1. technology and computing
2. consumer electronics
3. camera and photo equipment
4. cameras and camcorders
5. cameras

AVWARE AVW517
Features
1
Dimension
2
■ 1/3" SONY SuperHAD CCD Ⅱ (Min. Illumination)
■ Privacy Masking(8 Zone Selectable)
■ Motion Detection(4 Zone Selectable)
■ 3DNR (Digital Noise Reduction) / D - WDR
■ Multi Language (Korean,English,chinese,Japanese)
■ Weather Proof (IP66)
19.5
Specification
10.0<
AVW517
Imaging Sensor
1/3" New SONY Super HAD CCD Ⅱ Dy namic
2:1 Interlace
Scanning System
Scanning Frequency
/ "
S/N Ratio
Horizontal Resolution
Video Output Level
Φ40
28.6
53.5
H:15.734 ㎑ / V:59.94 ㎐
H:15.625 ㎑ / V:50 ㎐
More than 52㏈ (AGC Off)
600 TV-Line (Color)Min / 700 TV-Line (B/W)Min
C
24.8
Item
72.0
1.0 Vp-p (75Ω , Composite)
Lens
3.6㎜ Fixed Lens (92 degree)
Min. Illumination
Unit : mm
3*Φ3.0
Color : 0.03Lux([email protected]) , 0.00019(Sens-up.256x)
Sync System
Internal
O.S.D
Function S/W
Including OSD Control Board
Electronic Shutter Speed
Auto / Flk
(NTSC : 1/60sec ~ 1/100,000sec)
White Balance
(PAL : 1/50sec ~ 1/100,000sec)
UP
AWB / AWC-SET / MANUAL / INDOOR / OUTDOOR/ATW
Backlight Compensation
BLC / HS.BLC / Off
D - WDR
SET
INDOOR / OUTDOOR / Off
Gain Control
Low / Middle / High / Off
Adjust
RIGHT
CONTRAST/SHARPNESS/CB_GAIN/CR_GAIN (Level Adjustable)
Language
Korean / English / Chinese / Japanese (Selectable)
Camera Title
On / Off (Selectable)
Day & Night
Auto / B.W / Color (Selectable) / EXT
Digital Zoom
On / Off(0x ~ 32x)
Motion Detection
On / Off (4 Zone Selectable)
Privacy Masking
On / Off (8 Zone Selectable)
3DNR (Digital Noise Reduction)
after changing a selected item.
On / Off(Selectable limit ~ 256x)
- Up and Down Button : Used to move the cursor up or down in the menu screen to select
Freeze / Mirror / D-Zoom / Gamma / NEG.IMAGE
Supplied Voltage
a desired menu item.
DC12 ±10%
Power Consumption
- Left and Right Button : Used to move the cursor left or right in the menu screen or to
Max. 1.6W[90mA]
Dimension
change the value of the selected item.
19.5(Φ) X 72mm(D)
Weight
DOWN
Funct ion Set Up But t on
- SET Button : Displays the menu on the screen. Press the button to confirm status or
On / Off(Selectable)
Sens - up(Frame Integration)
D - EFFECT
LEFT
Approx.100g
■ Function Menu
3
Function Menu
LENS
■ BRIGHTNESS
■ AGC
■ SENSE-UP
■ BLC/HSBLC
■ D-WDR
■ AWB
■ AWC→SET
■ MANUAL
■ INDOOR
■ OUTDOOR
■ ATW
DAY NIGHT
■ COLOR
■ AUTO
■ EXT
■ B/W
3 DNR
■ ON
■ OFF
■ CAM TITLE
■ D-EFFECT
■ RS485
■ MOTION
■ PRIVACY
■ SYNC
■ LANGUAGE
ADJUST
■ SHARPNESS
■ BLUE
■ RED
RESET
■ FACTORY
SPECIAL
4
▶ SENSE- UP : When it is night of dark, the camera automatically detects the light
■ SHUTTER
WHITE BAL
Manual Lens mode.
▶ A GC : You can adjust it Off, Low, Middle and High level.
The higher the gain level, the brighter the screen but the higher the noise.
■ MANUAL
EXPOSURE
▶ BRI GHT NESS : You can control the brightness by using the Left and Right button in
level and maintains a clear picture.
Notes
This function Deactivates when the AGC "OFF", DAY&NIGHT "OFF"
OFF : Deactivates the Sense-up function.
AUTO : You can adjust brightness by increasing or decreasing the shutter
speed(X2~X256)
* Note that the higher the zoom level, the brighter the screen, but the more likely it
is that an after-image will appear.
* Although Noise, Spots, and Whitish symptoms may occur in SENS-UP operation
when the zoom level is increased, this is normal.
EXIT
▶ BL C : This function allows you to get a clear pictures of objects even the objects in
strong backlight.
• BL C : Enables a user to directly select a desired area from a picture, and to view the
area more clearly
• H S- BL C : If there is a high light installed in a limited environment such as an apartment
parking garage or gas station entrance, removing the hight light makes
it possible to view car license plates efficiently.
