1. No category

Flush Runway
Centreline Light
Compliances:
LCL
ICAO Annex 14
NATO STANAG 3316
Applications
How to order
These lights are used on runways,
where fittings are required to be
absolutely flush, for runway centreline,
providing a candlepower distribution
substantially conforming to the
photometric performance provided by
the equivalent standard inset lights.
The LCL markers have been
particularly designed for military or
combined civil-military airfields; they
provide a flush surface, eliminate any
arrester hook jump and assure the
correct engagement to the arrester
wire cable.
To the basic part number add the colour for both sides, the electrical system, the
lamp type and the mounting assembly.
If required, any option can be added.
EXAMPLE:
LCL-CC-2P-090-B is a clear-clear flush centreline light with two cable leads with
plug, two 48 W reflectorized lamps, 6.6 A, complete with standard shallow base,
without any lamp by-pass device.
L C L
Features
BASE: made of cast aluminium, with
four holes for fastening the adaptor
ring by means of four screws and two
studs to prevent its rotation due to
aircraft wheel impact/transit. The base
is provided with a bottom hole to allow
the passage of the power supply cable
and for drainage purposes. On
request, special bases can be
supplied.
ADAPTOR RING: made of cast
aluminium, with four through holes to
fix the ring to the base by means of
four screws and two dead holes to
match the base studs. The ring
includes a cylindrical hole for housing
the light unit and two opposite sloping
ramps to allow the beams to merge.
In correspondence of the cylindrical
hole, it is provided with two holes with
threaded inserts, for fastening the light
unit by means of two screws, and
suitable slots to allow the proper
drainage, so no water builds up in
front of the prisms: the light outputs
are not affected under heavy rainfall.
Basic Part
Number:
Colour(Side A)/Colour(Side B):
C = Clear
R = Red
X = Blank
Electrical system:
1P = One Cable Lead
2P = Two Cable Leads
Lamp Type :
045= 1x48W 6.6A Reflectorized
090= 2x48W 6.6A Reflectorized
Mounting Assembly :
B = Standard Shallow Base
O = No Mounting Assembly
Options :
F = Fuse Cutout(s)
E = Electronic Cutout Relay(s)
LIGHT UNIT: consists of a treated
cast aluminium dome and a treated
cast aluminium lower cover, fastened
to the dome by means of three screws
and silicone gasket. The proper
GOLLAND Sp. z o.o.
www.oswietlenielotniskowe.pl
ul. Styczyńskiego 83 41-500 Chorzów
tel. +48 32 349 17 00, +48 32 349 17 01, fax +48 32 349 17 02
e-mail: [email protected]
mounting of the lower cover is
ensured by a pin located in the lower
side of the dome. The dome is
provided with two opposite apertures
for beam outputs. Unidirectional light
units are equipped with an aluminium
screen, mounted in the rear side of a
prism. The lower cover is provided
with one or two glands for cable entry
and with a valve for watertightness
test. Two suitable seats are provided
on the dome to make easy the light
removal.
OPTICAL SYSTEM: consists of two
opposite optical glass prisms, one for
each landing direction; each prism is
mechanically clamped to the light
dome by means of a steel retainer
with silicone gasket. An additional
nylon gasket is placed between each
retainer and prism, to avoid glassmetal direct contact. The prism
replacement is quick and easy and
doesn’t require any sealing.
FILTER: (when required) dichroic
CABLE
red, is mounted in the rear side of a
prism through a suitable stainless
steel support.
LEAD(S):
one or two
according to customer requirement.
Each cable lead consists of two,
single-pole santoprene leads, size 2.5
sq.mm, 0.370 m long, with FAA L -823
plug for very quick coupling with the
relevant receptacle. The leads are
equipped with female faston terminal
and protect by fiberglass silicone
sheath.
LAMP(S):
one for unidirectional
light, two for bidirectional light. The
lamps are 48 W, tungsten-halogen,
6.6 A, 1500 hour rated life, complete
with dichroic reflector and cable leads
with male faston terminal. The lamps
are mounted on a suitable steel plate
through elastic supports for easy and
quick relamping. The lamp plate is
fixed to the lower cover through four
vibration-damping blocks.
LAMP BY-PASS DEVICE(S): on
request, the fitting can be equipped
with two fuse cutouts (option F), each
mounted on a suitable insulated strip
fixed to the lower cover, or with two
electronic cutout relays (option E)
directly fixed to the lower cover.
