1. No category

Gear Design Software by Camnetics, Inc.
Yes* additional GearTraxPRO feature only
Add‐on for SolidWorks
Add‐on for AutoDesk Inventor
Add‐on for Solid Edge
User customizable interface
Multiple Components
Multiple Components on a single CAD part
Modifying CAD parts
Internal Spline as a bore on CAD part
Create CAD assemblies
Planetary wizard
High ratio cycloid gear set
On screen animations
Design alerts
3D wireframe
Create XY outputs of involute points (text, Excel, CSV & DXF) Create XYZ outputs of surfaces for spur, bevel and worm gear tooth cuts
Create data sheets:
 Excel
 CVS (Common Separated Values)
 Text
Simple spur gear sizing
Convert GearTrax Legacy files
Single build installs as x32 or x64 depending on operating system
Future enhancements other than bug and CAD release compatibility
Si l
Simple math calculations when entering values
th l l ti
h
t i
l
GearTrax
GearTeq
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Unlimited
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
YYes
Limit 2
Yes*
Yes*
Yes
Yes
Yes*
Yes
Yes*
Yes*
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Y
Yes
Spur and Helical Gears: ANSI‐AGMA 2008‐A88
ANSI‐AGMA 2015‐1‐A01
DIN 867
PGT (1‐4)
British Standards
JIS B 1701
Fellow Stub
Measurements over/under pins
Span measurements (over x number of teeth)
Chordal measurements
Test radius
CAD model suitable for manufacturing
Plastic mold shrinkage
Automatic balance addendum modifications
Racks
Tooth Tip Radius (2016 Release)
Hunting Mesh Information
Hob Protuberance
Face Gears
Parabolic and linear profile modifications
Radial and tapered longitudinal crowned teeth, full and half
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes*
Yes*
Yes*
Yes*
Yes*
Yes*
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Bevel gears, spiral:
Gleason, Spiral and Zerol
Camnetics TruSpiral (accurate involute and true spiral)
Non‐standard
Lead crowning, half and full radial
CAD model suitable for manufacturing
Yes
Yes
Yes
Yes
Yes*
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
GearTrax
GearTeq
Bevel gears, straight:
Gleason
DIN 3971
Non‐standard and Free‐Form
CAD model suitable for manufacturing
Hunting Mesh Information
Lead crowning, half and full radial
Yes
Yes
Yes
Yes
Yes
Yes*
Yes*
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Worm gears:
Models suitable for manufacturing
Worm wheel tooth crowning
Worm measurement over 3 pins
Yes
Yes
Yes*
Yes
Yes
Yes
Yes
Yes
Splines:
ANSI
DIN 5480 and 5482
JIS
CAD models suitable for manufacturing
Deviation chart for DIN and ANSI Module splines
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Chain sprockets:
ANSI
DIN
Special ASA
Sil
Silent Chain ASME_B29_2M_2007
t Ch i ASME B29 2M 2007
Yes
Yes
Yes
Yes
YYes
Yes
Yes
Yes
Yes
YYes
Timing belt pulleys:
MXL, XXL, XL, L, H, XH
HTS 5, 8, 14, 20mm
HTD 3, 5, 8, 14mm
DIN 7721
PowerGrip GT 2, 3, 5, 8, 14
PolyChain GT 8, 14mm
MXL, XXL, XL, L, H, XH models suitable for manufacturing
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Belt pulleys:
A, B, AB, C, D, E
V3, V5, V8
PolyV J, L, M
PolyV H, K
A, B, AB, C, D, E, V3, V5, V8 CAD models suitable for manufacturing
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes* additional GearTraxPRO feature only
ACME Screw and Nut
ACME_Threads_B1_5_1977
Stub_ACME_Threads_B1_5_1977
If you answer yes to any of the following questions then you should consider GearTraxPRO or GearTeq:
Would you consider your company gear professionals?
GearTraxPRO or GearTeq
Will you be doing any profile modification?
GearTraxPRO or GearTeq
Will you be doing any planetary gear sets?
GearTeq
Will you be needing high ration gears sets?
GearTeq
Will you be doing any tooth crowning?
GearTraxPRO or GearTeq
Thoroughly inspect all models before using them for manufacturing.
Last updated: 2015‐05‐05
Camnetics, Inc. www.camnetics.com Voice: 1‐608‐835‐2378
Yes
Yes
Yes