http://www.myronanddavis.com Installation Instructions Toyota Highlander NV8THL1 INSTALLATION INSTRUCTIONS AND USE The Myron & Davis In-Dash Navigation System Includes a built in DVD player that should not be viewed by the driver while driving to avoid violation of State and Local Laws. This product should be installed by a professional to ensure proper installation and operation. Myron & Davis is not responsible for any potential accidents, property damage or bodily harm that might result from improper installation or operation. - Read the entire installation instructions prior to performing any work. - Before installation, check to see that all parts are not damaged or defective. 1 - Ensure all appropriate materials are available These are some of the common installation items you will need: - Digital Multi – Meter - Philips screwdriver set -Trim Removing tools - ¼” drive sockets -Torx or Allen-drive wrenches -A functional DVD or CD Myron and Davis Entertainment Systems Multi-Media Navigation System Installation Guide NV8THL1 Rev A Installation Guide 2- Caution -Battery Check the battery to ensure it’s fully charged NOTE: Some new vehicles batteries are not fully charged and may cause improper operation 3 - Warning - Remove the key from the ignition - Disconnect the negative battery terminal - Care must be used working with vehicles with airbags to prevent: - injury - damage to or malfunction of the airbag system - work on malfunctioning systems or components must be performed by certified technicians 4 - Removing the Dash Trim Use caution when removing dash trim components as not to damage or mar the surfaces or damage the fasteners - Inspect all fasteners for damage and replace as necessary. 4 – Removal of the Dash Trim Cont’d. 4 the - Remove AC control StepStep 1. Set foot brake knobs Step 4. Remove driver side trim Step 2. Depress the shift lock. Step 5. Remove Pass. side trim Step 3. Shift into Neutral Step 6. Remove trim from around the radio Step 4 - Remove AC control knobs Step 7. Remove the A/C Controls Step Lift and Step 8.1f.Remove A/Cpush Ventsback A/C vents Step 9. Remove A/C Vents 5 – Remove Factory Radio Remove the OEM Radio and prepare the Myron and Davis Unit for installation by following the steps below. Note: Inspect all fasteners and brackets for damage. Replace as necessary before the installation process is started Step 1. Remove these two upper bolts Step 2. Remove these two lower bolts. Step Step 3.1a. Remove Remove the factory factory radio radio. and disconnect . 1b. Remove the factory Step Step 4. Remove the mounting brackets radio. Step 5. Remove the hazard switch by depressing the clips on the side. Front view of the hazard switch being removed Step 6. Re-attach the mounting brackets to the new radio 6 - GPS Antenna, Optional Satellite Radio, and iPod interface The GPS and Optional Satellite Radio Antenna should be mounted on the exterior of the vehicle and optional iPod interface connector in a user friendly location within the vehicle cabin. Follow the steps below for proper installation. Note: Avoid routing the GPS harness near other power sources to ensure peak operation Step 1. Mount GPS and Satellite radio antenna Step 1a. Connect satellite radio Step 1b. Mount satellite radio and iPod module Step 4 - Position the iPod interface connector conveniently for end user use. Note: The installer is responsible to route the harness not to affect the vehicle safety systems and system installation. Harnesses must be routed away from airbags and other safety systems. 7 - Connect and Install the Myron & Davis unit Follow the steps below to ensure proper installation and connection of the Myron and Davis unit. Note: To ensure that the video cannot be viewed while the vehicle is in motion, connect the (blue/white) Brake Wire to the Emergency Brake Switch (grounded when engaged) Note: Carefully route the wire harnesses so they cannot be damaged during the installation process of the Myron and Davis unit Step 1. Remove transportation screws Step 2. Connect Myron and Davis unit *Note: Be sure to connect the emergency brake for video bypass and the reverse wire if you 8- on Re-install interior trim plan using either the back up sensors and or acomponents back up camera . You will be required to re-install the interior trim components in reverse order of removal after installing the Myron and Davis unit. Please refer to the removal steps in Section 4. Caution: During the installation of the interior trim components, use caution to prevent damage to any of it’s components. Consult the Factory Service Manual for any additional instructions. Caution: After installation of the trim components inspect them to insure they are secure. Final installation view Highlander Built-in navigation antenna interface GPS •ANT Multi-function compound interface Radio antenna Yellow : CDC BATT Red : CDC ACC Black : CDC GROUND Blue : Reverse Blue/White : Foot Brake BRAKE BACK CDC GND CDC BATT CDC ACC • • Connects to •the factory radio harness AV input wire A(optional) • ••• Left channel audio input White Left channel audio input • ••• Right•channel audio input Red Right•channel audio input • ••• 1 out of 3 Video input Yellow Video input TV connecting wire(accessory of TV box) •• •• ••• •• •• Connected to TV box Connected to Factory Aux Input and Steering Wheel Control •Male radar • Camera/radar wire (Accessory of camera/radar) Connected to radar •Female lens • Connected to camer a • ••• Video input Yellow •Optional • Connected to camera iPod adapter (optional) Connected to iPod Multi-function compound interface Multi-function compound interface Connected to tire pressure monitoring module(optional) TPMS•tire pressure monitoring system 5.1-channel audio output wire FL •OUT White FR •OUT Red RL •OUT White RR •OUT Red Front right channel audio output Rear• left channel audio output • Rear• right•channel audio output • C •OUT White Center channel audio output SW •OUT Black Subwoofer audio output SPDIF Yellow Digital audio output External amplifier power control wire AMP •C AV output wire Front left channel audio output L •OUT White Left channel audio output R •OUT Red Right•channel audio output V1 •OUT Yellow Video output port 1 V2 •OUT Yellow Video output port•2 KEY •CON Data control wire http://www.myronanddavis.com 1425 Cooley Court, San Bernardino, CA 92408 Toll Free: 886.335.6789 Fax: 909.799.7300