Unidirectional light mounts one lamp
by-pass device only.
GROUNDING: a suitable screw is
provided on light unit, adaptor ring
and base; a grounding wire with
faston connection is provided between
light unit and adaptor ring and
between the ring and the base .
Outline Drawings
Dimensions in mm
Instruction Manual: UT-MT-191
Light Unit
(2 plugs)
Shipping Weight
3.0 Kg
Shipping Volume
0.007 cu.m
GOLLAND Sp. z o.o.
www.oswietlenielotniskowe.pl
Adaptor Ring
14.0 Kg
0.07 cu.m
Shallow Base
5.5 Kg
0.07 cu.m
Light Unit (2P),
Ring & Shallow Base
21.0 Kg
0.13 cu.m
ul. Styczyńskiego 83 41-500 Chorzów
tel. +48 32 349 17 00, +48 32 349 17 01, fax +48 32 349 17 02
e-mail: [email protected]
Technical Data
Use:
Lamp:
Colour:
GOLLAND Sp. z o.o.
www.oswietlenielotniskowe.pl
Runway centreline
48W 6.6A Reflectorized
Clear
ul. Styczyńskiego 83 41-500 Chorzów
tel. +48 32 349 17 00, +48 32 349 17 01, fax +48 32 349 17 02
e-mail: [email protected]
Accessories
Part Number
Description
011.2050
011.2001
011.2051
011.2008
011.2052
011.2002
011.2559
011.2558
013.1021
712.1012
712.1013
332.3460
738.2001
332.4140
Transformer for series circuits FAA L -831 30/45 W 6.6/6.6 A
Transformer for series circuits FAA L -831 30/45 W 6.6/6.6 A, suitable for secondary grounding
Transformer for series circuits FAA L-831 65 W 6.6/6.6 A
Transformer for series circuits FAA L -831 65 W 6.6/6.6 A, suitable for secondary grounding
Transformer for series circuits FAA L -831 100 W 6.6/6.6 A
Transformer for series circuits FAA L -831 100 W 6.6/6.6 A, suitable for secondary grounding
54-E6-E6 Connector kit L-823, 10-12 AWG (6 sq.mm), 0.42” to 0.585” O.D.
54-E4-E4 Connector kit L-823, 8 AWG (10 sq.mm), 0.42” to 0.585” O.D.
Shallow base, dia. 418 mm, with hardware for adaptor ring fastening.
Setting material for shallow base, 5 lt
Setting material for shallow base, 20 lt
Positioning jig for shallow base installation
Linear level
Lifting tool for light unit removal (two tools need for proper operation)
Renewal Parts
Part Number
Description
153.4000
152.7150
152.7160
152.7031
152.8080
760.2186
152.7190
341.0830
318.1140
325.0310
325.8010
758.2007
752.1001
000.1466
329.3070
202.0010
786.7045
323.2455
325.3474
712.0017
712.0004
752.0003
152.6045
Dome complete with prisms
Lower cover complete with two cable leads with plug
Lower cover complete with one cable lead with plug
Complete lamp supporting plate
Vibration-damping block with hardware
48 W tungsten-halogen lamp, 6.6 A, with dichroic reflector
Dichroic red filter complete with support
Aluminium screen for unidirectional light
Glass prism
Silicone gasket for prism
Nylon gasket for prism
Silicone O-ring for light unit (between dome and lower cover)
Silicone grease for gaskets, 500 gr
Fuse cutout
Insulated strip for fuse cutout
Electronic cutout relay
Valve for watertightness test
L-823 two-pole plug with cable leads, 0.370 m long
Gasket for cable gland
Istantaneous adhesive for cable lead with plug, 20 gr
Anaerobic adhesive, medium type, for screws, 50 cc
Screw paste, 100 gr
Hardware kit for light unit fastening
700.2228 - M10x30 stainless steel HH screw (2 pieces)
706.1106 - Stainless steel elastic washer for M10 screw (2 pieces)
706.5206 - Nylon washer for M10 screw (2 pieces)
We reserve the right to change design or specification data without notice
GOLLAND Sp. z o.o.
www.oswietlenielotniskowe.pl
www.golland.pl
ul. Styczyńskiego 83 41-500 Chorzów
tel. +48 32 349 17 00, +48 32 349 17 01, fax +48 32 349 17 02
e-mail: [email protected]