. 20
4... ..36
20
m
mAV DC
4.65”
(118)
3.23”
(82)
0.25”
(6.3)
3.78”
(96)
max. 3.15”
(80)
min. 1.18”
(30)
4.17”
(106)
4.80”
(122)
pipe
L00-FMxxxxxx-00-00-06-en-003
Technical data (cable and housing) and product structure:
Endress+Hauser
Max. cable length
20 m (65 ft)
Temperature range
-30 to +70 °C (-22 to 158 °F)
Degree of protection
IP65 acc. to EN 60529 (NEMA 4)
Materials
Housing: AlSi12; cable glands: nickle plated brass
Dimensions [mm] / [inch]
122 x 150 x 80 (HxWxD) / 4.8 x 5.9 x 3.2
39
Micropilot M FMR250
Approval:
A
1
S
U
N
K
Nn-hazardous area
ATEX II 2 G EEx ia IIC T6, ATEX II 3D
FM IS Cl.I Div.1 Gr.A-D
CSA IS Cl.I Div.1 Gr.A-D
CSA General Purpose
TIIS ia IIC T6 (in preparation)
Cable:
1
5
20m/65ft; for HART
20m/65ft; for PROFIBUS PA/FOUNDATION Fieldbus
Additional option:
A
B
FHX40 -
Basic version
Mounting bracket, pipe 1"/ 2"
Complete product designation
For connection of the remote display FHX40 use the cable which fits the communication version of the
respective instrument.
Commubox FXA191 HART
For intrinsically safe communication with ToF Tool/FieldCare via the RS232C interface. For details refer to
TI237F/00/en.
Commubox FXA195 HART
For intrinsically safe communication with ToF Tool/FieldCare via the USB interface. For details refer to
TI404F/00/en.
Commubox FXA291
The Commubox FXA291 connects Endress+Hauser field instruments with CDI interface (= Endress+Hauser
Common Data Interface) to the USB interface of a personal computer or a notebook. For details refer to
TI405C/07/en.
Note!
For the following Endress+Hauser instruments you need the "ToF Adapter FXA291" as an additional accessory:
•
•
•
•
•
•
•
•
•
•
•
ToF Adapter FXA291
Cerabar S PMC71, PMP7x
Deltabar S PMD7x, FMD7x
Deltapilot S FMB70
Gammapilot M FMG60
Levelflex M FMP4x
Micropilot FMR130/FMR131
Micropilot M FMR2xx
Micropilot S FMR53x, FMR540
Prosonic FMU860/861/862
Prosonic M FMU4x
Tank Side Monitor NRF590 (with additional adapter cable)
The ToF Adapter FXA291 connects the Commubox FXA291 via the USB interface of a personal computer or
a notebook to the following Endress+Hauser instruments:
•
•
•
•
•
•
•
•
•
•
•
Cerabar S PMC71, PMP7x
Deltabar S PMD7x, FMD7x
Deltapilot S FMB70
Gammapilot M FMG60
Levelflex M FMP4x
Micropilot FMR130/FMR131
Micropilot M FMR2xx
Micropilot S FMR53x, FMR540
Prosonic FMU860/861/862
Prosonic M FMU4x
Tank Side Monitor NRF590 (with additional adapter cable)
For details refer to KA271F/00/a2.
40
Endress+Hauser
Micropilot M FMR250
Documentation
Technical Information
Fieldgate FXA320, FXA520
Technical Information for Fieldgate FXA320/520, TI369F/00/en.