How to use the
Notes
⊙ All item with the , you can move to sub menu pressing SET button.
⊙ An item with the - - -, icon is unavailable due to function settings
HS BLC OFF
L ENS
- DA Y
1 . M A NUA L : Only av ailable "M anual" M ode f or f ix ed L ens.
- NI GHT
HS BLC ON
: Even in normal daylight conditions, the HS-BLC is activated.
: If a high light that is larger than certain size is present on the screen
remove the high light to see car license plates clearly.
EXPOSURE
1 . When t he SET UP menu scr een is display ed, select 'EXPOSURE' by using Up and
Dow n but t ons. So t hat t he ar r ow indicat es t he 'EXPOSURE'.
2 . Select a desir ed mode using t he Up and Dow n but t ons.
▶ SHUT T ER : You can select either auto or manual shutter.
- Enable a user to select a mask of high light area
from a picture.
• FL K : Select this mode if flickering occurs on the screen.
Flickering may occures due to imbalance between illumination and frequency.
• A ut o : Select this mode to control the shutter speed automatically.
Shutter speed is automatically controlled depending on the brightness of the screen.
▶ WDR : If there are bright area and dark area on the screen at the same time,
this function makes both areas to be in clear image
- WDR can be selected 3 steps OFF / INDOOR / OUTDOOR
copyright www.avware.de
5
3 Digit al Noise Reduct ion( 3DNR)
● T hi s f unct i on r educes t he back gr ound noi se i n a l ow l umi nance env i r onment
6
1. When t he SET U P menu scr een i s di spl ay ed, sel ect 3DN R by usi ng t he U p and
Dow n but t ons so t hat t he ar r ow i ndi cat es 3DN R.
WDR ON
WHI T E BA L A NCE ( Whit e Bal.)
2. Sel ect a desi r ed mode usi ng t he L ef t and Ri ght but t ons.
▶ OFF : Deactivates 3DNR. Noise is not reduced.
WDR OFF
▶ ON : Activates 3DN so that noise is reduced.
1. When SET U P menu scr een i s di spl ay ed, sel ect 'Whi t e Bal .' by usi ng U p and
3. Set t he 3DN R mode t o 'ON ' andpr ess t he SET but t on. T hen y ou can adj ust t he
Dow n but t ons so t hat t he ar r ow i ndi cat es Whi t e Bal .
N oi se r educt i on l ev el .
※ Sel ect one of t he f ol l ow i ng 6 modes, as appr opr i at e f or y our pur pose
▶ A WB : Select this when the color temperature is between 2,000ºK and 18,000ºK.
Notes
⊙ You cannot set the 3DNR to 'ON' or 'OFF' when the AGC mode of the EXPOSURE menu is
'OFF'.
⊙ When adjusting the noise reduction level of the 3DNR mdoe, the higher the level set ,
the more the noise level will be reduced but that after image may also occur.
▶ A WC- > SET : To find the optimal setting for the current luminance environment in this
mode, set the point the camera towards a sheet of white paper and press
the SET button. If the environment changes, readjust it.
▶ M A N U A L : Select this to fine-tune White Balance manually. Set White Balance first by using
the ATW or AWC mode. After that switch to MANUAL mode.
SPECI A L
Adjust the [BLUE] and [RED], according to the changing of color on the screen
1. When t he SET U P menu scr een i s di spl ay ed, sel ect 'SPECI A L ' by usi ng U p and
▶ I N DOOR : Select this when the color temperature is around 3,100ºK.
Dow n but t ons so t hat t he ar r ow i ndi cat es 'SPECI A L '
▶ OU T DOOR : Select this when the color temperature is around 5,100ºK.
2. Sel ect a desi r ed mode usi ng t he U p and Dow n but t ons
▶ A T W : Select this when the color temperature is between 2,500ºK and 9,800ºK.
▶ CA M T I T L E : If you enter a title, the title will be appear on the monitor.
① If the SPECIAL menu screen is displayed, use the Up and Down buttons so that the arrow
Notes
indicates 'CAM TITLE'
⊙ White balance may not work properly under the following conditions.
In this case, select the AWC mode.
① When color temperature of environment surrounding the subject is out of the control range
② If the camera towards a fluorescent, the White Balance operation may become unstable
② Set it to 'On' by using Left and Right buttons.
Notes
⊙ When the CAM TITLE menu is 'OFF', no title will be displayed on the monitor screen even if
you
DA Y/ NI GHT
● You can di spl ay pi ct ur es i n Col or or Bl ack and Whi t e.
③ Press the SET button.
1. When t he SET U P menu scr een i s di spl ay ed, sel ect 'DA Y/ N I GH T ' by usi ng t he U p
④ Use the 4 direction buttons to move to a desired letter and select the letter by pressing the
SET button. Repeat this to enter multiple letters. You can enter up 15 letters.
and Dow n but t ons so t hat t he ar r ow i ndi cat es 'DA Y/ N I GH T '
▶ COL OR : The picture is always displayed in color.
