GLITCH360KEY ULTRA INSTALLATION MANUAL v1.5 This Manual will explain you how to install the Glitch360Key Ultra on your xbox 360. For more information about the Reset Glitch Hack check our webpage http://glitch360key.fr Required Tools : - 1x Glitch360Key Ultra ModChip - 1x Glitch360Spi 3.0 rev B (for programming your modchip and using eRGH) - Kynar AWG30, AWG24 and AWG28, Soldering iron 12/15w + soldering tin - Softwares GSU or eRGH & GKU The Glitch360Key Ultra is easy and quick even so please take the time to read the following instructions until the END. Programming the Glitch360Key Ultra Download and install the software GKU. Connect the Glitch360Key Ultra with your Glitch360Spi 3.0 rev B using the FFC Flex cable (see picture below).Then connect the Glitch360Spi 3.0 rev B to your computer using an USB cable (Accept the drivers when prompted) then launch GKU. * How to program your Glitch360Key Ultra depending on your motherboard type: Step 1 : Select your Xbox 360 (FAT or SLIM) Step 2 : Select your Motherboard Step 3 : Select « Glitch360Team » in Chip Manufacturer Step 4 : Choose the timing needed for your motherboard Step 5 : Click on the « FLASH / UPDATE » button * : Dual Nand Feature ON/OFF Your Glitch360Key is now programmed, you can now unplug the flex cable and install it on your Motherboard. Installation details Dual Nand Feature: the command wire of your Dual Nand Modchip should be connected to CMD (ex: wire #11 of the Glitch360Shark). eRGH BenchMark Cloud: Find the best glitch setup for your motherboard! Available from http://cloud.glitch360key.fr, the eRGH BenchMark Cloud allows you to consult the glitch setup (motherboard type, CPU_RST/POST_OUT wire size, switch settings, timing, etc…) shared by other users! This will allow you to find the best glitch settings for your motherboard. You can inspire yourself of the best Benchmark results and use those setting in order to have the best glitch performance for your Xbox 360 INSTALLATION DIAGRAM FOR TRINITY MOTHERBOARD BASIC SWITCH SETUP FOR XBOX 360 TRINITY MOTHERBOARDS SW1 11110010 SW2 00000000 CPU_RST (mm) D 390 AWG30 POST_OUT (mm) C 70 AWG30 Timing Trinity 0 (Default) These setups are basic setups! We advise you to consult the eRGH BenchMark cloud to find the best setup for your motherboard! INSTALLATION DIAGRAM FOR CORONA MOTHERBOARD Note #1: On Corona v3/v4, R2C7 & R2C6 (sometimes also R2C10) must be shorted or replaced with 100 Ohm resistors. Note #2: On Corona v3/v4, the C point is not connected, you must install a POSTFIX Adapter or connect directly under the CPU. CONFIGURATION CONSEILLEE SLIM CORONA SW1 11000010 SW2 00000000 CPU_RST (mm) D 140 AWG28 POST_OUT (mm) C 70 AWG30 Timing Corona 3-2 (Default) These setups are basic setups! We advise you to consult the eRGH BenchMark cloud to find the best setup for your motherboard! INSTALLATION DIAGRAM FOR RGH1.0 FAT MOTHERBOARDS BASIC SWITCH SETUP FOR XBOX 360 RGH1.0 FAT MOTHERBOARDS SW1 10010011 SW2 00000000 CPU_RST (mm) D 200 AWG30 POST_OUT (mm) C 170 AWG30 Timing Depending on version BASIC SWITCH SETUP FOR XBOX 360 RGH1.0 JASPER MOTHERBOARDS SW1 10010111 SW2 00000000 CPU_RST (mm) D 200 AWG30 POST_OUT (mm) C 170 AWG30 Timing Jasper 0 (Default) These setups are basic setups! We advise you to consult the eRGH BenchMark cloud to find the best setup for your motherboard! INSTALLATION DIAGRAM FOR RGH2.0 FAT MOTHERBOARDS BASIC SWITCH SETUP FOR XBOX 360 RGH2.0 FAT MOTHERBOARDS SW1 10011001 SW2 00000000 CPU_RST (mm) D 200 AWG30 POST_OUT (mm) C 170 AWG30 Timing Depending on version FAST COLD BOOT SETUP FOR XBOX 360 RGH2.0 JASPER MOTHERBOARDS SW1 10010001 SW2 00011000 CPU_RST (mm) D 200 AWG30 POST_OUT (mm) C 170 AWG30 Timing Depending on version For Falcon use 1 or B or C timing, for Jasper use B timing, for Zephyr use C or D timing These setups are basic setups! We advise you to consult the eRGH BenchMark cloud to find the best setup for your motherboard! SWITCHS DETAILS SW1 SW2 1. 3,3v Enable/Disable (0 for programming, 1 for glitch) 2. VCCIO 1,8v (SLIM) 3. CPU RST CAP 270pf (Trinity) 4. DISABLE 48Mhz puce (0 = Modchip 48Mhz, 1 = Motherboard) 5. CPU RST 10 Ohm (RGH2) 6. PLL Bypass Cleaner 100nf (Jasper RGH1) 7. CPU RST 8. VCCIO 1,5v (FAT) 1. CPU RST CAP +33pf 2. CPU RST CAP +33pf 3. CPU RST Cleaner 1K Ohm 4. CPU RST Cleaner 3.3K Ohm 5. CPU RST Cleaner 470pf 6. CPU RST Cleaner 680pf 7. PLL Bypass Cleaner 680pf 8. PLL Bypass Cleaner 47nf (zephyr RGH1) Your Glitch360Key Ultra is now correctly programmed and installed  Continue with the eRGH & Glitch360Spi 3.0 rev B Manual v1.4  Continue with the GSU & Glitch360Shark rev B Manual v1.9 Copyrights GlitchTeam 2013 | http://glitch360key.fr/en | http://www.seb117.fr/oshop/ | http://www.flash-miiparis.com V1.5 Glitch360Key Ultra Xbox 360 FAT & Slim Seb117, ZackWarrior, Elyot Made in FRANCE Where to place the Glitch360Key Ultra On FAT Motherboards On CORONA Motherboards On TRINITY Motherboards