Operating Instructions
Micropilot M
Correlation of operating instructions to the instrument:
Endress+Hauser
Instrument Output
Communication
Operating
Instructions
Description of
Instrument
Functions
Brief Operating
Instructions
(in the
Instrument)
FMR250
A, B, K
HART
BA284F/00/en
BA291F/00/en
KA235F/00/a2
C, D, L
PROFIBUS PA
BA331F/00/de
BA291F/00/de
KA235F/00/a2
E, F, M
FOUNDATION Fieldbus
BA336F/00/de
BA291F/00/de
KA235F/00/a2
41
Micropilot M FMR250
Certificates
Correlation of safety instructions (XA) and certificates (ZE) to the instrument:
Instrument Certificate Explosion protection
Output
Communication
FMR250
PTB 04 ATEX
XA
—
—
—
A
Non-hazardous area
A, B, C,
D, K, L
E, F, M
HART,
PROFIBUS PA
FOUNDATION Fieldbus
1
ATEX II 1/2G EEx ia IIC T6
A, B, K
HART
A, B, D
2108
XA313F
C, D, L
E, F, M
PROFIBUS PA
FOUNDATION Fieldbus
A, B, D
2108
XA343F
A, B, K
HART
C
2108
XA314F
C, D, L
E, F, M
PROFIBUS PA
FOUNDATION Fieldbus
C
2108
XA344F
—
2108
XA233F
4
ATEX II 1/2G EEx d [ia] IIC T6
G
ATEX II 3G EEx nA II T6
A, B, C,
D, K, L
E, F, M
HART,
PROFIBUS PA
FOUNDATION Fieldbus
B
ATEX II 1/2GD EEx ia IIC T6, Alu blind cover
A, B, K
HART
A, B
2108
XA312F
A, B
HART
D
2108
XA312F
C
D
E
42
Housing
ATEX II 1/2G EEx ia IIC T6
ATEX II 1/3D
ATEX II 1/2D, Alu blind cover
ATEX II 1/3D
C, D, L
E, F, M
PROFIBUS PA
FOUNDATION Fieldbus
A, B
2108
XA342F
C, D
E, F
PROFIBUS PA
FOUNDATION Fieldbus
D
2108
XA342F
A, B, K
HART
A, B
2108
XA312F
A, B
HART
D
2108
XA312F
C, D, L
E, F, M
PROFIBUS PA
FOUNDATION Fieldbus
A, B
2108
XA342F
C, D
E, F
PROFIBUS PA
FOUNDATION Fieldbus
D
2108
XA342F
A, B, K
HART
C
2108
XA315F
A, B
HART
A, B, D
2108
XA315F
C, D, L
E, F, M
PROFIBUS PA
FOUNDATION Fieldbus
C
2108
XA345F
C, D
E, F
PROFIBUS PA
FOUNDATION Fieldbus
A, B, D
2108
XA345F
A, B, K
HART
A, D, C
2108
XA315F
A, B
HART
B
2108
XA315F
C, D, L
E, F, M
PROFIBUS PA
FOUNDATION Fieldbus
A, D, C
2108
XA345F
C, D
E, F
PROFIBUS PA
FOUNDATION Fieldbus
B
2108
XA345F
Endress+Hauser
Micropilot M FMR250
Correlation of Control Drawings (ZD) to the instrument:
Instrument
Certificate Explosion
protection
Output
FMR250
S
A, B, K
HART
A, B
ZD168F/00/en
A, B
HART
D
ZD168F/00/en
ZD
PROFIBUS PA
FOUNDATION Fieldbus
A, B
ZD208F/00/en
C, D
E, F
PROFIBUS PA
FOUNDATION Fieldbus
D
ZD208F/00/en
C
ZD169F/00/en
A, B
ZD170F/00/en
FM XP
A, B, K
C, D, L
E, F, M
HART
PROFIBUS PA
FOUNDATION Fieldbus
U
CSA IS
A, B, K
HART
A, B
HART
CSA XP
Housing
C, D, L
E, F, M
T
V
Endress+Hauser
FM IS
Communication
D
ZD170F/00/en
C, D, L
E, F, M
PROFIBUS PA
FOUNDATION Fieldbus
A, B
ZD209F/00/en
C, D
E, F
PROFIBUS PA
FOUNDATION Fieldbus
D
ZD209F/00/en
A, B, K
C, D, L
E, F, M
HART
PROFIBUS PA
FOUNDATION Fieldbus
C
ZD171F/00/en
43
This product may be protected by at least one of the following patents.
Further patents are pending.
•
•
•
•
•
•
•
•
•
•
•
•
•
US 5,387,918 i EP 0 535 196
US 5,689,265 i EP 0 626 063
US 5,659,321
US 5,614,911 i EP 0 670 048
US 5,594,449 i EP 0 676 037
US 6,047,598
US 5,880,698
US 5,926,152
US 5,969,666
US 5,948,979
US 6,054,946
US 6,087,978
US 6,014,100
United States
Canada
Mexico
Endress+Hauser, Inc.
2350 Endress Place
Greenwood, IN 46143
Tel. 317-535-7138
Sales 888-ENDRESS
Service 800-642-8737
fax 317-535-8498
[email protected]
www.us.endress.com
Endress+Hauser Canada
1075 Sutton Drive
Burlington, ON L7L 5Z8
Tel. 905-681-9292
800-668-3199
Fax 905-681-9444
[email protected]
www.ca.endress.com
Endress+Hauser, México, S.A. de C.V.
Fernando Montes de Oca 21 Edificio A Piso 3
Fracc. Industrial San Nicolás
54030. Tlalnepantla de Baz
Estado de México
México
Tel: +52 55 5321 2080
Fax +52 55 5321 2099
[email protected]
www.mx.endress.com
TI390F/24/ae/09.07
© 2007 Endress+Hauser, Inc.