Satellite Version Replace your iQ3 Follow these simple steps to swap your current box with your new iQ3. 1 Connect your new iQ3 B 13V/18VDC 350A max Combined Input 1 on’t be a maverick – make sure your TV and existing Foxtel D iQ3 are turned off at the wall. Digital Audio Out Input 2 Remove the cables from your old iQ3, and connect them into the same socket on your new box, one by one. E 12V DC 5A max Optical TV aerial D C Coaxial HDMI USB 5V DC 500mA Ethernet A USB ETHERNET HDMI SPDIF and the double-D symbol are trademarks of Dolby Laboratories. Manufactured under license from Dolby Laboratories. “Dolby” VIDEO Y RF IN LNB-IN1 RF OUT LNB-IN2 Satellite Pb RS-232 Australia Pty Ltd THOMSON Telecom Once you’re connected, turn your TV and iQ3 on and select the HDMI source you’ve connected to. S-VIDEO Terrestrial Pr U.S. patent Nos 4,631,603 ; 4,577, 216 and 4,819,098 licensed for limited pay per view uses only Terrestrial RS-232 RF OUT N10406 RF IN To Foxtel wall plate To TV Y LNB-IN2 LNB-IN2 Satellite RF OUT Y Australia Pty Ltd THOMSON ETHERNETTelecom S-VIDEO DDP060AUS / T500 Terrestrial To internet access point Telecom THOMSON VIDEO Pb SPDIF USB and the double-D symbol are trademarks of Dolby Laboratories. Manufactured under license from Dolby Laboratories. “Dolby” pay per view uses only and 4,819,098 licensed for limited U.S. patent Nos 4,631,603 ; 4,577, 216 (optional) USB Pb VIDEO Australia Pty Ltd LNB-IN1 LNB-IN1 CSO6460V To TV aerial wall plate SPDIF Satellite RF IN N10406 TV Pr S-VIDEO ETHERNETTelecom THOMSON CSO6460V RS-232 TV Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. DDP060AUS / T500 Pr To power point (optional) Terrestrial TV TV Pr 2 Bluetooth pairing your iQ3 remote Bring your remote to the front of the iQ3 until the front of the box lights up. Reset your existing remote by pressing the button located underneath the battery cover. The iQ3 will light up when it connects with your remote. Once the lights on the iQ3 and remote stop flashing, you’re set. Press any button on your remote until the blue light starts to flash. 3 Connecting your iQ3 to the internet To get the most out of your iQ3 features, connect your Ethernet lead from your modem to the back of the iQ3, or connect to WiFi by following these steps: Select Home on your iQ3 remote, then arrow right and select Settings. Select Internet Connection. Select WiFi. Select your network. Enter your WiFi password, select Done and you will be advised once connected. 4 Tune those channels To receive your local free-to-air channels* from your TV aerial, check you’ve connected your iQ3 to your aerial wall plate, then: Select Home, arrow right and select Settings. Select Terrestrial Channels from Settings. Select Full Scan. Select Begin Scan. 5 Activating your iQ3 Nearly done! n the sticker on the outside of your iQ3 O carton, find your box number (the first 16 digits only) and your smartcard number. Then call 1300 732 681 and follow the prompts FOX0020 09/14 SAT/REP You’re now up and running Make sure you return your old iQ3 to us so we can check what went wrong. Just take the enclosed letter, label and your old iQ3 to an Australia Post outlet and we’ll take care of the rest. For troubleshooting or support, go to the Help section in your iQ3 Settings or visit foxtel.com.au/support *Free-to-air channels will vary based on location and not all channels are available in all areas. Once scan is complete select View TV Guide.
© Copyright 2024