AMP-O-LECTRIC Model GII Terminating Machine Fast Facts • Quiet operation • Improved lighting • Toolless changeover of applicators • Precision manual adjust for crimp height • Total and batch counter • Accepts all existing TE applicators, with minor modifications • Reduced maintenance requirements • Split-cycle operation • Standardized 1 5/8 [41.3] stroke • Operates on either 120 or 220 VAC, 50 or 60 Hz The Model “G II” is the latest and most advanced design in the long-standing series of AMP-O-LECTRIC machines for terminating wire using reeled terminals and contacts. It features a reliable and long lasting brush-less motor drive. This unit is designed and built to continue the tradition of “work-horse” terminators from TE. For operator convenience and increased visibility of the work area, we’ve improved access to, and significantly updated lighting in the under cabinet and target area. The Crimp Quality Monitor (CQM II) continues to be located at eye level for bench-top use. The Model “G II” is one of the quietest machines available, plus improved guarding meets applicable European and domestic safety requirements. All Model “G II” versions include precision adjustment for crimp height — an important feature, which, in combination with the optional CQM II, will enable you to maintain the tight tolerances required for today’s demands for higher levels of quality. By simply resetting a dial, an operator can adjust crimp height in 0.013 [.0005”] increments over a 0.457 [.018”] range. Another user-friendly feature is its control system. At the push of a button, you can power the motor on or off, jog forward or reverse, switch to split-cycle operation, turn the work light off or on, power the air feed on or off, or reset the batch counter. And, it’s all reported on an LCD display. The controls will also detect and report errors in the machine, and stop cycling when a bad crimp is detected by the CQM II. The operator must then push the reset button to continue. The Model “G II” will accept all existing TE miniature applicators. AMP-O-LECTRIC Model GII Terminating Machine Specifications and Dimensions Part Number 2217000-1 2217000-2 2217001-1 2217001-2 2217002-1 2217002-2 AMP-O-LECTRIC Model “GII” Machine Versions Description Base unit Base unit, with CQM II Base unit, with stripper module Base unit, with stripper module and CQM II Base unit, Splice machine for end- and side-feed splice applicators Base unit, Splice machine for end- and side-feed splice applicators, with CQM II Specifications Customer Manual - 409-32035 Capacity: 5000 lb [2268 kg] maximum crimp force Air: Pneumatic 80 psi [550 KPa] for models with stripper module. Available as an optional kit for all other models. Electrical: 100/240 VAC, ± 10% AC, 50/60 Hz, Single phase Dimensions (without terminal reel and reel support) Height: 20.5 [520.7mm] Depth: 21.5 [546.1mm] Width: 21.8 [553.7mm] Weight: Approx. 230 lb [104 kg] 807.88 615.78 864.88 558.94 616.44 553.59 591.58 497.66 635.22 535.65 595.80 Optional Stripping Module The combination of the Stripping Module with the AMP-O-LECTRIC Model G Terminator provides an economical and proficient method of stripping wire and crimping terminals on the same machine. Wires are stripped moments before crimping, meaning there is virtually no chance of damaging wire conductors during handling or storage. Once the wire is fed into the start sensor the Stripping Module does the rest, improving placement accuracy. Order Catalog 1309085 for more information. In the interest of continuous improvement, TE reserves the right to modify, discontinue, or replace any products. Catalog 1-1773736-1 / 05-14 / Application Tooling AMP-O-LECTRIC, FASTON, the TE Connectivity (logo) and TE Connectivity are trademarks. www.tooling.te.com TE Connectivity, Harrisburg, PA 17105, Phone: 888-777-5917 or 717-810-2080
© Copyright 2024