Notes
⊙ If you entered wrong letter……
If you move the cursor to CLR and press the SET button, all the letters are deleted. To edit a
leeter,
change the cursor to the bottom left arrow and press the SET button. Move the curson over the
▶ A U T O : The mode is switched to color in a normal environment, but switches to B/W mode
when ambient illumination is low. To set up the switching time or speed
for auto mode, press the SET button
- Delay : You can select the duration time about changing the day/night mode.
⑤ Enter a title, move the cursor to 'POS' and press the SET button. The entered title appears
- S / E - Level : You can select brightness of illumination about changing the day/night mode.
on the screen. Select the position to display the title on the screen by using the 4 directoin
-> The brightness of illumination is changeable by installed environment.
buttons and press the SET button. When the position is determined, select 'END' and press
▶ EXT : Deactivates the EXT function.
the SET button to return to the SPECIAL menu.
▶ BW : The picture is always displayed in B/W.
▶ D- EFFECT
① When the SPECIAL menu screen is displayed, press the Up and down buttons so that the
Notes
arrow indicates "D-EFFECT".
⊙ You cannot control the DAY/NIGHT menu when AGC in the EXPOSURE menu is 'OFF'
At this time, the exchange between DAY mode and NIGHT mode operates as COLOR mode
* Mirror
- Mirror : you can flip the image vertically on the screen.
- Rotate : you can flip the imate horizontally on the screen.
- V-Flip : you can flip the image vertically and horizontally both.
* Digital Zoom : You can use a digital zoom of x1.0 ~ X32
② Press the SET button for Sub menu.
* Freeze : You can stop the image or reactivate it.
7
▶ PRI V A CY : Hide an area you want to hide on the screen.
① When the SPECIAL menu screen is displayed, press the Up and Down buttons so that the
arrow indecates 'PRIVACY'.
② Press SET button for Sub Menu.
③ Set up the mode by using 4 direction buttons.
* Gamma : Standard value is 0.45. You can adjust the value between 0.05 ~ 1.00
* AREA SELECT : You can select up to 8 privacy areas.
* NEG IMAGE : you can flip the color on screen.
* AREA DISPLAY : Determines whether to use the area selected in the AREA SELECT.
▶ RS 485 : Deactivates the RS485 function.
* LEFT / RIGHT : Determines the coordinate of the vertical axis for Area.
▶ M OT I ON : If you connect an alarm device to this camera, you can monitor activity
* WIDTH : adjust the selected vertical area.
because a signal is generated by the camera whenever motion is detected. The
* TOP / BOTTOM : Determines the coordinate of the horizontal axis for area.
motion detection signal is output through the MD OUT port.
* HEIGHT : adjust the selected horizontal area.
① When the SPECIAL menu is displayed, press the
* COLOR : Determine area color. You can select 0 ~ 15.
Up and Down buttons so that arrow indicates
▶ L anguage : You can select the menu language according to your requirement.
MOTION.
② Press SET button for sub menu.
- It can be changes 5sec. later.
③ Set up the mode using 4 direction buttons.
- Supplied Language : English, Chinese, Japanese
* AREA SELECT : Determines which 4 vertices of
each MD area is to be used
* AREA DIPLAY : Determines whetehr to use the MD area selected in Sensitivity.
* LEFT / RIGHT : Determines the coordinate of the vertical axis for Area.
* WIDTH : Adjust the selected vertical area.
A DJUST
1. When t he SET U P menu scr een i s di spl ay ed, sel ect A DJU ST by usi ng U p and
Dow n but t ons so t hat ar r ow i ndi cat es A DJU ST .
▶ Shar pness : As you increase this value, the picture outline becomes stronger and clearer
* TOP / BOTTOM : Determines the coordinate of the horizontal axis for area.
* HEIGHT : Adjust the selected horizontal area.
Adjust this value appropriately depending on the sharpness of the picture.
▶ BL U E : You can adjust the color on the monitor in BLUE mode by controlling between
* Sensitivity : You can select up to 4 areas. When sensitivity number is high,
motion detection sensitivity is increased to recognize even small movement
0 and 100
▶ RED : You can adjust the color on the monitor in RED mode by controlling between
* Motion View : If you make it ON by using LEFT and RIGHT buttons, selected
0 and 100
value of color is filled on the screen
RESET
Notes
⊙ MD areas show only MOTION menu. Therefore, MD areas don't display on the monitor screen.
⊙ BUT if you select the motion view function ON, MD areas are displayed on the monitor
1. When t he SET U P menu scr een i s di spl ay ed, sel ect RESET by usi ng U p and
Dow n but t ons so t hat ar r ow i ndi cat es RESET .
2. Sel ect a mode by usi ng U p and Dow n but t ons.
▶ FA CT ORY : Resets the camera settings to the factory defaults.
Language and Communication status is not initialized
EXI T
Press the SET button in the Exit menu to save the current settings and exit the Main SETUP
menu.
copyright www.avware.de
8