Construction Chemical Anchoring Systems Epoxy and Acrylic Resins Applications A B C E F Construction G D E F G D A Various brackets and supports B D.O.T. dowels, guard rails and “jersey” barriers C Baseplates, safety rails and vibrating equipment Typical Applications D Bolts and special fastening system E Substitute for cast-in-place anchors F Anchor through brick and solid concrete G Can be used for anchoring to hollow brick or block (with perforated screen tubes) Sika® AnchorFix® Cartridge Sika® AnchorFix®-1 Sika® AnchorFix®-1 is a methacrylate 2-part polyester anchoring adhesive, which sets up in just minutes and will cure at temperatures as low as -10ºC (14ºF). Sika® AnchorFix®-2CA Sika® AnchorFix®-2CA an epoxy acrylate exhibits high load capacities, can be dispensed in all types of weather conditions and will cure in colder base material temperatures down to -26 °C. Sika® AnchorFix®-3CA The professional contractor will enjoy the advantages of 100% solids epoxy with superior bond strengths and fast cure times allowing for same day loading of heavy-duty anchors, in concrete, masonry or wood base materials. Sika® AnchorFix®-4CA Excellent long term performance and the same superior bond strengths provided by Sika® AnchorFix®-3CA. Meets the commercial construction industry’s demand for regular set epoxy, with high strength and reliable adhesion to concrete, masonry or wood base materials. Advantages Sika® AnchorFix®-1 Recommended Thickness (min. / max.) Installation Temperature Cure Rate ( ° C ) Installation Shelf-Life Packaging Approvals Features Specifications Sika® AnchorFix®-2CA Sika® AnchorFix®-3CA Sika® AnchorFix®-4CA Acrylate Hybrid Epoxy Acrylate 100% Solid Epoxy 100% Solid Epoxy 1 mm to 3 mm 1 mm to 3 mm 1 mm to 13 mm 1 mm to 13 mm -10 °C to +40 °C -26 °C to +40 °C +5 °C to +40 °C +10 °C to +40 °C -10 24 hrs +5 145 mins +20 50 mins +30 35 mins Overhead Vertical Horizontal -26 -10 +20 +38 +5 +20 +38 +5 +20 +38 36 hrs 6 hrs 35 mins 25 mins 24 hrs 3 hrs 1 hr NR 12 hrs 4 hrs Vertical Horizontal Vertical Horizontal Overhead Vertical Horizontal 12 months 12 months 24 months 24 months 300 mL ctrg 275 mL ctrg 825 mL ctrg None ICC MTQ CFIA Economical Low temperature Very low temperature Fast setting Wet and damp holes Fast setting Wet and damp holes Regular setting Wet and damp holes 2 component / 10:1 ratio 2 component / 10:1 ratio 2 component / 1:1 ratio 2 component / 1:1 ratio 250 mL ctrg 600 mL ctrg 1500 mL ctrg Bulk Pails ICC MTQ NSF CFIA Per NTSB safety recommendations, the use of adhesive anchors are prohibited in sustained overhead load applications 600 mL ctrg Bulk Pails MTQ NSF CFIA Technical Data for Sika® AnchorFix® Tension in 27.5 MPa (4000psi) min. Concrete Load Capacities for Sika® AnchorFix® Adhesives Bit Diameter Construction Anchor Size Thrd Rod mm (in.) Rebar mm (in.) Sika® AnchorFix®-1 Sika® AnchorFix®-2CA Shear (A193B7) Sika® AnchorFix®-3CA & Sika® AnchorFix®-4CA All Sika® AnchorFix® Adhesives Embedment Depth mm (in.) Allowable Load kN (lb) Avg. Ult. Load kN (lb) Allowable Load kN(lb) Avg. Ult. Load kN (lb) Allowable Load kN (lb) Avg. Ult. Load kN (lb) Allowable Load kN (lb) Avg. Ult. Load kN (lb) 10 mm or 10M 11mm (7/16") (3/8" or No. 3) 12mm (1/2") 90mm (3-1/2") 6.1 (1380) 24.6 (5520) 12.3 (2768) 49.3 (11075) 10.5 (2370) 42.2 (9487) 5.0 (1125) 20.0 (4500) 12 mm (1/2" or No. 4) 14mm (9/16") 15mm (5/8") 110mm (4-1/4") 7.8 (1755) 31.2 (7020) 19.0 (4275) 76.1 (17102) 16.7 (3760) 66.9 (15048) 8.9 (2000) 35.6 (8000) 15 mm or 15M (5/8" or No. 5) 20mm (3/4") 20mm (3/4") 125mm (5") 11.0 (2475) 44.0 (9900) 26.6 (5982) 106.4 (23931) 24.1 (5415) 96.4 (21671) 13.9 (3130) 55.7 (12520) 20 mm or 20M (3/4" or No. 6) 22mm (7/8") 22mm (7/8") 170mm (6-3/4") 15.8 (3555) 63.3 (14220) 40.9 (9198) 163.7 (36794) 38.1 (8575) 152.9 (34365) 20.0 (4505) 80.2 (18020) 25mm or 25M 28mm (1-1/8") 28mm (1-1/8") 210mm (8-1/4") (1" or No. 8) 20.1 (4515) 80.3 (18060) 59.3 (13381) 238.1 (53526) 59.6 (13395) 238.3 (53582) 35.6 (8010) 142.5 (32040) NOTES: Allowable load values (safety factor 4:1) are recommended for use in force reaction calculations performed by a qualified design professional. Higher values of safety may be warranted depending upon the actual application and site conditions. Performance values are guidelines for typical, sound base materials. Installation in questionable base material conditions should be tested to determine actual field performance.Shear loads are based upon typical A193B7 steel hardware. Always refer to the latest product technical data available at www.sika.ca for application procedures and handling information. To obtain results not listed in the literature refer to the Sika AnchorFix Design Program available on CD or at www.sika.ca. Per NTSB safety recommendations, the use of adhesive anchors are prohibited in sustained overhead load applications Allowable Anchor Spacing and Edge Distance Reduced Anchor Capacity Distance (Cmin) Full Anchor Capacity Critical Distance (Ccr) Reduction Factor SPACING BETWEEN ANCHORS 24 D 8D 0.9 EDGE DISTANCE: TENSION LOADS 12 D See following chart See following chart SHEAR LOADS – THREADED ROD 12 D 4D 0.21 SHEAR LOADS – SMOOTH DOWELS 12 D 4D 0.21 SHEAR LOADS – REBAR 16 D 4D 0.15 Edge Distance for Tension Values for Anchors in Concrete Stud Size (mm) Minimum Edge Distance (C min) (mm) 10 38 0.7 12 44 0.66 15 44 0.7 20 44 0.7 22 89 0.7 25 102 0.7 32 127 0.7 DISPENSING TOOLS* Sika® AnchorFix®-1 & Sika® AnchorFix®-2CA CARTRIDGE SIZE TOOL TYPE 275 mL (9.3 fl. oz) 300 mL (10.1 fl. oz) Reduction Factor Sika® AnchorFix®-3CA & Sika® AnchorFix®-4CA CARTRIDGE SIZE TOOL TYPE Most standard manual caulking guns (eg : Cox. Ascot dispenser, Chilton dispenser) 825 mL (27.9 fl. oz) 250 ml (8.4 fl. oz) 600 ml (20.2 fl. oz) 1500 mL (50.77 fl. oz) Most competitive manual and pneumatic, dual pistoned dispensing tools (eg: Cox Dual Pneumatic dispenser, 300X. Contact Sika’s Technical Service Department for more information.) Most competitive pneumatic dual pistoned dispensing tools (eg: Cox, PPA. Contact Sika’s Technical Service Department for more information.) * Please refer to the Anchoring Accessories Catalog The information, and in particular, the recommendations relating to the application and end-use of Sika products, are given in good faith based on Sika’s current knowledge and experience of the products when properly stored, handled and applied under normal conditions, within their shelf life. In practice, the differences in materials, substrates and actual site conditions are such that no warranty in respect of merchantability or of fitness for a particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any recommendations, or from any other advice offered. The proprietary rights of third parties must be observed. All orders are accepted subject to our current terms of sale and delivery. Users should always refer to the most recent issue of the Technical Data Sheet for the product concerned, copies of which will be supplied on request or can be accessed in the Internet under www.sika.ca. 1-800-933-SIKA Sika Canada Inc. Ontario Alberta 601 Delmar Avenue Pointe-Claire, QC H9R 4A9 Tel.: (514) 697-2610 Fax: (514) 697-3087 6915 Davand Drive Mississauga, ON L5T 1L5 Tel.: (905) 795-3177 Fax: (905) 795-3192 18131–114th Avenue N.W. www.sika.ca Edmonton, AB T5S 1T8 An ISO 9001:2000 certified company Tel.: (780) 486-6111 Pointe-Claire : ISO 14001:2004 certified EMS Fax: (780) 483-1580
© Copyright 2024